46 research outputs found
Work status of 5 MeV 300 kW electron accelerator
Design work has been completed for the accelerating structure of high-power electron accelerator with 5 MeV,
300 kW, 176 MHz parameters. The structure is being produced in BINP workshop. The paper presents the design of
the accelerating structure which consists of a chain of coaxial cavities, and block diagram of experimental
workbench. Structure of the main accelerator blocks and their degree of fabrication are viewed.Закончены проектные работы по ускоряющей структуре мощного электронного ускорителя 5 МэВ,
300 кВт, 176 МГц и ведется ее изготовление в опытном производстве Института. Дается описание
конструкции ускоряющей структуры, состоящей из цепочки связанных коаксиальных резонаторов.
Приводится блок-схема испытательного стенда, рассматривается устройство отдельных узлов ускорителя и
состояние их готовности.Закінчено проектні роботи із прискорювальної структури потужного електронного прискорювача 5 МеВ,
300 кВт, 176 МГц і ведеться її виготовлення в дослідному виробництві інституту. Дається опис конструкції
прискорювальної структури, що складається з ланцюжка зв'язаних коаксіальних резонаторів. Приводиться
блок-схема іспитового стенда, розглядається будова окремих вузлів прискорювача і стан їх готовності
Measurement of and between 3.12 and 3.72 GeV at the KEDR detector
Using the KEDR detector at the VEPP-4M collider, we have measured
the values of and at seven points of the center-of-mass
energy between 3.12 and 3.72 GeV. The total achieved accuracy is about or
better than at most of energy points with a systematic uncertainty of
about . At the moment it is the most accurate measurement of in
this energy range
New precise determination of the \tau lepton mass at KEDR detector
The status of the experiment on the precise lepton mass measurement
running at the VEPP-4M collider with the KEDR detector is reported. The mass
value is evaluated from the cross section behaviour around the
production threshold. The preliminary result based on 6.7 pb of data is
MeV. Using 0.8 pb of data
collected at the peak the preliminary result is also obtained:
eV.Comment: 6 pages, 8 figures; The 9th International Workshop on Tau-Lepton
Physics, Tau0
Measurement of \Gamma_{ee}(J/\psi)*Br(J/\psi->e^+e^-) and \Gamma_{ee}(J/\psi)*Br(J/\psi->\mu^+\mu^-)
The products of the electron width of the J/\psi meson and the branching
fraction of its decays to the lepton pairs were measured using data from the
KEDR experiment at the VEPP-4M electron-positron collider. The results are
\Gamma_{ee}(J/\psi)*Br(J/\psi->e^+e^-)=(0.3323\pm0.0064\pm0.0048) keV,
\Gamma_{ee}(J/\psi)*Br(J/\psi->\mu^+\mu^-)=(0.3318\pm0.0052\pm0.0063) keV.
Their combinations
\Gamma_{ee}\times(\Gamma_{ee}+\Gamma_{\mu\mu})/\Gamma=(0.6641\pm0.0082\pm0.0100)
keV,
\Gamma_{ee}/\Gamma_{\mu\mu}=1.002\pm0.021\pm0.013 can be used to improve
theaccuracy of the leptonic and full widths and test leptonic universality.
Assuming e\mu universality and using the world average value of the lepton
branching fraction, we also determine the leptonic \Gamma_{ll}=5.59\pm0.12 keV
and total \Gamma=94.1\pm2.7 keV widths of the J/\psi meson.Comment: 7 pages, 6 figure
Industrial electron accelerators type ILU
The paper describes ILU type industrial electron accelerators. Their main parameters, design, principle of action,
electron beam extraction devices, wide set of auxiliary equipment for various technological processes and ways of
their usage are discussed as well.Описаны промышленные ускорители электронов серии ИЛУ. Приведены основные параметры,
устройство и принцип действия. Дается краткое описание систем выпуска ускоренного пучка в атмосферу
для различных технологических процессов.Описано промислові прискорювачі електронів серії ЫЛП. Наведено основні параметри, будова і
принцип дії. Дається короткий опис систем випуску прискореного пучку в атмосферу для різних
технологічних процесів