5,274 research outputs found
Levitation-melting technique for metals and alloys
Experimentation resulted in an improved levitation-melting technique for metals and alloys which quickly produces a completly homogeneous melt. Also developed were two levitation coils that permit a wide variety of metals to be levitated in the molten state and a helium quenching method which minimizes contamination and segregation
Zero-Gravity Vortex Vent and PVT Gaging System
Space Station and satellite reservicing will require the ability to vent gas on orbit from liquid supply or storage tanks and to gage liquid quantity under microgravity conditions. In zero gravity, (zero-g) the vortex vent is capable of venting gas from a tank of liquid containing gas randomly distributed as bubbles. The concept uses a spinning impeller to create centrifugal force inside a vortex tube within a tank. This creates a gas pocket and forces the liquid through a venturi and back into the tank. Gas is then vented from the gas pocket through a liquid detector and then out through an exhaust port. If the liquid detector senses liquid in the vent line, the fluid is directed to the low-pressure port on the venturi and is returned to the tank. The advantages of this system is that it has no rotating seals and is compatible with most corrosive and cryogenic fluids. A prototype was designed and built at the NASA Johnson Space Center and flown on the KC-135 zero-g aircraft. During these test flights, where microgravity conditions are obtained for up to 30 sec, the prototype demonstrated that less than 0.10 percent of the volume of fluid vented was liquid when the tank was half full of liquid. The pressure volume temperature (PVT) gaging system is used in conjunction with the vortex vent to calculate the amount of liquid remaining in a tank under microgravity conditions. The PVT gaging system is used in conjunction with the vortex vent to gage liquid quantity in zero or low gravity. The system consists of a gas compressor, accumulator, and temperature and pressure instrumentation. To measure the liquid in a tank a small amount of gas is vented from the tank to the compressor and compressed into the accumulator. Pressure and temperature in the tank and accumulator are measured before and after the gas transfer occurs. Knowing the total volume of the tank, the volume of the accumulator, the volume of the intermediate lines, and initial and final pressures and temperatures, the mass of the gas leaving the tank is equated to the mass of the gas entering the accumulator. The volume of liquid remaining in the tank is calculated using the ideal gas law
Tracking Control for FES-Cycling based on Force Direction Efficiency with Antagonistic Bi-Articular Muscles
A functional electrical stimulation (FES)-based tracking controller is
developed to enable cycling based on a strategy to yield force direction
efficiency by exploiting antagonistic bi-articular muscles. Given the input
redundancy naturally occurring among multiple muscle groups, the force
direction at the pedal is explicitly determined as a means to improve the
efficiency of cycling. A model of a stationary cycle and rider is developed as
a closed-chain mechanism. A strategy is then developed to switch between muscle
groups for improved efficiency based on the force direction of each muscle
group. Stability of the developed controller is analyzed through Lyapunov-based
methods.Comment: 8 pages, 4 figures, submitted to ACC201
Refining the scope in computer self-efficacy relationships: an empirical comparison of three instruments in predicting competence and attitudes
Computer self-efficacy (CSE) has been successfully used in many studies as a significant predictor of individual performance and attitudes. However there have been ongoing criticisms concerning selfefficacy’s conceptual foundations as well as its measurement. In the IS field, there have been a number of studies in which the relationship between CSE and consequent behaviors or attitudes was weak or nonexistent. Reasons given for such results include problems associated with the construct of general selfefficacy, and more recently the mismatching of scope (general or specific) between self-efficacy and its predicted outcomes. Little research exists in the IS field to ascertain which instrument is appropriate given the circumstances of the study or to determine if scope plays a significant role in predictability. This study examines three CSE instruments, one general, one global, and one specific (in six domains) in their ability to predict specific and general outcomes (competence and attitudes). The CSE instruments are empirically compared using a sample of 310 ROTC Midshipmen from fourteen universities, using six common computing domains. Results suggest that instrument choice makes a significant difference in predictability and that the alignment in scope of CSE with outcomes is moderated by task mastery in that domain
Crystal structure analysis of intermetallic compounds
Study concerns crystal structures and lattice parameters for a number of new intermetallic compounds. Crystal structure data have been collected on equiatomic compounds, formed between an element of the Sc, Ti, V, or Cr group and an element of the Co or Ni group. The data, obtained by conventional methods, are presented in an easily usable tabular form
MMIC technology for advanced space communications systems
The current NASA program for 20 and 30 GHz monolithic microwave integrated circuit (MMIC) technology is reviewed. The advantages of MMIC are discussed. Millimeter wavelength MMIC applications and technology for communications systems are discussed. Passive and active MMIC compatible components for millimeter wavelength applications are investigated. The cost of a millimeter wavelength MMIC's is projected
Stationary Cycling Induced by Switched Functional Electrical Stimulation Control
Functional electrical stimulation (FES) is used to activate the dysfunctional
lower limb muscles of individuals with neuromuscular disorders to produce
cycling as a means of exercise and rehabilitation. However, FES-cycling is
still metabolically inefficient and yields low power output at the cycle crank
compared to able-bodied cycling. Previous literature suggests that these
problems are symptomatic of poor muscle control and non-physiological muscle
fiber recruitment. The latter is a known problem with FES in general, and the
former motivates investigation of better control methods for FES-cycling.In
this paper, a stimulation pattern for quadriceps femoris-only FES-cycling is
derived based on the effectiveness of knee joint torque in producing forward
pedaling. In addition, a switched sliding-mode controller is designed for the
uncertain, nonlinear cycle-rider system with autonomous state-dependent
switching. The switched controller yields ultimately bounded tracking of a
desired trajectory in the presence of an unknown, time-varying, bounded
disturbance, provided a reverse dwell-time condition is satisfied by
appropriate choice of the control gains and a sufficient desired cadence.
Stability is derived through Lyapunov methods for switched systems, and
experimental results demonstrate the performance of the switched control system
under typical cycling conditions.Comment: 8 pages, 3 figures, submitted to ACC 201
Parameterized Algorithms for Graph Partitioning Problems
We study a broad class of graph partitioning problems, where each problem is
specified by a graph , and parameters and . We seek a subset
of size , such that is at most
(or at least) , where are constants
defining the problem, and are the cardinalities of the edge sets
having both endpoints, and exactly one endpoint, in , respectively. This
class of fixed cardinality graph partitioning problems (FGPP) encompasses Max
-Cut, Min -Vertex Cover, -Densest Subgraph, and -Sparsest
Subgraph.
Our main result is an algorithm for any problem in
this class, where is the maximum degree in the input graph.
This resolves an open question posed by Bonnet et al. [IPEC 2013]. We obtain
faster algorithms for certain subclasses of FGPPs, parameterized by , or by
. In particular, we give an time algorithm for Max
-Cut, thus improving significantly the best known time
algorithm
Conservation for Southern Pulp Mills
Everyone interested in forest conservation is aware of the action recently taken by the Pulp industry of the South through its own organization, the American Pulpwood Association. Not everyone, however, realizes that these conservation steps were conceived and taken by the industry itself
- …