5 research outputs found

    Enhanced two-terminal impedance-based fault location using sequence values

    Get PDF
    Fault at transmission line system may lead to major impacts such as power quality problems and cascading failure in the grid system. Thus, it is very important to locate it fast so that suitable solution can be taken to ensure power system stability can be retained. The complexity of the transmission line however makes the fault point identification a challenging task. This paper proposes an enhanced fault detection and location method using positive and negative-sequence values of current and voltage, taken at both local and remote terminals. The fault detection is based on comparison between the total fault current with currents combination during the pre-fault time. While the fault location algorithm was developed using an impedance-based method and the estimated fault location was taken at two cycles after fault detection. Various fault types, fault resistances and fault locations have been tested in order to verify the performance of the proposed method. The developed algorithms have successfully detected all faults within high accuracy. Based on the obtained results, the estimated fault locations are not affected by fault resistance and line charging current. Furthermore, the proposed method able to detect fault location without the needs to know the fault type

    Differential equation fault location algorithm with harmonic effects in power system

    Get PDF
    About 80% of faults in the power system distribution are earth faults. Studies to find effective methods to identify and locate faults in distribution networks are still relevant, in addition to the presence of harmonic signals that distort waves and create deviations in the power system that can cause many problems to the protection relay. This study focuses on a single line-to-ground (SLG) fault location algorithm in a power system distribution network based on fundamental frequency measured using the differential equation method. The developed algorithm considers the presence of harmonics components in the simulation network. In this study, several filters were tested to obtain the lowest fault location error to reduce the effect of harmonic components on the developed fault location algorithm. The network model is simulated using the alternate transients program (ATP)Draw simulation program. Several fault scenarios have been implemented during the simulation, such as fault resistance, fault distance, and fault inception angle. The final results show that the proposed algorithm can estimate the fault distance successfully with an acceptable fault location error. Based on the simulation results, the differential equation continuous wavelet technique (CWT) filter-based algorithm produced an accurate fault location result with a mean average error (MAE) of less than 5%

    Mathematical Derivation of Switching Angles of Multilevel Voltage Source Inverter based on Alternative Phase Opposition Disposition (APOD)

    No full text
    Modular structured multilevel inverter is very useful for electrical application especially in high voltage and high power applications. The main function of this multilevel inverter is to produce multilevel AC output voltage from several separate DC sources. This project is to derive a newmathematical formulation of multilevel voltage source inverter switching instants. The proposed method for this project is based on the sinusoidal natural sampling PWM (SPWM) by comparing several modified modulation signal with a triangular carrier signal. This resulting intersection points between this modulation and carrier signal become the switching instants of the PWM pulses. Derivation also based on Alternative Phase opposition disposition (APOD). A cascaded multilevel inverter is selected as a topology for this project due to major advantages compare with other topology. The derived formula is analyzed by using MATLAB simulation software. It is found that the results that use the derived formula are almost identical to simulation result

    Mathematical Derivation of Switching Angles of Multilevel Voltage Source Inverter based on Alternative Phase Opposition Disposition (APOD)

    Get PDF
    Modular structured multilevel inverter is very useful for electrical application especially in high voltage and high power applications. The main function of this multilevel inverter is to produce multilevel AC output voltage from several separate DC sources. This project is to derive a newmathematical formulation of multilevel voltage source inverter switching instants. The proposed method for this project is based on the sinusoidal natural sampling PWM (SPWM) by comparing several modified modulation signal with a triangular carrier signal. This resulting intersection points between this modulation and carrier signal become the switching instants of the PWM pulses. Derivation also based on Alternative Phase opposition disposition (APOD). A cascaded multilevel inverter is selected as a topology for this project due to major advantages compare with other topology. The derived formula is analyzed by using MATLAB simulation software. It is found that the results that use the derived formula are almost identical to simulation result
    corecore