Modelling of dimensional stability of fiber reinforced composite materials

Various methods of predicting the expansion and diffusion properties of composite laminates are reviewed. The prediction equations for continuous fiber composites can be applied to SMC composites as the effective fiber aspect ratio in the latter is large enough. The effect of hygrothermal expansion on the dimensional stability of composite laminates was demonstrated through the warping of unsymmetric graphite/epoxy laminates. The warping is very sensitive to the size of the panel, and to the moisture content which is in turn sensitive to the relative humidity in the environment. Thus, any long term creep test must be carried out in a humidity-controlled environment. Environmental effects in SMC composites and bulk polyester were studied under seven different environments. The SMC composites chosen are SMC-R25, SMC-R40, and SMC-R65

Complete electroweak one-loop radiative corrections to top-pair production at TESLA -- a comparison

Electroweak one-loop radiative corrections to the process e^+ e^- -> t tbar are revisited. Two groups from Karlsruhe and Bielefeld/Zeuthen performed independent calculations of both (virtual and soft) QED contributions and weak virtual corrections. For the angular distribution an agreement of at least eight digits for the weak corrections and of at least seven digits for additional photonic corrections is established.Comment: 12 pages, minor improvement of soft photon correction

CP violating asymmetry in H±→W±h1H^\pm\to W^\pm h_1 decays

The CP violating asymmetry from the decay rates $H^\pm\to W^\pm h_1$ of charged Higgs bosons into the lightest neutral Higgs boson and a $W^\pm$ boson is calculated and discussed in the complex MSSM. The contributions from all complex phases are considered, especially from the top-squark trilinear coupling, which induces a large contribution to the CP asymmetry.Comment: 19 pages, 10 figures, version published in JHE

QCD Corrections to t anti-b H^- Associated Production in e^+ e^- Annihilation

We calculate the QCD corrections to the cross section of e^+ e^- -> t anti-b H^- and its charge-conjugate counterpart within the minimal supersymmetric extension of the Standard Model. This process is particularly important if m_t b H^+ and e^+ e^- -> H^+ H^- are not allowed kinematically. Large logarithmic corrections that arise in the on-mass-shell scheme of quark mass renormalization, especially from the t anti-b H^- Yukawa coupling for large values of tan(beta), are resummed by adopting the modified minimal-subtraction scheme, so that the convergence behavior of the perturbative expansion is improved. The inclusion of the QCD corrections leads to a significant reduction of the theoretical uncertainties due to scheme and scale dependences.Comment: 21 pages (Latex), 8 figures (Postscript); detailed discussion of scheme and scale dependences adde

Automated calculations for massive fermion production with aITALC

The package aITALC has been developed for the automated calculation of radiative corrections to two-fermion production at $e^+ e^-$ colliders. The package uses Diana, Qgraf, Form, Fortran, FF, LoopTools, and further unix/linux tools. Numerical results are presented for $e^+e^- \to e^+e^-, mu^+mu^-, b \bar{s}, t \bar{c}$.Comment: Contribution to the proceedings of "Loops and Legs in Quantum Field Theory 2004", Zinnowitz, Usedom Island, Germany, April 2004. 5 pages, latex, espcrc2, 5 figures, 1 tabl

Two-loop SUSY QCD corrections to the chargino masses in the MSSM

We have calculated the two-loop strong interaction corrections to the chargino pole masses in the DRbar'-scheme in the Minimal Supersymmetric Standard Model (MSSM) with complex parameters. We have performed a detailed numerical analysis for a particular point in the parameter space and found corrections of a few tenths of a percent. We provide a computer program which calculates chargino and neutralino masses with complex parameters including the one-loop corrections and all two-loop SQCD effects.Comment: 12 pages, 11 figures, references modified, clarifications adde

Methylation Status of Imprinted Genes and Repetitive Elements in Sperm DNA from Infertile Males

