Description of a digital computer simulation of an Annular Momentum Control Device (AMCD) laboratory test model

A description of a digital computer simulation of an Annular Momentum Control Device (AMCD) laboratory model is presented. The AMCD is a momentum exchange device which is under development as an advanced control effector for spacecraft attitude control systems. The digital computer simulation of this device incorporates the following models: six degree of freedom rigid body dynamics; rim warp; controller dynamics; nonlinear distributed element axial bearings; as well as power driver and power supply current limits. An annotated FORTRAN IV source code listing of the computer program is included

Signatures of Hong-Ou-Mandel Interference at Microwave Frequencies

Two-photon quantum interference at a beam splitter, commonly known as Hong-Ou-Mandel interference, was recently demonstrated with \emph{microwave-frequency} photons by Lang \emph{et al.}\,\cite{lang:microwaveHOM}. This experiment employed circuit QED systems as sources of microwave photons, and was based on the measurement of second-order cross-correlation and auto-correlation functions of the microwave fields at the outputs of the beam splitter. Here we present the calculation of these correlation functions for the cases of inputs corresponding to: (i) trains of \emph{pulsed} Gaussian or Lorentzian single microwave photons, and (ii) resonant fluorescent microwave fields from \emph{continuously-driven} circuit QED systems. The calculations include the effects of the finite bandwidth of the detection scheme. In both cases, the signature of two-photon quantum interference is a suppression of the second-order cross-correlation function for small delays. The experiment described in Ref. \onlinecite{lang:microwaveHOM} was performed with trains of \emph{Lorentzian} single photons, and very good agreement between the calculations and the experimental data was obtained.Comment: 11 pages, 3 figure

Propagation of sound through a sheared flow

Sound generated in a moving fluid must propagate through a shear layer in order to be measured by a fixed instrument. These propagation effects were evaluated for noise sources typically associated with single and co-flowing subsonic jets and for subcritical flow over airfoils in such jets. The techniques for describing acoustic propagation fall into two categories: geometric acoustics and wave acoustics. Geometric acoustics is most convenient and accurate for high frequency sound. In the frequency range of interest to the present study (greater than 150 Hz), the geometric acoustics approach was determined to be most useful and practical

Analysis and simulation of a magnetic bearing suspension system for a laboratory model annular momentum control device

A linear analysis and the results of a nonlinear simulation of a magnetic bearing suspension system which uses permanent magnet flux biasing are presented. The magnetic bearing suspension is part of a 4068 N-m-s (3000 lb-ft-sec) laboratory model annular momentum control device (AMCD). The simulation includes rigid body rim dynamics, linear and nonlinear axial actuators, linear radial actuators, axial and radial rim warp, and power supply and power driver current limits

Continuous quantum non-demolition measurement of Fock states of a nanoresonator using feedback-controlled circuit QED

We propose a scheme for the quantum non-demolition (QND) measurement of Fock states of a nanomechanical resonator via feedback control of a coupled circuit QED system. A Cooper pair box (CPB) is coupled to both the nanoresonator and microwave cavity. The CPB is read-out via homodyne detection on the cavity and feedback control is used to effect a non-dissipative measurement of the CPB. This realizes an indirect QND measurement of the nanoresonator via a second-order coupling of the CPB to the nanoresonator number operator. The phonon number of the Fock state may be determined by integrating the stochastic master equation derived, or by processing of the measurement signal.Comment: 5 pages, 3 figure

Evaluation of the 50km/h default urban speed limit in South Australia

On the 1st March 2003 the Default Urban Speed Limit (DUSL) in South Australia was lowered from 60 km/h to 50 km/h. Since this date, all urban roads have a speed limit of 50 km/h unless otherwise signed. This paper reports the results of an evaluation of the effectiveness of the reduced DUSL and is based on speed surveys and crash data analysis. Vehicles speeds were measured at 52 randomly chosen sites across the State. Crash data was analysed by examining the crash history of all roads with a 50 km/h or 60 km/h speed limit, a year before and after the new DUSL was introduced. The study found that, on average, mean speeds have fallen by approximately 2.2 km/h on streets where the speed limit was reduced and by 0.7 km/h on arterial roads where 60 km/h speed limit signs were erected. There was a 19.8% reduction in casualty crashes on 50 km/h roads and a corresponding 4.6% reduction on 60 km/h arterial roads when compared with the previous year.C. Kloeden, J. Woolley and J. McLea

Delta-Vs and Design Reference Mission Scenarios for Mars Missions

Before setting out on any long journey, it is important to first have an idea about how to get there, how long it might take, and how much it will cost. Primarily, the answers depend upon where you are starting and where you wish to go. In the formulative stages of any mission to Mars, having quick estimates of answers to these basic questions will aid in the efficient exploration of the trade space. In this paper, we present a “mileage chart” of sorts illustrating the range of ΔV’s and times-of-flight (TOF) between various starting and stopping points between Earth and Mars. This paper expands upon a chart from a previous work by the authors. We discuss the methodologies used to calculate or estimate expected values and reasonable ranges, including some more detailed specific examples

Count three for wear able computers

This paper is a postprint of a paper submitted to and accepted for publication in the Proceedings of the IEE Eurowearable 2003 Conference, and is subject to Institution of Engineering and Technology Copyright. The copy of record is available at the IET Digital Library. A revised version of this paper was also published in Electronics Systems and Software, also subject to Institution of Engineering and Technology Copyright. The copy of record is also available at the IET Digital Library.A description of 'ubiquitous computer' is presented. Ubiquitous computers imply portable computers embedded into everyday objects, which would replace personal computers. Ubiquitous computers can be mapped into a three-tier scheme, differentiated by processor performance and flexibility of function. The power consumption of mobile devices is one of the most important design considerations. The size of a wearable system is often a design limitation