High temperature, low-cycle fatigue of copper-base alloys for rocket nozzles. Part 2: Strainrange partitioning and low-cycle fatigue results at 538 deg C

Low-cycle fatigue tests of 1/2 Hard AMZIRC Copper and NARloy Z were performed in argon at 538 C to determine partitioned strain range versus life relationships. Strain-controlled low-cycle fatigue tests of a Zr-Cr-Mg copper-base alloy were also performed. Strain ranges, lower than those employed in previous tests, were imposed in order to extend the fatigue life curve out to approximately 400,000 cycles. An experimental copper alloy and an experimental silver alloy were also studied. Tensile tests were performed in air at room temperature and in argon at 538 C. Strain-controlled low-cycle fatigue tests were performed at 538 C in argon to define the fatigue life over the regime from 300 to 3,000 cycles. For the silver alloy, three additional heat treatments were introduced, and a limited evaluation of the short-term tensile and low-cycle fatigue behavior at 538 C was performed

High temperature, low-cycle fatigue of copper-base alloys in argon. Part 1: Preliminary results for 12 alloys at 1000 F (538 C)

Short-term tensile evaluations at room temperature and 538 C and low-cycle fatigue evaluations at 538 C are presented for the following materials: Zirconium copper-annealed, Zirconium copper-1/4 hard, Zirconium copper-1/2 hard, Tellurium copper-1/2 hard, Chromium copper-SA and aged, OFHC copper-hard, OFHC copper-1/4 hard, OFHC copper-annealed, Silver-as drawn, Zr-Cr-Mg copper-SA, CW and aged, Electroformed copper-30-35 ksi, and Co-Be-Zr- copper-SA, aged. A total of 50 tensile tests and 76 low-cycle fatigue tests were performed using a strain rate of 0.2 percent per second

High temperature, low cycle fatigue of copper-base alloys in argon. Part 3: Zirconium-copper; thermal-mechanical strain cycling, hold-time and notch fatigue results

The low-cycle fatigue characteristics of smooth bar and notched bar specimens (hourglass shape) of zirconium-copper, 1/2 Hard, material (R-2 Series) were evaluated at room temperature in axial strain control. Over the fatigue life range from about 300 to 3000 cycles the ratio of fatigue life for smooth bar to fatigue life for notched bar remained constant at a value of about 6.0. Some additional hold-time data for the R-2 alloy tested in argon at 538 C are reported. An analysis of the relaxation data obtained in these hold-time tests is also reported and it is shown that these data yield a fairly consistent correlation in terms of instantaneous stress rate divided by instantaneous stress. Two thermal-mechanical strain cycling tests were also performed using a cyclic frequency of 4.5 cycles per hour and a temperature cycling interval from 260 to 538 C. The fatigue life values in these tests were noticeably lower than that observed in isothermal tests at 538 C

High-temperature, low-cycle fatigue of advanced copper-base alloys for rocket nozzles. Part 1: Narloy Z

Short-term tensile and low-cycle fatigue data are reported for Narloy Z, a centrifugally cast, copper-base alloy. Tensile tests were performed at room temperature in air and in argon at 482, 538 and 593 C using an axial strain rate of .002/sec to the -1 power. In addition tensile tests were performed at 538 C in an evaluation of tensile properties at strain rates of .004 and .01/sec to the -1 power. Ultimate and yield strength values of about 315 and 200 MN/sq m respectively were recorded at room temperature and these decreased to about 120 and 105 respectively as the temperature was increased to 593 C. Reduction in area values were recorded in the range from 40 to 50% with some indication of a minimum ductility point at 538 C

High-temperature, low-cycle fatigue of advanced copper-base alloys for rocket nozzles. Part 2: NASA 1.1, Glidcop, and sputtered copper alloys

