High-Speed Monitoring of Dust Particles in ITER ELMs Simulation Experiments with QSPA Kh-50

Dust generation under powerful plasma stream impacts has been studied in ITER ELM simulation experiments with QSPA Kh-50 plasma accelerator. Repetitive plasma exposures of tungsten have been performed by 0.25 ms plasma pulses and the heat load varied in the range (0.1÷1.1) MJm-2. Main characteristics of dust particles such as a number of ejected particles, their velocity, angular distribution and start time from the surface are investigated. Dust particles have not been observed under heat load below the cracking threshold. Quantity of dust particles rises with increasing heat load. Average velocities of dust particles are found to be strongly dependent on their start time from the surface after beginning of plasma-surface interaction. Maximal velocity achieved a few tens of meters per second

Local Magnetohydrodynamic Characteristics of the Plasma Stream generated by MPC

This paper investigates the spatial distributions of electrical current which flows inside the plasma stream generated by a magnetoplasma compressor (MPC). Two different modes of MPC operation with different gas supply scenarios have been applied in the experiments presented here. The first is the operation mode with a pulse injection of xenon into the interelectrode space, and the second is the operation mode with residual helium in the chamber and local injection of xenon directly into the compression zone. The maximum value of the electric current observed outside the MPC channel is 15 ÷ 20% of the total discharge current. Electric current vortices were discovered in the plasma stream. The amplitude of the current in the vortices reaches 50% of the total discharge current. The maximum EUV radiation power was measured in the mode of MPC operation with local xenon injection. Power in the wave range 12.2 ÷ 15.8 nm achieves up to 16 ÷ 18 kW

Local Magnetohydrodynamic Characteristics of the Plasma Stream generated by MPC

This paper investigates the spatial distributions of electrical current which flows inside the plasma stream generated by a magnetoplasma compressor (MPC). Two different modes of MPC operation with different gas supply scenarios have been applied in the experiments presented here. The first is the operation mode with a pulse injection of xenon into the interelectrode space, and the second is the operation mode with residual helium in the chamber and local injection of xenon directly into the compression zone. The maximum value of the electric current observed outside the MPC channel is 15 ÷ 20% of the total discharge current. Electric current vortices were discovered in the plasma stream. The amplitude of the current in the vortices reaches 50% of the total discharge current. The maximum EUV radiation power was measured in the mode of MPC operation with local xenon injection. Power in the wave range 12.2 ÷ 15.8 nm achieves up to 16 ÷ 18 kW

Non-self-sustained discharge with hollow anode for plasma-based surface treatment

The paper discusses plasma methods for surface modification using the non-self-sustained glow discharge with a hollow anode. This discharge is characterised by low voltage and high values of electron and ion currents. It can be easily excited in vacuum-arc installations that are widely used for coatings deposition. It is shown that such type of discharge may be effectively used for ion pumping, film deposition, ion etching, diffusion saturation of metallic materials, fusion and brazing of metals, and for combined application of above mentioned technologies in a single vacuum cycle

Plasma exposure of different tungsten grades with plasma accelerators under ITER-relevant conditions

This paper presents the results of tungsten irradiation experiments performed with three plasma facilities: the QSPA Kh-50 quasi-steady-state plasma accelerator, the PPA pulsed plasma gun and the magneto-plasma compressor. Targets made of different kinds of tungsten (sintered, rolled and deformed) were irradiated with powerful plasma streams at heat fluxes relevant to edge-localized modes in ITER. The irradiated targets were analyzed and two different meshes of cracks were identified. It has been shown that the major cracks do not depend on the tungsten grade. This has been attributed to ductile-to-brittle transition effects. Meshes of inter-granular micro-cracks were detected for energy loads above the melting threshold and these were probably caused by the re-solidification process. The blister-like and cellular-like structures were observed on sample surfaces exposed to helium and hydrogen plasmas

Studies of plasma interactions with tungsten targets in PF-1000U facility

This paper presents results of experimental studies of tungsten samples of 99.95% purity, which were irradiated by intense plasma-ion streams. The behaviour of tungsten, and particularly its structural change induced by high plasma loads, is of great importance for fusion technology. The reported measurements were performed within a modified PF-1000U plasma-focus facility operated at the IFPiLM in Warsaw, Poland. The working gas was pure deuterium. In order to determine the main plasma parameters and to study the behaviour of impurities at different instants of the plasma discharge, the optical emission spectroscopy was used. The dependence of plasma parameters on the initial charging voltage (16, 19 and 21 kV) was studied. Detailed optical measurements were performed during interactions of a plasma stream with the tungsten samples placed at the z-axis of the facility, at a distance of 6 cm from the electrode outlets. The recorded spectra showed distinct WI and WII spectral lines. Investigation of a target surface morphology, after its irradiation by intense plasma streams, was performed by means of an optical microscope. The observations revealed that some amounts of the electrodes material (mainly copper) were deposited upon the irradiated sample surface. In all the cases, melted zones were observed upon the irradiated target surface, and in experiments performed at the highest charging voltage there were formed some cracks

ICRF Plasma Production with Hydrogen Minority Heating in Uragan-2M and Large Helical Device

ORCID　0000-0003-4948-0896This report compares results ion-cyclotron range of frequencies (ICRF) plasma production at hydrogen minority regime in Uragan-2M (U-2M) and Large Helical Device (LHD). The condition of the presence of the fundamental harmonic ion cyclotron resonance zone for the hydrogen inside the plasma column should be fulfilled for this method. The scenario is successful at both machines and weakly sensitive to the variation of the hydrogen concentration in the H2+He gas mixture. It should be noted that at LHD the start up is slower than at U-2M. The comparison of plasma production in ICRF with hydrogen minority at U-2M and LHD indicate that this scenario can be scaled to larger stellarator devices. The experiments made are the base for the proposal for usage this scenario for plasma production in ICRF at Wendelstein 7-X at magnetic field reduced to 1.7 T

Study of tungsten surface interaction with plasma streams at DPF-1000U

In this note experimental studies of tungsten (W) samples irradiated by intense plasma-ion streams are reported. Measurements were performed using the modified plasma focus device DPF-1000U equipped with an axial gas-puffing system. The main diagnostic tool was a Mechelle®900 optical spectrometer. The electron density of a freely propagating plasma stream (i.e., the plasma stream observed without any target inside the vacuum chamber) was estimated on the basis of the half-width of the Dβ spectral line, taking into account the linear Stark effect. For a freely propagating plasma stream the maximum electron density amounted to about 1.3 × 1017 cm−3 and was reached during the maximum plasma compression. The plasma electron density depends on the initial conditions of the experiments. It was thus important to determine first the plasma flow characteristics before attempting any target irradiation. These data were needed for comparison with plasma characteristics after an irradiation of the investigated target. In fact, spectroscopic measurements performed during interactions of plasma streams with the investigated W samples showed many WI and WII spectral lines. The surface erosion was determined from mass losses of the irradiated samples. Changes on the surfaces of the irradiated samples were also investigated with an optical microscope and some sputtering and melting zones were observed