Theory of the collapsing axisymmetric cavity

We investigate the collapse of an axisymmetric cavity or bubble inside a fluid of small viscosity, like water. Any effects of the gas inside the cavity as well as of the fluid viscosity are neglected. Using a slender-body description, we show that the minimum radius of the cavity scales like $h_0 \propto t'^{\alpha}$, where $t'$ is the time from collapse. The exponent $\alpha$ very slowly approaches a universal value according to $\alpha=1/2 + 1/(4\sqrt{-\ln(t')})$. Thus, as observed in a number of recent experiments, the scaling can easily be interpreted as evidence of a single non-trivial scaling exponent. Our predictions are confirmed by numerical simulations

Additive Equivalence in Turbulent Drag Reduction by Flexible and Rodlike Polymers

We address the "Additive Equivalence" discovered by Virk and coworkers: drag reduction affected by flexible and rigid rodlike polymers added to turbulent wall-bounded flows is limited from above by a very similar Maximum Drag Reduction (MDR) asymptote. Considering the equations of motion of rodlike polymers in wall-bounded turbulent ensembles, we show that although the microscopic mechanism of attaining the MDR is very different, the macroscopic theory is isomorphic, rationalizing the interesting experimental observations.Comment: 8 pages, PRE, submitte

Experimental and numerical investigations of flow structure and momentum transport in a turbulent buoyancy-driven flow inside a tilted tube.

Buoyancy-driven turbulent mixing of fluids of slightly different densities [At = Δρ/(2〈ρ〉) = 1.15×10−2] in a long circular tube tilted at an angle θ = 15° from the vertical is studied at the local scale, both experimentally from particle image velocimetry and laser induced fluorescence measurements in the vertical diametrical plane and numerically throughout the tube using direct numerical simulation. In a given cross section of the tube, the axial mean velocity and the mean concentration both vary linearly with the crosswise distance z from the tube axis in the central 70% of the diameter. A small crosswise velocity component is detected in the measurement plane and is found to result from a four-cell mean secondary flow associated with a nonzero streamwise component of the vorticity. In the central region of the tube cross section, the intensities of the three turbulent velocity fluctuations are found to be strongly different, that of the streamwise fluctuation being more than twice larger than that of the spanwise fluctuation which itself is about 50% larger than that of the crosswise fluctuation. This marked anisotropy indicates that the turbulent structure is close to that observed in homogeneous turbulent shear flows. Still in the central region, the turbulent shear stress dominates over the viscous stress and reaches a maximum on the tube axis. Its crosswise variation is approximately accounted for by a mixing length whose value is about one-tenth of the tube diameter. The momentum exchange in the core of the cross section takes place between its lower and higher density parts and there is no net momentum exchange between the core and the near-wall regions. A sizable part of this transfer is due both to the mean secondary flow and to the spanwise turbulent shear stress. Near-wall regions located beyond the location of the extrema of the axial velocity (|z|≳0.36 d) are dominated by viscous stresses which transfer momentum toward (from) the wall near the top (bottom) of the tube

Void elimination in screen printed thick film dielectric pastes

The problem is to understand the mechanisms for the formation and evolution of defects in wet screen printed layers. The primary objective is to know how best to alter the properties of the paste (rather than the geometry of the screen printing process itself) in order to eliminate the defects. With these goals in mind the work done during the Study Group reported here was as follows; to describe a simple model for the closure of craters, a model for the partial closure of vias, a possible mechanism for the formation of pinholes and finally a more detailed consideration of the screen printing process

Stress balance in nano-patterned N/Cu(001) surfaces

We employ helium atom scattering (HAS) and density functional theory (DFT) based on the ultrasoft pseudopotential scheme and the plane-wave basis set to investigate the strain and stress balance in nano-patterned N/Cu(001) surfaces. HAS shows that, with increasing N coverage (and decreasing stripe widths), the stress-relief-driven lateral expansion of the averaged lattice parameter within finite-sized N-containing patches reduces from 3.5% to 1.8% and that, beyond a critical exposure, the lateral expansion of the patches increases again slightly, to 2.4%. The latter implies that in this higher coverage range the compressive stress is partially relieved via another mechanism, which turns out to be nucleation of Cu-vacancy trenches. In full agreement with the above and previous experimental observations, DFT calculations show that an optimized N-induced c(2\times2) structure has a net surface stress level of 4.2 N/m and such stress is effectively relieved when stripes of clean Cu(001) form along the direction or when trench-like steps of Cu atoms form along the direction. Additionally, the calculations demonstrate that (contrary to earlier suggestions) rumpling displacements within the outermost Cu layer do not act to relieve the compressive surface stress levels and that, while clock-like displacements could relieve stress levels, such displacements are energetically unstable

Micro-Capsules in Shear Flow

This paper deals with flow-induced shape transitions of elastic capsules. The state of the art concerning both theory and experiments is briefly reviewed starting with dynamically induced small deformation of initially spherical capsules and the formation of wrinkles on polymerized membranes. Initially non-spherical capsules show tumbling and tank-treading motion in shear flow. Theoretical descriptions of the transition between these two types of motion assuming a fixed shape are at variance with the full capsule dynamics obtained numerically. To resolve the discrepancy, we expand the exact equations of motion for small deformations and find that shape changes play a dominant role. We classify the dynamical phase transitions and obtain numerical and analytical results for the phase boundaries as a function of viscosity contrast, shear and elongational flow rate. We conclude with perspectives on timedependent flow, on shear-induced unbinding from surfaces, on the role of thermal fluctuations, and on applying the concepts of stochastic thermodynamics to these systems.Comment: 34 pages, 15 figure

A new model for simulating colloidal dynamics

We present a new hybrid lattice-Boltzmann and Langevin molecular dynamics scheme for simulating the dynamics of suspensions of spherical colloidal particles. The solvent is modeled on the level of the lattice-Boltzmann method while the molecular dynamics is done for the solute. The coupling between the two is implemented through a frictional force acting both on the solvent and on the solute, which depends on the relative velocity. A spherical colloidal particle is represented by interaction sites at its surface. We demonstrate that this scheme quantitatively reproduces the translational and rotational diffusion of a neutral spherical particle in a liquid and show preliminary results for a charged spherical particle. We argue that this method is especially advantageous in the case of charged colloids.Comment: For a movie click on the link below Fig

Brewing of filter coffee

We report progress on mathematical modelling of coffee grounds in a drip filter coffee machine. The report focuses on the evolution of the shape of the bed of coffee grounds during extraction with some work also carried out on the chemistry of extraction. This work was sponsored by Philips who are interested in understanding an observed correlation between the final shape of the coffee grounds and the quality of the coffee. We used experimental data gathered by Philips and ourselves to identify regimes in the coffee brewing process and relevant regions of parameter space. Our work makes it clear that a number of separate processes define the shape of the coffee bed depending on the values of the parameters involved e.g. the size of the grains and the speed of fluid flow during extraction. We began work on constructing mathematical models of the redistribution of the coffee grounds specialised to each region and on a model of extraction. A variety of analytic and numerical tools were used. Furthermore our research has progressed far enough to allow us to begin to exploit connections between this problem and other areas of science, in particular the areas of sedimentology and geomorphology, where the processes we have observed in coffee brewing have been studied