Short-term tensile and low-cycle fatigue data are reported for five advance copper-base alloys: Sputtered Zr-Cu as received, sputtered Zr-Cu heat-treated, Glidcop AL-10, and NASA alloys 1-1A and 1-1B. Tensile tests were performed in argon at 538 C using an axial strain rate of 0.002/sec. Yield strength and ultimate tensile strength data are reported along with reduction in area values. Axial strain controlled low-cycle fatigue tests were performed in argon at 538C using an axial strain rate of 0.002/sec to define the fatigue life over the range from 100 to 3000 cycles for the five materials studied. It was found that the fatigue characteristics of the NASA 1-1A and NASA 1-1B compositions are identical and represent fatique life values which are much greater than those for the other materials tested. The effect of temperature on NASA 1-1B alloy at a strain rate of 0.002/sec was evaluated along with the effect of strain rates of 0.0004 and 0.01/sec at 538 C. Hold-time data are reported for the NASA 1-1B alloy at 538 C using 5 minute hold periods in tension only and compression only at two different strain range values. Hold periods in tension were much more detrimental than hold periods in compression

Direct observation of voids in the vacancy excess region of ion bombarded silicon

The results reported in this letter indicate that the spatial separation of the vacancy and interstitial excesses which result from ion bombardment gives rise to stable voids upon annealing at 850 °C even for implants where the projected ion range is only of the order of a few thousand Ångstrom. Such voids have been observed directly by transmission electron microscopy. Furthermore, in cases where both voids and interstitial-based defects are present at different depths, it is found that Au has a strong preference for decorating void surfaces and hence Au can, indeed, be used as a selective detector of open volume defects in Si.One of the authors ~J.W.-L.! acknowledges the Australian Research Council for financial support

86 GHz Very Long Baseline Polarimetry of 3C273 and 3C279 with the Coordinated Millimeter VLBI Array

86 GHz Very Long Baseline Polarimetry probes magnetic field structures within the cores of Active Galactic Nuclei at higher angular resolutions and a spectral octave higher than previously achievable. Observations of 3C273 and 3C279 taken in April 2000 with the Coordinated Millimeter VLBI Array have resulted in the first total intensity (Stokes I) and linear polarization VLBI images reported of any source at 86 GHz. These results reveal the 86 GHz electric vector position angles within the jets of 3C273 and 3C279 to be orthogonal to each other, and the core of 3C273 to be unpolarized. If this lack of polarization is due to Faraday depolarization alone, the dispersion in rotation measure is >=90000 rad/m^2 for the core of 3C273.Comment: AASTeX v5.02; 10 pages; 4 figures; accepted for publication in the Astrophysical Journal Letter

Electrostatic interactions mediated by polarizable counterions: weak and strong coupling limits

We investigate the statistical mechanics of an inhomogeneous Coulomb fluid composed of charged particles with static polarizability. We derive the weak- and the strong-coupling approximations and evaluate the partition function in a planar dielectric slab geometry with charged boundaries. We investigate the density profiles and the disjoining pressure for both approximations. Comparison to the case of non-polarizable counterions shows that polarizability brings important differences in the counterion density distribution as well as the counterion mediated electrostatic interactions between charged dielectric interfaces.Comment: 25 pages, 7 figure

Icelandic debris flow and their relationship to martian gullies

Abstract not available

Delineation of precipitation areas from MODIS visible and infrared imagery with artificial neural networks

An important phase in a nowcasting system is the diagnosis of the forecast variables. This work focuses on the diagnosis of precipitation. The Nimrod automatic nowcasting system at the Met Office (UK) has long used Meteosat visible and infrared data to supplement the data it receives from the UK weather radar network to produce rainfall analyses. With the advent of Meteosat Second Generation (MSG) attention has focused on how best to use the larger range of spectral information from MSG to improve the rainfall analyses. Earlier work at the Met Office had suggested artificial neural networks (ANNs) to be a useful tool for such applications. Pending the availability of data from MSG, ANNs were used to process data from appropriate visible and infrared channels on the MODIS instrument. Sixty daytime winter cases were collected, and Nimrod radar rainfall analyses provided 'ground truth' for both training and testing the ANNs. The optimal combination of MODIS channels was investigated and it was found that almost all the skill in rain/no rain discrimination was provided by the radiance values from six selected spectral channels. A notable result was that the 1.64 µm channel had no value as a discriminator when used alone, but produced a large increase in skill when used in conjunction with a visible channel. The ANN with MODIS data was found to outperform the corresponding Nimrod look-up table technique applied to Meteosat data. Application of the technique to SEVIRI data is proposed, as is extension to other seasons. Copyright © 2005 Royal Meteorological Societ