Experimental study exploring the factors that promote rib fragility in the elderly

Rib fractures represent a common injury type due to blunt chest trauma, affecting hospital stay and mortality especially in elderly patients. Factors promoting rib fragility, however, are little investigated. The purpose of this in vitro study was to explore potential determinants of human rib fragility in the elderly. 89 ribs from 13 human donors (55\u201399 years) were loaded in antero-posterior compression until fracture using a material testing machine, while surface strains were captured using a digital image correlation system. The effects of age, sex, bone mineral density, rib level and side, four global morphological factors (e.g. rib length), and seven rib cross-sectional morphological factors (e.g. cortical thickness, determined by \u3bcCT), on fracture load were statistically examined using Pearson correlation coefficients, Mann\u2013Whitney U test as well as Kruskal\u2013Wallis test with Dunn-Bonferroni post hoc correction. Fracture load showed significant dependencies (p < 0.05) from bone mineral density, age, antero-posterior rib length, cortical thickness, bone volume/tissue volume ratio, trabecular number, trabecular separation, and both cross-sectional area moments of inertia and was significantly higher at rib levels 7 and 8 compared to level 4 (p = 0.001/0.013), whereas side had no significant effect (p = 0.989). Cortical thickness exhibited the highest correlation with fracture load (r = 0.722), followed by the high correlation of fracture load with the area moment of inertia around the longitudinal rib cross-sectional axis (r = 0.687). High correlations with maximum external rib surface strain were detected for bone volume/tissue volume ratio (r = 0.631) and trabecular number (r = 0.648), which both also showed high correlations with the minimum internal rib surface strain (r = 12 0.644/ 12 0.559). Together with rib level, the determinants cortical thickness, area moment of inertia around the longitudinal rib cross-sectional axis, as well as bone mineral density exhibited the largest effects on human rib fragility with regard to the fracture load. Sex, rib cage side, and global morphology, in contrast, did not affect rib fragility in this study. When checking elderly patients for rib fractures due to blunt chest trauma, patients with low bone mineral density and the mid-thoracic area should be carefully examined

Direct Josephson coupling between superconducting flux qubits

We have demonstrated strong antiferromagnetic coupling between two three-junction flux qubits based on a shared Josephson junction, and therefore not limited by the small inductances of the qubit loops. The coupling sign and magnitude were measured by coupling the system to a high-quality superconducting tank circuit. Design modifications allowing to continuously tune the coupling strength and/or make the coupling ferromagnetic are discussed.Comment: REVTeX 4, 4 pages, 5 figures; v2: completely rewritten, added finite-temperature results and proposals for ferromagnetic galvanic couplin

Geometric observation for the Bures fidelity between two states of a qubit

In this Brief Report, we present a geometric observation for the Bures fidelity between two states of a qubit.Comment: 4 pages, 1 figure, RevTex, Accepted by Phys. Rev.

Investigations on fluid dynamics of hydraulic accumulators

In state of the art hydrostatic installations accumulators of various designs are implemented to enhance the efficiency or to affect the dynamics of the hydraulic system. The advantages offered by the application of these devices are well known and their thermodynamic properties have been described well in the past. Yet the optimization of their particular performance re-garding fluid dynamics is an existing problem because of the lack of experimental and analytical investigation devices. Whilst operating hydraulic accumulators high dynamic flow rates and velocities including steep pressure gradients are oc-curring so that a special technique had to be created to detect these values. In the Fluid Power Laboratory of Trier University of Ap-plied Sciences a new self developed accumulator test rig re-cently was installed to measure the operating parameters of hy-draulic accumulators with the required high dynamic and accuracy. Special test procedures could be implemented to evaluate and improve especially the performance of the accu-mulators internal flow control valves. The experimental investigations were accompanied by modelling a hydraulic accumulator in a Computational Fluid Dynamic CFD environment where its internal flow phenomena could be simulated successfully. This presentation introduces the new test rig, the developed measuring procedures and the simulation model. Results of high dynamic flow and pressure measurements as well as flow simulations of hydraulic accumulators are shown.Papers presented to the 12th International Conference on Heat Transfer, Fluid Mechanics and Thermodynamics, Costa de Sol, Spain on 11-13 July 2016

Fatigue analysis-based numerical design of stamping tools made of cast iron

This work concerns stress and fatigue analysis of stamping tools made of cast iron with an essentially pearlitic matrix and containing foundry defects. Our approach consists at first, in coupling the stamping numerical processing simulations and structure analysis in order to improve the tool stiffness geometry for minimizing the stress state and optimizing their fatigue lifetime. The method consists in simulating the stamping process by considering the tool as a perfect rigid body. The estimated contact pressure is then used as boundary condition for FEM structure loading analysis of the tool. The result of this analysis is compared with the critical stress limit depending on the automotive model. The acceptance of this test allows calculating the fatigue lifetime of the critical zone by using the S–N curve of corresponding load ratio. If the prescribed tool life requirements are not satisfied, then the critical region of the tool is redesigned and the whole simulation procedures are reactivated. This method is applied for a cast iron EN-GJS-600-3. The stress-failure (S–N) curves for this material is determined at room temperature under push pull loading with different load ratios R0σmin/σmax0−2, R0−1 and R00.1. The effects of the foundry defects are determined by SEM observations of crack initiation sites. Their presence in tested specimens is associated with a reduction of fatigue lifetime by a factor of 2. However, the effect of the load ratio is more important