22,532 research outputs found
Cold-air performance of a 12.766-centimeter-tip-diameter axial-flow cooled turbine. 1: Design and performance of a solid blade configuration
A solid blade version of a single-stage, axial-flow turbine was investigated to determine its performance over a range of speeds from 0 to 105 percent of equivalent design speed and over a range of total to static pressure ratios from 1.62 to 5.07. The results of this investigation will be used as a baseline for comparison with those obtained from a cooled version of this turbine
Effect of coolant flow ejection on aerodynamic performance of low-aspect-ratio vanes. 1: Performance with coolant ejection holes plugged
The aerodynamic performance of a low aspect ratio turbine vane designed with coolant flow ejection holes on the vane surfaces was experimentally determined in a full-annular cascade with the coolant ejection holes plugged. The purpose was to establish a baseline for comparison with tests where flow is ejected from the vane surfaces. The vanes were tested over a mean-section ideal critical velocity ratio range of 0.64 to 0.98. This ideal critical velocity ratio corresponds to the vane inlet total to vane aftermixed static pressure ratio at the mean section. The variations in vane efficiency and aftermixed flow conditions with circumferential and radial position were obtained
Cold air performance of a 12.766-centimeter-tip-diameter axial-flow cooled turbine. 2: Effect of air ejection on turbine performance
An air cooled version of a single-stage, axial-flow turbine was investigated to determine aerodynamic performance with and without air ejection from the stator and rotor blades surfaces to simulate the effect of cooling air discharge. Air ejection rate was varied from 0 to 10 percent of turbine mass flow for both the stator and the rotor. A primary-to-air ejection temperature ratio of about 1 was maintained
Effect of rotor tip clearance and configuration on overall performance of a 12.77-centimeter tip diameter axial-flow turbine
The rotor tip clearance was obtained by use of a recess in the casing above the rotor blades and also by use of a reduced blade height. For the recessed casing configuration, the optimum rotor blade height was found to be the one where the rotor tip diameter was equal to the stator tip diameter. The tip clearance loss associated with this optimum recessed casing configuration was less than that for the reduced blade height configuration
Cold-air performance of a tip turbine designed to drive a lift fan
Performance was obtained over a range of speeds and pressure ratios for a 0.4 linear scale version of the LF460 lift fan turbine with the rotor radial tip clearance reduced to about 2.5 percent of the rotor blade height. These tests covered a range of speeds from 60 to 140 percent of design equivalent speed and a range of scroll inlet total to diffuser exit static pressure ratios from 2.6 to 4.2. Results are presented in terms of equivalent mass flow, equivalent torque, equivalent specific work, and efficiency
Turbine for ordnance turbojet engine. 2: Cold-air performance with opened stator
A single-stage axial-flow turbine was investigated to determine the effect of increased stator throat area on the performance level of a turbojet engine turbine. The stator blades were bent to increase the throat area in order to move the compressor operating point in the engine farther away from surge. Results are compared with those obtained with the as-cast stator setting
Management of germ cell tumors in children: Approaches to cure
The introduction of cisplatinum chemotherapy and current advances in the surgical treatment have resulted in a dramatic improvement of the prognosis of children with malignant germ cell tumors (GCT). Cisplatinum chemotherapy generally results in sufficient systemic tumor control, but local relapses may still occur in patients who did not receive adequate local treatment. Therefore, the therapeutic consideration must take into account age, primary site of the tumor, and its histology. In gonadal tumors, there is a high chance of primary complete resection since these tumors tend to be encapsulated, and particularly testicular GCT are often detected at a low tumor stage. In contrast, a primary complete resection may be impossible in large nongonadal tumors such as sacrococcygeal or mediastinal GCT. In these tumors, a neoadjuvant or pre-operative chemotherapy after clinical diagnosis by imaging and evaluation of tumor markers significantly facilitates complete resection on delayed surgery. In addition, the impact of chemotherapy on local tumor control may be enhanced by locoregional hyperthermia. In most intracranial GCT complete resection is impossible and may be associated with significant morbidity. Nevertheless, biopsy is essential for diagnosis in nonsecreting tumors. In intracranial GCT, radiotherapy significantly contributes to local tumor control, and doses are stratified according to histology. These general considerations have been integrated into national and international cooperative treatment protocols. In most current protocols, treatment is stratified according to an initial risk assessment that includes the parameters age, site, histology, stage, completeness of resection and the tumor markers alpha(1)-fetoprotein (AFP) and human choriogonadotropin (beta-HCG). With such modern protocols overall cure rates above 80% can be achieved. Moreover, the previously high-risk groups may now expect a favorable prognosis with this risk-adapted treatment, whereas an increasing number of low-risk patients are treated expectantly or with significantly reduced chemotherapy. As current biologic studies reveal distinct genetic patterns in childhood GCT, it can be expected that further combined clinical and genetic studies will be valuable for risk assessment of childhood GCT
Cold-air performance of a tip turbine designed to drive a lift fan. 3: Effect of simulated fan leakage on turbine performance
Performance data were obtained experimentally for a 0.4 linear scale version of the LF460 lift fan turbine for a range of scroll inlet total to diffuser exit static pressure ratios at design equivalent speed with simulated fan leakage air. Tests were conducted for full and partial admission operation with three separate combinations of rotor inlet and rotor exit leakage air. Data were compared to the results obtained from previous investigations in which no leakage air was present. Results are presented in terms of mass flow, torque, and efficiency
Recommended from our members
A combined statistical and dynamical approach for downscaling large-scale footprints of European windstorms
The occurrence of mid-latitude windstorms is related to strong socio-economic effects. For detailed and reliable regional impact studies, large datasets of high-resolution wind fields are required. In this study, a statistical downscaling approach in combination with dynamical downscaling is introduced to derive storm related gust speeds on a high-resolution grid over Europe. Multiple linear regression models are trained using reanalysis data and wind gusts from regional climate model simulations for a sample of 100 top ranking windstorm events. The method is computationally inexpensive and reproduces individual windstorm footprints adequately. Compared to observations, the results for Germany are at least as good as pure dynamical downscaling. This new tool can be easily applied to large ensembles of general circulation model simulations and thus contribute to a better understanding of the regional impact of windstorms based on decadal and climate change projections
Cold air performance of a tip turbine designed to drive a lift fan. 2: Partial admission
Partial admission performance was obtained for a 0.4 linear scale version of the LF460 lift fan turbine over a range of speed from 40 to 140 percent of design equivalent speed and a range of scroll inlet total to diffuser exit static pressure ratio from 2.2 to 5.0. The investigation was conducted in two parts, with each part using a different side of the turbine scroll to simulate loss of a gas generator. Each side had an arc of admission of 180. Results are presented in terms of specific work, torque, mass flow, and efficiency
- …