t-c gamma and t-cg in warped extra dimensions

In this work, we calculate the top quark rare decays t-cgamma and t-cg in the framework where the standard model is embedded in a warped extra dimension with the custodial symmetry SU(3)c*SU(2)L*SU(2)R*U(1)x*PLR. Adopting reasonable assumptions on the parameter space,we numerically find the branching ratios of t-cgamma exceeding 10^-6 and that of t-cg exceeding 10^-5 respectively, which can be detected in near future.Comment: arXiv admin note: text overlap with arXiv:0903.2415 by other author

Superconducting proximity effect to the block antiferromagnetism in Ky_{y}Fe2−x_{2-x}Se2_{2}

Recent discovery of superconducting (SC) ternary iron selenides has block antiferromagentic (AFM) long range order. Many experiments show possible mesoscopic phase separation of the superconductivity and antiferromagnetism, while the neutron experiment reveals a sizable suppression of magnetic moment due to the superconductivity indicating a possible phase coexistence. Here we propose that the observed suppression of the magnetic moment may be explained due to the proximity effect within a phase separation scenario. We use a two-orbital model to study the proximity effect on a layer of block AFM state induced by neighboring SC layers via an interlayer tunneling mechanism. We argue that the proximity effect in ternary Fe-selenides should be large because of the large interlayer coupling and weak electron correlation. The result of our mean field theory is compared with the neutron experiments semi-quantitatively. The suppression of the magnetic moment due to the SC proximity effect is found to be more pronounced in the d-wave superconductivity and may be enhanced by the frustrated structure of the block AFM state.Comment: 6 pages, 6 figure

A high performance surface acoustic wave visible light sensor using novel materials: Bi2S3 nanobelts

Low dimensional Bi2S3 materials are excellent for use in photodetectors with excellent stability and fast response time. In this work, we developed a visible light sensor with good performance based on surface acoustic wave (SAW) devices using Bi2S3 nanobelts as the sensing materials. The SAW delay-line sensor was fabricated on ST-cut quartz with a designed wavelength of 15.8 microns using conventional photolithography techniques. The measured center frequency was 200.02 MHz. The Bi2S3 nanobelts prepared by a facile hydrothermal process were deposited onto SAW sensors by spin-coating. Under irradiation of 625 nm visible light with a power intensity of 170 μW cm−2, the sensor showed a fast and large response with a frequency upshift of 7 kHz within 1 s. The upshift of the frequency of the SAW device is mainly attributed to the mass loading effect caused by the desorption of oxygen from the Bi2S3 nanobelts under visible light radiation

Edge states in self-complementary checkerboard photonic crystals: Zak phase, surface impedance and experimental verification

Edge states of photonic crystals have attracted much attention for the potential applications such as high transmission waveguide bends, spin dependent splitters and one-way photonic circuits. Here, we theoretically discuss and experimentally observe the deterministic edge states in checkerboard photonic crystals. Due to the self-complementarity of checkerboard photonic crystals, a common band gap is structurally protected between two photonic crystals with different unit cells. Deterministic edge states are found inside the common band gap by exploiting the Zak phase analysis and surface impedance calculation. These edge states are also confirmed by a microwave experiment.Comment: 13 pages, 4 figure

A high performance surface acoustic wave visible light sensor using novel materials: Bi2S3 nanobelts

Low dimensional Bi2S3 materials are excellent for use in photodetectors with excellent stability and fast response time. In this work, we developed a visible light sensor with good performance based on surface acoustic wave (SAW) devices using Bi2S3 nanobelts as the sensing materials. The SAW delay-line sensor was fabricated on ST-cut quartz with a designed wavelength of 15.8 microns using conventional photolithography techniques. The measured center frequency was 200.02 MHz. The Bi2S3 nanobelts prepared by a facile hydrothermal process were deposited onto SAW sensors by spin-coating. Under irradiation of 625 nm visible light with a power intensity of 170 μW cm−2, the sensor showed a fast and large response with a frequency upshift of 7 kHz within 1 s. The upshift of the frequency of the SAW device is mainly attributed to the mass loading effect caused by the desorption of oxygen from the Bi2S3 nanobelts under visible light radiation