70,182 research outputs found
Equations of motion in the linear approximation
Gauge invariant theory of motion of singularities in linear approximatio
High-temperature constitutive modeling
Thermomechanical service conditions for high-temperature levels, thermal transients, and mechanical loads severe enough to cause measurable inelastic deformation are studied. Structural analysis in support of the design of high-temperature components depends strongly on accurate mathematical representations of the nonlinear, hereditary, inelastic behavior of structural alloys at high temperature, particularly in the relatively small strain range. Progress is discussed in the following areas: multiaxial experimentation to provide a basis for high-temperature multiaxial constitutive relationships; nonisothermal testing and theoretical development toward a complete thermomechanically path dependent formulation of viscoplasticity; and development of viscoplastic constitutive model accounting for initial anisotropy
Some advances in experimentation supporting development of viscoplastic constitutive models
The development of a biaxial extensometer capable of measuring axial, torsion, and diametral strains to near-microstrain resolution at elevated temperatures is discussed. An instrument with this capability was needed to provide experimental support to the development of viscoplastic constitutive models. The advantages gained when torsional loading is used to investigate inelastic material response at elevated temperatures are highlighted. The development of the biaxial extensometer was conducted in two stages. The first involved a series of bench calibration experiments performed at room temperature. The second stage involved a series of in-place calibration experiments performed at room temperature. A review of the calibration data indicated that all performance requirements regarding resolution, range, stability, and crosstalk had been met by the subject instrument over the temperature range of interest, 21 C to 651 C. The scope of the in-placed calibration experiments was expanded to investigate the feasibility of generating stress relaxation data under torsional loading
Recommended from our members
Time Resolved Spectroscopy Of Cataclysmic Variables - SS Cygni
NSF AST76-23882, AST 79-06340McDonald Observator
Some advances in experimentation supporting development of viscoplastic constitutive models
The development of a biaxial extensometer capable of measuring axial, torsion, and diametral strains to near-microstrain resolution at elevated temperatures is discussed. An instrument with this capability was needed to provide experimental support to the development of viscoplastic constitutive models. The advantages gained when torsional loading is used to investigate inelastic material response at elevated temperatures are highlighted. The development of the biaxial extensometer was conducted in two stages. The first involved a series of bench calibration experiments performed at room temperature. The second stage involved a series of in-place calibration experiments conducted at room and elevated temperature. A review of the calibration data indicated that all performance requirements regarding resolution, range, stability, and crosstalk had been met by the subject instrument over the temperature range of interest, 21 C to 651 C. The scope of the in-place calibration experiments was expanded to investigate the feasibility of generating stress relaxation data under torsional loading
Experimental determination of flow potential surfaces supporting a multiaxial formulation of viscoplasticity
Details of the experimental procedure followed in a preliminary set of experiments conducted on the representative alloy type 316 stainless steel are given. Although primary interest is in the determination of initial and subsequent surfaces of constant inelastic strain rate (SCISR) at high homologous temperatures (e.g., approx. 0.5). The preliminary tests were conducted at lower temperatures (approx. 0.2) largely because of experimental convenience. Nevertheless, significant time-dependent response at the lower temperature allowed SCISR measurements to be carried out and an evaluation of the experimental technique made. Results of the preliminary tests are presented showing three of a family of initial SCISR's, including strain rate vectors for assessing the condition of normality. Conclusions are drawn concerning the feasibility of the experimental technique, the nature of the measured SCISR's and an assesssment of the normality condition. Finally, a discussion is given of future research
A cost-performance model for ground-based optical communications receiving telescopes
An analytical cost-performance model for a ground-based optical communications receiving telescope is presented. The model considers costs of existing telescopes as a function of diameter and field of view. This, coupled with communication performance as a function of receiver diameter and field of view, yields the appropriate telescope cost versus communication performance curve
A multiaxial theory of viscoplasticity for isotropic materials
Many viscoplastic constitutive models for high temperature structural alloys are based exclusively on uniaxial test data. Generalization to multiaxial states of stress is made by assuming the stress dependence to be on the second principal invariant (J sub 2) of the deviatoric stress, frequently called the effective stress. If such a J sub 2 theory, based on uniaxial testing, is called upon to predict behavior under conditions other than uniaxial, e.g., pure shear, and it does so poorly, nothing is left to adjust in the theory. For a fully isotropic material whose inelastic deformation behavior is relatively independent of hydrostatic stress, the most general stress dependence is on the two (non-zero) principal invariants of the deviatoric stress, J sub 2 and J sub 3. These invariants constitute what is known as an integrity basis for the material. A time dependent constitutive theory with stress dependence on J sub 2 and J sub 3 is presented, that reduces to a known J sub 2 theory as a special case
Follow-up services for improving long-term outcomes in intensive care unit (ICU) survivors
This is a protocol for a Cochrane Review (Intervention). The objectives are as follows:
Our main objective is to assess the effectiveness of follow-up services for ICU survivors that aim to identify and address unmet health needs related to the ICU period. We aim to assess the effectiveness in relation to health-related quality of life, mortality, depression and anxiety, post-traumatic stress disorder, physical function, cognitive function, ability to return to work or education and adverse events.
Our secondary objectives are, in general, to examine both the various ways that follow-up services are provided and any major influencing factors. Specifically, we aim to explore: the effectiveness of service organisation (physician versus nurse led, face to face versus remote, timing of follow-up service); possible differences in services related to country (developed versus developing country); and whether participants had delirium within the ICU setting
- …