48 research outputs found
Probing Mechanical Properties of Water-Crude Oil Interfaces and Colloidal Interactions of Petroleum Emulsions using Atomic Force Microscopy
Atomic force microscopy (AFM) is frequently used to elucidate complex interactions in emulsion systems. However, comparing results obtained with âmodelâ planar surfaces to curved emulsion interfaces often proves unreliable, because droplet curvature can affect adsorption and arrangement of surface-active species, while droplet deformation affects the net interaction force. In the current study, AFM was used to study the interactions between a colloidal probe and water droplet. Force magnitude and water droplet deformation were measured in toluene solutions of asphaltene or bitumen at different concentrations and varying droplet aging time. Interfacial stiffening and an increase in particleâdroplet adhesion force were observed upon droplet aging in bitumen solution. As reported in our previous study (Kuznicki, N. P., Harbottle, D., Masliyah, J., and Xu, Z.Dynamic Interactions between a Silica Sphere and Deformable Interfaces in Organic Solvents Studied by Atomic Force Microscopy. Langmuir 2016, 32 (38), 9797â9806), a viscoelasticity parameter should be included in the high-force StokesâReynoldsâYoungâLaplace (SRYL) equations to account for the interfacial stiffening and non-Laplacian response of the water droplet at longer aging times. However, following the addition of a biodegradable demulsifier, ethyl cellulose (EC), an immediate reduction in both the particleâdroplet adhesion force and the rigidity of the water droplet occurred. Following EC addition, the interface reverted back to a Laplacian response and droplet deformation was once again accurately predicted by the classical SRYL model. These changes in both droplet deformation and particleâdroplet adhesion, tracked by AFM, imply a rapid asphaltene/bitumen film displacement by EC molecules. The colloidal probe technique provides a convenient way to quantify forces at deformable oil/water interfaces and characterize the in situ effectiveness of competing surface-active species
Role of Caustic Addition in Bitumen-Clay Interactions
Coating of bitumen by clays, known as slime coating, is detrimental to bitumen recovery from oil sands using the warm slurry extn. process. Sodium hydroxide (caustic) is added to the extn. process to balance many competing processing challenges, which include undesirable slime coating. The current research aims at understanding the role of caustic addn. in controlling interactions of bitumen with various types of model clays. The interaction potential was studied by quartz crystal microbalance with dissipation monitoring (QCM-D). After confirming the slime coating potential of montmorillonite clays on bitumen in the presence of calcium ions, the interaction of kaolinite and illite with bitumen was studied. To represent more closely the industrial applications, tailings water from bitumen extn. tests at different caustic dosage was used. At caustic dosage up to 0.5 wt % oil sands ore, a negligible coating of kaolinite on the bitumen was detd. However, at a lower level of caustic addn., illite was shown to attach to the bitumen, with the interaction potential decreasing with increasing caustic dosage. Increasing concn. of humic acids as a result of increasing caustic dosage was identified to limit the interaction potential of illite with bitumen. This fundamental study clearly shows that the crit. role of caustics in modulating interactions of clays with bitumen depends upon the type of clays. Thus, clay type was identified as a key operational variable
Understanding mechanisms of asphaltene adsorption from organic solvent on mica
The adsorption process of asphaltene onto molecularly smooth mica surfaces from toluene solutions of various concentrations (0.01-1 wt %) was studied using a surface forces apparatus (SFA). Adsorption of asphaltenes onto mica was found to be highly dependent on adsorption time and asphaltene concentration of the solution. The adsorption of asphaltenes led to an attractive bridging force between the mica surfaces in asphaltene solution. The adsorption process was identified as being controlled by the diffusion of asphaltenes from the bulk solution to the mica surface with a diffusion coefficient on the order of 10-10 m2/s at room temperature, depending on the asphaltene bulk concentration. This diffusion coefficient corresponds to a hydrodynamic molecular radius of approximately 0.5 nm, indicating that asphaltene diffuses to mica surfaces as individual molecules at very low concentration (e.g., 0.01 wt %). Atomic force microscopy images of the adsorbed asphaltenes on mica support the results of the SFA force measurements. The results from the SFA force measurements provide valuable insights into the molecular interactions (e.g., steric repulsion and bridging attraction as a function of distance) of asphaltenes in organic media and hence their roles in crude oil and bitumen production
Demulsification mechanism of asphaltene-stabilized water-in-oil emulsions by a polymeric ethylene oxide-propylene oxide demulsifier
The demulsification mechanism of asphaltene-stabilized water-in-toluene emulsions by an ethylene-oxide-propylene oxide (EO-PO) based polymeric demulsifier was studied. Demulsification efficiency was determined by bottle tests and correlated to the physicochemical properties of asphaltene interfacial films after demulsifier addition. From bottle tests and droplet coalescence experiments, the demulsifier showed an optimal performance at 2.3 ppm (mass basis) in toluene. At high concentrations, the demulsification performance deteriorated due to the intrinsic stabilizing capacity of the demulsifier, which was attributed to steric repulsion between water droplets. Addition of demulsifier was shown to soften the asphaltene film (i.e., reduce the viscoelastic moduli of asphaltene films) under both shear and compressional interfacial deformations. Study of the macrostructures and the chemical composition of asphaltene film at the toluene-water interface after demulsifier addition demonstrated gradual penetration of the demulsifier into the asphaltene film. Demulsifier penetration in the asphaltene film changed the asphaltene interfacial mobility and morphology, as probed with Brewster angle and atomic force microscopy