1,720 research outputs found
Multicast using PIM-SM in Broadband Satellite Multimedia Systems
The approach currently being taken by ETSI (BSM) to standardisation for Multicast PIM-SM protocols is described. This paper describes methods, architectures and adaptations to support IP-multicast services efficiently across IP-based broadband multimedia satellite systems. This work has recently begun and the final objective is to arrive at a consensus for a standard on this subject
Aerodynamic design guidelines and computer program for estimation of subsonic wind tunnel performance
General guidelines are given for the design of diffusers, contractions, corners, and the inlets and exits of non-return tunnels. A system of equations, reflecting the current technology, has been compiled and assembled into a computer program (a user's manual for this program is included) for determining the total pressure losses. The formulation presented is applicable to compressible flow through most closed- or open-throat, single-, double-, or non-return wind tunnels. A comparison of estimated performance with that actually achieved by several existing facilities produced generally good agreement
Wind sensitivity studies of a non-return wind tunnel with a 216- by 432-mm (8.5- by 17.0-inches) test section, phase 2
The refinement of inlet and exit treatments were studied which would minimize the effect of external wind on the test-section flow quality of a nonreturn wind tunnel. The investigation was conducted in the Ames Research Center 40- by 80-foot Wind Tunnel which served as the wind source. Several inlets and two exits were tested at wind directions ranging from 0 to 180 degrees and at wind-to-test-section velocity ratios from zero to somewhat greater than one. For the best inlet configuration the flow quality was good, with a velocity deviation in each of the three component directions generally less. The loss in total pressure due to the inlet treatment was low: about 0.035 of the test-section dynamic pressure for the no-wind case
Wind sensitivity studies of a non-return wind tunnel, with a 216- by 432-mm (8.5- by 17.0-inch) test section, phase 1
The study to develop inlet and exit treatments which would minimize the effect of external wind on the test-section flow quality of a nonreturn wind tunnel is reported. The investigation was conducted in the Ames Research Center 40- by 80-Foot Wind Tunnel which served as the wind source. Several inlets and two exits were tested at wind directions ranging from 0 to 180 degrees and at wind-to-test-section velocity ratios between zero and one. For the best inlet configuration the flow quality was good, with a velocity deviation in each of the three directions generally less than 1/2 knot (0.26 m/sec) for wind velocities of 15 knots (7.7 m/sec) or less. The loss in total pressure due to the inlet treatment was low: about 0.03 of the test-section dynamic pressure
MINERAL RIGHTS IN LOUISIANA, by Harriet Spiller Daggett. Louisiana State University Press, University, 1939. Pp. xxxv, 427. $5.00.
A facial expression for anxiety.
Anxiety and fear are often confounded in discussions of human emotions. However, studies of rodent defensive reactions under naturalistic conditions suggest anxiety is functionally distinct from fear. Unambiguous threats, such as predators, elicit flight from rodents (if an escape-route is available), whereas ambiguous threats (e.g., the odor of a predator) elicit risk assessment behavior, which is associated with anxiety as it is preferentially modulated by anti-anxiety drugs. However, without human evidence, it would be premature to assume that rodent-based psychological models are valid for humans. We tested the human validity of the risk assessment explanation for anxiety by presenting 8 volunteers with emotive scenarios and asking them to pose facial expressions. Photographs and videos of these expressions were shown to 40 participants who matched them to the scenarios and labeled each expression. Scenarios describing ambiguous threats were preferentially matched to the facial expression posed in response to the same scenario type. This expression consisted of two plausible environmental-scanning behaviors (eye darts and head swivels) and was labeled as anxiety, not fear. The facial expression elicited by unambiguous threat scenarios was labeled as fear. The emotion labels generated were then presented to another 18 participants who matched them back to photographs of the facial expressions. This back-matching of labels to faces also linked anxiety to the environmental-scanning face rather than fear face. Results therefore suggest that anxiety produces a distinct facial expression and that it has adaptive value in situations that are ambiguously threatening, supporting a functional, risk-assessing explanation for human anxiet
Geometry dependence of the clogging transition in tilted hoppers
We report the effect of system geometry on the clogging of granular material
flowing out of flat-bottomed hoppers with variable aperture size D. For such
systems, there exists a critical aperture size Dc at which there is a
divergence in the time for a flow to clog. To better understand the origins of
Dc, we perturb the system by tilting the hopper an angle Q and mapping out a
clogging phase diagram as a function of Q and D. The clogging transition
demarcates the boundary between the freely-flowing (large D, small Q) and
clogging (small D, large Q) regimes. We investigate how the system geometry
affects Dc by mapping out this phase diagram for hoppers with either a circular
hole or a rectangular narrow slit. Additionally, we vary the grain shape,
investigating smooth spheres (glass beads), compact angular grains (beach
sand), disk-like grains (lentils), and rod-like grains (rice). We find that the
value of Dc grows with increasing Q, diverging at pi-Qr where Qr is the angle
of repose. For circular apertures, the shape of the clogging transition is the
same for all grain types. However, this is not the case for the narrow slit
apertures, where the rate of growth of the critical hole size with tilt angle
depends on the material
- …