Stochastic, environmentally and/or genetically induced disturbances in the genome-wide epigenetic reprogramming processes during male germ-cell development may contribute to male infertility. To test this hypothesis, we have studied the methylation levels of 2 paternally (H19 and GTL2) and 5 maternally methylated (LIT1, MEST, NESPAS, PEG3, and SNRPN) imprinted genes, as well as of ALU and LINE1 repetitive elements in 141 sperm samples, which were used for assisted reproductive technologies (ART), including 106 couples with strictly male-factor or combined male and female infertility and 28 couples with strictly female-factor infertility. Aberrant methylation imprints showed a significant association with abnormal semen parameters, but did not seem to influence ART outcome. Repeat methylation also differed significantly between sperm samples from infertile and presumably fertile males. However, in contrast to imprinted genes, ALU methylation had a significant impact on pregnancy and live-birth rate in couples with male-factor or combined infertility. ALU methylation was significantly high-er in sperm samples leading to pregnancy and live-birth than in those that did not. Sperm samples leading to abortions showed significantly lower ALU methylation levels than those leading to the birth of a baby. Copyright (C) 2011 S. Karger AG, Base

Nucleation and growth of rolling contact failure of 440C bearing steel

A 'two-body' elasto-plastic finite element model of 2-dimensional rolling and rolling-plus-sliding was developed to treat the effect of surface irregularities. The model consists of a smooth cylinder in contact with a semi-infinite half-space that is either smooth or fitted with one of 0.4 microns deep or 7 microns deep groove, or a 0.4 microns high ridge-like asperity. The model incorporates elastic-linear-kinematic hardening-plastic (ELKP) and non-linear-kinematic hardening-plastic (NLKP) material constitutive relations appropriate for hardened bearing steel and the 440C grade. The calculated contact pressure distribution is Hertzian for smooth body contact, and it displays intense, stationary, pressure spikes superposed on the Hertzian pressure for contact with the grooved and ridged surface. The results obtained for the 0.4 microns deep groove compare well with those reported by Elsharkawy and Hamrock for an EHD lubricated contact. The effect of translating the counterface on the half space as opposed to indenting the half space with the counter face with no translation is studied. The stress and strain values near the surface are found to be similar for the two cases, whereas they are significantly different in the subsurface. It is seen that when tiny shoulders are introduced at the edge of the groove in the finite element model, the incremental plasticity and residual stresses are significantly higher in the vicinity of the right shoulder (rolling direction is from left to right) than at the left shoulder. This may explain the experimental observation that the spall nucleation occurs at the exit end of the artificially planted indents. Pure rolling calculations are compared with rolling + sliding calculations. For a coefficient of friction, mu = 0.1, the effect of friction is found to be small. Efforts were made to identify the material constitutive relations which best describe the deformation characteristics of the bearing steels in the initial few cycles. Elastic-linear-kinematic hardening-plastic (ELKP) material constitutive relations produce less net plastic deformation in the initial stages for a given stress, than seen in experiments. A new set of constitutive relations: non-linear-kinematic hardening-plastic (NLKP) was used. This material model produces more plasticity than the ELKP model and shows promise for treating the net distortions in the early stages. Techniques for performing experimental measurements that can be compared with the finite element calculations were devised. The measurements are being performed on 9mm-diameter, 440C steel cylindrical rolling elements in contact with 12.5 mm-diameter, 52100 steel balls in a 3-ball-rod fatigue test machine operating at 3600 RPM. Artificial, 7 microns deep, indents were inserted on the running track of the cylindrical rolling elements and profilometer measurements of these indents made, before and after the rolling. These preliminary measurements show that the indents are substantially deformed plastically in the process of rolling. The deformations of the groove calculated with the finite element model are comparable to those measured experimentally

Automated use of DIANA for two-fermion production at colliders

We describe packages for the calculation of radiative corrections to two-fermion production at colliders. The packages use DIANA, and also QGRAF, FORM, Fortran, and further unix/linux tools. The one-loop calculations in the Standard Model are highly automatized with the package aITALC. Further, the automatic determination of all the matrix elements for two-loop corrections to massive Bhabha scattering in QED and the classification of their topologies and prototypes is done with DIANA. A generalization to the Standard Model is straightforward.Comment: To appear in the proceedings of ACAT03, Dec 2003, KEK, Japa

Multi-excitonic complexes in single InGaN quantum dots

Cathodoluminescence spectra employing a shadow mask technique of InGaN layers grown by metal organic chemical vapor deposition on Si(111) substrates are reported. Sharp lines originating from InGaN quantum dots are observed. Temperature dependent measurements reveal thermally induced carrier redistribution between the quantum dots. Spectral diffusion is observed and was used as a tool to correlate up to three lines that originate from the same quantum dot. Variation of excitation density leads to identification of exciton and biexciton. Binding and anti-binding complexes are discovered.Comment: 3 pages, 4 figure