High Dynamic Range RF Front End with Noise Cancellation and Linearization for WiMAX Receivers

This research deals with verification of the high dynamic range for a heterodyne radio frequency (RF) front end. A 2.6 GHz RF front end is designed and implemented in a hybrid microwave integrated circuit (HMIC) for worldwide interoperability for microwave access (WiMAX) receivers. The heterodyne RF front end consists of a low-noise amplifier (LNA) with noise cancellation, an RF bandpass filter (BPF), a downconverter with linearization, and an intermediate frequency (IF) BPF. A noise canceling technique used in the low-noise amplifier eliminates a thermal noise and then reduces the noise figure (NF) of the RF front end by 0.9 dB. Use of a downconverter with diode linearizer also compensates for gain compression, which increases the input-referred third-order intercept point (IIP3) of the RF front end by 4.3 dB. The proposed method substantially increases the spurious-free dynamic range (DRf) of the RF front end by 3.5 dB

Creep recovery and stress relaxation tests of 6061-0 aluminum

The investigation of creep recovery and stress relaxation in aluminum using a closed loop servo-hydraulic test system is described. The practicality of a computer controlled test system for constant plastic strain rate tension tests is demonstrated. The plastic strain rate and the magnitude of the initial strain are shown to have a noticeable effect on subsequent creep behavior of aluminum

A 0.8 V T Network-Based 2.6 GHz Downconverter RFIC

A 2.6 GHz downconverter RFIC is designed and implemented using a 0.18 μm CMOS standard process. An important goal of the design is to achieve the high linearity that is required in WiMAX systems with a low supply voltage. A passive T phase-shift network is used as an RF input stage in a Gilbert cell to reduce supply voltage. A single supply voltage of 0.8 V is used with a power consumption of 5.87 mW. The T network-based downconverter achieves a conversion gain (CG) of 5 dB, a single-sideband noise figure (NF) of 16.16 dB, an RF-to-IF isolation of greater than 20 dB, and an input-referred third-order intercept point (IIP3) of 1 dBm when the LO power of -13 dBm is applied

Precise near-earth navigation with GPS: A survey of techniques

The tracking accuracy of the low earth orbiters (below about 3000 km altitude) can be brought below 10 cm with a variety of differential techniques that exploit the Global Positioning System (GPS). All of these techniques require a precisely known global network of GPS ground receivers and a receiver aboard the user satellite, and all simultaneously estimate the user and GPS satellite orbits. Three basic approaches are the geometric, dynamic, and nondynamic strategies. The last combines dynamic GPS solutions with a geometric user solution. Two powerful extensions of the nondynamic strategy show considerable promise. The first uses an optimized synthesis of dynamics and geometry in the user solution, while the second uses a novel gravity-adjustment method to exploit data from repeat ground tracks. These techniques will offer sub-decimeter accuracy for dynamically unpredictable satellites down to the lowesst possible altitudes

Impact-picture predictions for the γγ\gamma\gamma total cross section at LEP

We show that the rising total cross section $\sigma(\gamma\gamma \to hadrons)$ recently observed by the L3 and OPAL Collaborations at LEP are fully consistent with the impact-picture for high-energy scattering. The impact picture is then used to predict this total cross section at higher energies. These experimental results confirm once more the success of the theoretical approach, which predicted for the first time, nearly thirty years ago, the universal increase of total cross sections at high energies.Comment: 5 pages, Latex, 1 figure. Revised versio

Silicon production in an aerosol reactor

An aerosol reactor system was developed in which large particles of silicon can be grown by silane pyrolysis. To grow particles to sizes larger than one micron, vapor deposition must be used to grow a relatively small number of seed particles. Suppression of nucleation is achieved by limiting the rate of gas phase chemical reactions such that the condensible products of the gas phase chemical reactions diffuse to the surface of the seed particles as rapidly as they are produced. This prevents high degrees of supersaturation and runaway nucleation during the growth process. Particles on the order of 10 microns were grown repeatedly with the present aersol reactor. The nucleation controlled aerosol reactor is, therefore, a suitable system for the production of powders that can readily be separated from the gas by aerodynamic means

Application of Cryogenic Treatment to Extend the Life of the TiAlN-Coated Tungsten Carbide Milling Cutter

Cutting tools are important to the manufacturing industry since they will affect production efficiency and product quality. Cryogenic treatment can improve the material properties by decreasing residual stress, stabilizing dimensional accuracy, and increasing wear resistance. The purpose of this study is to investigate the feasibility and effect of cryogenic treatment on the performance of TiAlN-coated tungsten carbide milling cutters for machining the Inconel alloy 625 in terms of different testing methods (e.g., hardness, wear resistance, residual stress, microstructure, and tool life test). Experimental results indicate that after cryogenic treatment there is less wear, the microstructure is denser, residual stress is decreased, the adhesion of coating and tungsten carbide is improved, and the tool life is effectively improved