137,950 research outputs found
The modeling of distributed RC networks
Modeling of general three terminal distributed RC network
“Home Again”: The Contrasting Experiences of Richard D. Dunphy and Lewis A. Horton
Union veterans returning home from the war in 1865 faced a myriad of experiences and reacted to the return to civilian life in a variety of ways. Richard D. Dunphy and Lewis A. Horton, both double-arm amputee veterans of the Navy, ably demonstrate the differences in experience and reaction to the war and life afterwards. [excerpt
Inflation with in Jordan frame
We consider an action that is non-minimally coupled to a massive
scalar field. The model closely resembles scalar-tensor theory and by conformal
transformation can be transformed to Einstein frame. To avoid the ambiguity of
the frame dependence, we obtain an exact analytical solution in Jordan frame
and show that the model leads to a period of accelerated expansion with an
exit. Further, we compute the scalar and tensor power spectrum for the model
and compare them with observations.Comment: 10 pages, 3 figure
Exact inflationary solutions in exponential gravity
We consider a modified gravity model of the form , where the strong gravity corrections are taken to all orders and is a
self-interacting massless scalar field. We show that the conformal
transformation of this model to Einstein frame leads to non-canonical kinetic
term and negates the advantage of the Einstein frame. We obtain exact solutions
for the background in the Jordan frame without performing conformal
transformations and show that the model leads to inflation with exit. We obtain
scalar and tensor power-spectrum in Jordan frame and show that the model leads
to red-tilt. We discuss the implications of the same in the light of
cosmological observations.Comment: 17 pages, 4 figures, 2 table
Formation of nanocrystals based on decomposition in the amorphous Zr41.2Ti13.8Cu12.5Ni10Be22.5 alloy
Primary crystallization and decomposition in the bulk amorphous alloy Ar41.2Ti13.8Cu12.5Ni10Be22.5 have been studied by small angle neutron scattering (SANS), transmission electron microscopy (TEM), and differential scanning calorimetry (DSC). SANS data of samples annealed isothermally at 623 K exhibit an interference peak centered at q=0.46 nm(^-1) after an incubation time of about 100 min. TEM and DSC investigations confirm that the respective periodic variation in the scattering length density is due to the formation of nanocrystals embedded in the amorphous matrix. These observations suggest that during the incubation time a chemical decomposition process occurs and the related periodic composition fluctuations give rise to the observed periodic arrangement of the nanocrystals
Helical channel design and technology for cooling of muon beams
Novel magnetic helical channel designs for capture and cooling of bright muon
beams are being developed using numerical simulations based on new inventions
such as helical solenoid (HS) magnets and hydrogen-pressurized RF (HPRF)
cavities. We are close to the factor of a million six-dimensional phase space
(6D) reduction needed for muon colliders. Recent experimental and simulation
results are presented.Comment: 6 pp. 14th Advanced Accelerator Concepts Workshop 13-19 Jun 2010:
Annapolis, Marylan
Investigation of fiber bridging in double cantilever beam specimens
The possibility to eliminate fiber bridging or at least to reduce it, and to evaluate an alternative approach for determination of in situ mode 7 fracture toughness values of composite matrix materials were investigated. Double cantilever beam (DCB) specimens were made using unidirectional lay-ups of T6C/Hx205 composite material in which the delaminating halves were placed at angles of 0, 1.5, and 3 degrees to each other. The small angles between the delaminating plies were used to avoid fiber nesting without significantly affecting mode I teflon insert. The DCB specimens were fabricated and it was found that: (1) the extent which fiber bridging and interlaminar toughness increase with crack length can be reduced by slight cross ply at the delamination plane to reduce fiber nesting; (2) some fiber bridging may occur even in the absence of fiber nesting; (3) the first values of toughness measured ahead of the thin teflon insert are very close to the toughness of the matrix material with no fiber bridging; (4) thin adhesive bondline of matrix material appears to give toughness values equal to the interlaminar toughness of the composite matrix without fiber bridging
Influence of the resin on interlaminar mixed-mode fracture
Both literature review data and new data on toughness behavior of seven matrix and adhesive systems in four types of tests were studied in order to assess the influence of the resin on interlaminar fracture. Mixed mode (i.e., various combinations of opening mode 1, G sub 1, and shearing mode 2; G sub 2) fracture toughness data showed that the mixed mode relationship for failure appears to be linear in terms of G sub 1 and G sub 2. The study further indicates that fracture of brittle resins is controlled by the G sub 1 component, and that fracture of many tough resins is controlled by total strain-energy release rate, G sub T. Regarding the relation of polymer structure and the mixed mode fracture: high mode 1 toughness requires resin dilatation; dilatation is low in unmodified epoxies at room temperature/dry conditions; dilatation is higher in plasticized epoxies, heated epoxies, and in modified epoxies; modification improves mode 2 toughness only slightly compared with mode 1 improvements. Analytical aspects of the cracked lap shear test specimen were explored
- …