Shear-stress controlled dynamics of nematic complex fluids

Based on a mesoscopic theory we investigate the non-equilibrium dynamics of a sheared nematic liquid, with the control parameter being the shear stress $\sigma_{\mathrm{xy}}$ (rather than the usual shear rate, $\dot\gamma$). To this end we supplement the equations of motion for the orientational order parameters by an equation for $\dot\gamma$, which then becomes time-dependent. Shearing the system from an isotropic state, the stress- controlled flow properties turn out to be essentially identical to those at fixed $\dot\gamma$. Pronounced differences when the equilibrium state is nematic. Here, shearing at controlled $\dot\gamma$ yields several non-equilibrium transitions between different dynamic states, including chaotic regimes. The corresponding stress-controlled system has only one transition from a regular periodic into a stationary (shear-aligned) state. The position of this transition in the $\sigma_{\mathrm{xy}}$-$\dot\gamma$ plane turns out to be tunable by the delay time entering our control scheme for $\sigma_{\mathrm{xy}}$. Moreover, a sudden change of the control method can {\it stabilize} the chaotic states appearing at fixed $\dot\gamma$.Comment: 10 pages, 11 figure

Calculation of compressible flow in and about three-dimensional inlets with and without auxiliary inlets by a higher-order panel method

A three dimensional higher order panel method was specialized to the case of inlets with auxiliary inlets. The resulting program has a number of graphical input-output features to make it highly useful to the designer. The various aspects of the program are described instructions for its use are presented

Two-state shear diagrams for complex fluids in shear flow

The possible "phase diagrams'' for shear-induced phase transitions between two phases are collected. We consider shear-thickening and shear-thinning fluids, under conditions of both common strain rate and common stress in the two phases, and present the four fundamental shear stress vs. strain rate curves and discuss their concentration dependence. We outline how to construct more complicated phase diagrams, discuss in which class various experimental systems fall, and sketch how to reconstruct the phase diagrams from rheological measurements

Current activities at IITRI on high- temperature protective coatings

Heat resistant protective coatings for use in liquid propellant rocket engine

An Isotopic analysis of the hydrology and riparian vegetation water sources on Bishop Creek

Five power generation plants along an eleven kilometer stretch divert Bishop Creek water for hydro-electric power. Stream diversion may be adversely affecting the riparian vegetation. Stable isotopic analysis is employed to determine surface water/ground-water interactions along the creek. surface water originates primarily from three headwater lakes. Discharge into Bishop Creek below the headwaters is primarily derived from ground water. The average δD and δ18O values are significantly different for surface water and ground water that an isotopic analysis can delineate between these two components of flow. Therefore isotopic shifts along the creek can determine gaining reaches. In addition, by knowing the isotopic signatures of various waters in the watershed, it may be possible to examine tree waters to determine their water source(s)

Calculation of compressible flow about three-dimensional inlets with auxiliary inlets, slats and vanes by means of a panel method

An efficient and user oriented method was constructed for calculating flow in and about complex inlet configurations. Efficiency is attained by: (1) the use of a panel method; (2) a technique of superposition for obtaining solutions at any inlet operating condition; and (3) employment of an advanced matrix iteration technique for solving large full systems of equations, including the nonlinear equations for the Kutta condition. User concerns are addressed by the provision of several novel graphical output options that yield a more complete comprehension of the flowfield than was possible previously

Excimer lasers

The results of a two-year investigation into the possibility of developing continuous wave excimer lasers are reported. The program included the evaluation and selection of candidate molecular systems and discharge pumping techniques. The K Ar/K2 excimer dimer molecules and the xenon fluoride excimer molecule were selected for study; each used a transverse and capillary discharges pumping technique. Experimental and theoretical studies of each of the two discharge techniques applied to each of the two molecular systems are reported. Discharge stability and fluorine consumption were found to be the principle impediments to extending the XeF excimer laser into the continuous wave regime. Potassium vapor handling problems were the principal difficulty in achieving laser action on the K Ar/K2 system. Of the four molecular systems and pumping techniques explored, the capillary discharge pumped K Ar/K2 system appears to be the most likely candidate for demonstrating continuous wave excimer laser action primarily because of its predicted lower pumping threshold and a demonstrated discharge stability advantage