2,482 research outputs found

    The effects of high power diode laser radiation on the wettability, adhesion and bonding characteristics of an alumina/silica-based oxide and vitreous enamel

    Get PDF
    An amalgamated alumina/silica-based oxide compound (AOC) was surface treated using a 60 W high power diode laser (HPDL). The effects of HPDL radiation on the wettability and adhesion characteristics of the AOC and a vitreous enamel have been determined. The basic process phenomena are investigated and the effects of laser irradiation in terms of composition and microstructure are presented. Without laser treatment of the AOC surface it was not possible to fire the enamel onto the AOC. However, wetting experiments using a number of control liquids, by the sessile drop technique, revealed that laser treatment of the AOC surface resulted in the polar component of the surface energy increasing after laser treatment from 2.00 mJm-2 to 16.15 mJm-2. Additionally, surface roughness measurements revealed that after laser treatment, the surface roughness had decreased from an Ra value of 25.85Îźm to 6.27Îźm, whilst an energy disperse X-ray analysis (EDX) revealed that the relative surface oxygen content of the AOC had increased by 36.29% after laser treatment. Thus, laser treatment was identified as effecting a decrease in the enamel contact angle from 1180 to 330; consequently allowing the vitreous enamel to wet the surface. The bonding mechanisms were identified as being principally due to van der Waals forces, however, some evidence of chemical bonding was observed. The work has shown clearly that laser radiation can be used to alter the wetting characteristics of the AOC

    High power diode laser marking and engraving of building materials

    Get PDF
    A Diomed 60W-cw high power diode laser (HPDL) has been used for the marking and engraving of various building materials, including; marble, granite, clay tiles, ceramic tiles, roof tiles, ordinary Portland cement (OPC) and clay bricks. Morphological and microstructural characteristics are presented. The basic mechanisms of marking/engraving and characteristics of the beam absorption are described. The effects of material texture, colour and laser processing parameters are reported. The work shows that engraving depths of over 2mm (0.75mm for a single pass) can be achieved on marble substrates by thermal disintegration of CaCO3 into loose CaO powder and CO2 gas. Uniform amorphous glazed lines (1-3mm line width) of a colour different from the untreated materials can be generated on clay tiles, ceramic tiles, roof tiles, clay bricks and OPC by solidification phase formation after laser melting of these materials. Effects of atmospheric conditions, for instance using O2 and Ar gas shrouds, have been examined, with different coloured marks being observed when different shroud gases are used. To demonstrate the practical worth of the process a UMIST crest has been marked on a ceramic tile using the system. Laser beam reflectivity is found to depend not only on material composition but also its colour. Reflectivity has been found to range between 12% to 18% for the various construction materials used in the experiment, except for marble (grey) which showed over 27% reflectivity. Since the HPDL is a portable device, in-field application of these processing techniques can be realised, which would be either impossible or difficult when using other types of lasers

    Grout or mortar removal by lasers

    Get PDF
    The method comprises the steps of directing the beam of a portable laser device (40) onto grout (14) at a power level to cause removal of the grout; causing mutual relative movement between said laser beam and said grout; and, providing removal means (30, 32) for debris resulting from said grout removal. The laser beam (16) is transmitted to the grout (14) via optical fibre. The laser is selected from the group comprising: Nd-YAG laser; semi-conductor laser; and, diode pumped fibre laser, and may also include a low-power visible aiming laser. An area of grout being treated is surrounded by an enclosure (22) to prevent escape of laser light. The enclosure is transparent to optical light and opaque to laser light of the wavelength, e.g. 0.4 to 10.6 $g(m)m, in use. The laser beam spot (18) size being commensurate with the grout width. Debris removal means, possibly assisted with a gas jet (42), comprises suction removal (44) at a position adjacent the grout laser treatment area. The method may include the step of applying additional water to the grout

    Surface modification of an Al2O3/SiO2 based ceramic treated with CO2, Nd:YAG, excimer and high power diode lasers for altered wettability characteristics

