18 research outputs found
Flexural strength of acrylic resin repairs processed by different methods: water bath, microwave energy and chemical polymerization
A new approach to cure and reinforce cold-cured acrylics
Purpose: The low degree of polymerization of cold-cured acrylics has resulted in inferior mechanical properties and fracture vulnerability in orthodontics removable appliances. Methods: In this study, the effect of reinforcement by various concentrations of chopped E-glass fibers (0%, 1%, 2%, 3% and 5% by weight of resin powder) and post-curing microwave irradiation (800 W for 3 min) on the flexural strength of cold-cured acrylics was evaluated at various storage conditions (at room temperature for 1 day and 7 days; at water storage for 7, 14 and 30 days). Results: The data was analyzed by using 1-way and 2-way ANOVA, and a Tukey post hoc test (α = .05). The specimens with chopped E-glass fibers treated with post-curing microwave irradiation significantly increased the flexural strength of cold-cured PMMA. The optimal concentration might be 2% fibers under irradiation. Conclusions: The exhibited reinforcement effect lasted in a consistent trend for 14 days in water storage. A new fiber-acrylic mixing method was also developed. © 2012 The Author(s).published_or_final_versio
Continuous and Short Fiber Reinforced Composite in Root Post-Core System of Severely Damaged Incisors
Effect of cavity preparation on the flexural strengths of acrylic resin repairs
OBJECTIVE: To investigate the effect of cavity preparation on the flexural strength of heat-curing denture resin when repaired with an auto-curing resin. MATERIAL AND METHODS: Ninety-six rectangular specimens (64x10x2.5 mm) prepared from heat-curing denture base resin (Meliodent) were randomly divided into four groups before repair. One group was left intact as control. Each repair specimen was sectioned into two; one group was repaired using the conventional repair method (Group 1). Two groups had an additional transverse cavity (2x3.5x21.5 mm) prepared prior to the repair; one repaired with (Group 2) and one without glass-fiber reinforcement (Group 3). A three-point flexural bending test according to the ISO 1567:1999 specification8 for denture base polymers was carried out on all groups after 1, 7 and 30 days of water immersion. Statistical analysis was carried out using two-way ANOVA, Kruskal Wallis and post-hoc Mann Whitney tests. RESULTS: The highest flexural strength was observed in the control group. Control and conventional repairs group (Group 1) showed reduction in the flexural strength 30 days after water immersion. No significant change in the strength was observed for Groups 2 and 3 where the repair joints were similarly prepared with additional transverse cavity. CONCLUSION: Repaired specimens showed lower flexural strength values than intact heat-curing resin. Cavity preparation had no significant effect on the flexural strength of repair with water immersion
The Effect of Incorporation, Orientation and Silane Treatment of Glass Fibers on the Fracture Resistance of Interim Fixed Partial Dentures
Fracture of interim fixed partial dentures (FPD) is of important concern to the dental surgeon, especially with long-span fixed partial dentures or areas of heavy occlusal stress. Polymers used in interim FPDs, reinforced with glass fibers have shown to have a positive effect on the fracture resistance of interim FPDs. Since little research has been done on the influence of silane treated glass fibers on the fracture resistance of interim FPDs, this study was conducted to evaluate the effect of silane treatment of glass fibers on the fracture resistance of interim FPDs and its correlation with the position of fiber reinforcement and length of the span of the interim FPD. Interim FPDs were fabricated from an autopolymerizing polymethyl methacrylate (PMMA) resin. Seven FPDs were made in each group. The FPDs in the control group were unreinforced, and in the other groups the FPDs were reinforced either with non silane treated glass fiber or with silane treated glass fiber. The fibers were placed in two different locations in the FPDs. Three length of span of FPDs were tested. The load was applied to the FPD by a steel ball placed in the center of the pontic space. One Way Anova, Two Way Anova, Studentized range test (Scheffe’s). Results showed that the load required for fracturing the unreinforced FPDs varied from 272 to 998 N. Mean fracture load of reinforced FPDs varied from 536 to 1642 N. One-way analysis of variance showed that the position of fibers and the silane treatment fibers significantly affected the fracture load. The results of this study suggested that the silane treatment of glass fibers had a marked improvement in the fracture resistance of FPDs as compared to untreated glass fibers. Selective placement of the glass fibers at the undersurface of the pontic and the occlusal surface of the interim fixed partial denture showed more increase in the fracture resistance as compared to the randomly distributed glass fibers. The glass fiber reinforcement is effective in increasing the fracture resistance with the effectiveness most evident in interim FPDs with long spans. With increase in the length of span of interim fixed partial denture the fracture resistance was shown to decrease significantly in all the groups