    Get PDF
    Interaction of CO2, Nd:YAG, excimer and high power diode laser (HPDL) radiation with the surface of an Al2O3/SiO2 based ceramic was found to affect significant changes in the wettability characteristics of the material. It was observed that interaction with CO2, Nd:YAG and HPDL radiation reduced the enamel contact angle from 1180 to 310, 340 and 330 respectively. In contrast, interaction with excimer laser radiation resulted an increase in the contact angle to 1210. Such changes were identified as being due to: (i) the melting and partial vitrification of the Al2O3/SiO2 based ceramic surface as a result of interaction with CO2, Nd:YAG HPDL radiation. (ii) the surface roughness of the Al2O3/SiO2 based ceramic increasing after interaction with excimer laser radiation. (iii) the relative surface oxygen content of the Al2O3/SiO2 based ceramic increasing after interaction with CO2, Nd:YAG and HPDL radiation. The work has shown that the wettability characteristics of the Al2O3/SiO2 based ceramic could be controlled and/or modified with laser surface treatment. Moreover, it was found that changes in the wettability characteristics of the Al2O3/SiO2 based ceramic are related to the effects of laser wavelength, that is whether the wavelength of the laser radiation has the propensity to cause surface melting

    Laser materials processing with diode lasers

    Get PDF
    Laser materials processing is currently dominated by CO2, Nd-YAG and Excimer lasers. Continuous advances in semiconductor laser technology over the last decade have increased the average power output of the devices annualy by two fold, resulting in the commercial availability of the diode lasers today with delivery output powers in excess of 60W in CW mode and 5kW in qasi-CW mode. The advantages of compactness, high reliability, high efficiency and potential low cost, due to the mass production capability of the diode laser, will inextricably shape its future in the field of materials processing. This papers reports on work exploring the feasibility of a range of materials processing applications using a Diomed 60W diode laser, transmitted through a 600m diameter optical fibre and coupled to a 3 axis CNC workstation. The applications studied include; marking and engraving natural stones (marble and granite), marking ceramic tiles, glazing and sealing tile grouts, marking and cutting glass, marking wood, welding metal wire and transformation hardening of tool steels. The study shows that even at the present limited power level of diode laser, many materials processing applications can be accomplished with satisfactory results. Through the study an initial understanding of interaction of diode laser beam with various materials has been gained. Also, within the paper basic beam characteristics, the state of the art of high power diode laser technology and current materials processing applications are also reviewed

    Ceramic tile grout removal & sealing using high power lasers

    Get PDF
    Work has been conducted using a Nd:YAG laser, a CO2 laser and a high power diode laser (HPDL) in order to determine the feasibility of removing contaminated tile grout from the void between adjoining vitrified ceramic tiles, and to seal the void permanently with a material having an impermeable surface glaze. Reported on in the paper are; the basic process phenomena, the process effectiveness, suitable vitrifiable material development, a heat affect study and a morphological and compositional analysis

    Achieving landscape-scale deer management for biodiversity conservation: The need to consider sources and sinks

    Get PDF
    Hyper-herbivory following predator removal is a global issue. Across North America and Europe, increasing deer numbers are affecting biodiversity and human epidemiology, but effectiveness of deer management in heterogeneous landscapes remains poorly understood. In forest habitats in Europe, deer numbers are rarely assessed and management is mainly based on impacts. Even where managed areas achieve stable or improving impact levels, the extent to which they act as sinks or persist as sources exporting deer to the wider landscape remains unknown. We present a framework to quantify effectiveness of deer management at the landscape scale. Applied across 234 km2 of Eastern England, we assessed management of invasive Reeve’s muntjac (Muntiacus reevesi) and native roe (Capreolus capreolus), measuring deer density (using thermal imaging distance transects 780 km/year), fertility, neonatal survival, and culling to quantify source-sink dynamics over 2008–2010. Despite management that removed 23–40% of the annual population, 1,287 (95% CI: 289–2,680) muntjac and 585 (454–1,533) roe deer dispersed annually into the wider landscape, consistent with their ongoing range expansion. For roe deer, culled individuals comprised fewer young deer than predicted by a Leslie matrix model assuming a closed population, consistent with agedependent emigration. In this landscape, for roe and muntjac, an annual cull of at least 60% and 53%, respectively, is required to offset annual production. Failure to quantify deer numbers and productivity has allowed high density populations to persist as regional sources contributing to range expansion, despite deliberative management programs, and without recognition by managers who considered numbers and impacts to be stable. Reversing an unfavorable condition of woodland biodiversity requires appropriate culls across large contiguous areas, supported by knowledge of deer numbers and fertility

    A method of improving wettability and enamelling

    Get PDF
    There is described a method of enamelling a substrate, the method including the steps of: treating a thin surface layer of said substrate with a laser beam so as to promote a change in the surface energy thereof; allowing the surface to cool; and, applying enamel thereto to wet and coat said substrate
    • …
    corecore