57 research outputs found
Optimum structural design with static aeroelastic constraints
The static aeroelastic performance characteristics, divergence velocity, control effectiveness and lift effectiveness are considered in obtaining an optimum weight structure. A typical swept wing structure is used with upper and lower skins, spar and rib thicknesses, and spar cap and vertical post cross-sectional areas as the design parameters. Incompressible aerodynamic strip theory is used to derive the constraint formulations, and aerodynamic load matrices. A Sequential Unconstrained Minimization Technique (SUMT) algorithm is used to optimize the wing structure to meet the desired performance constraints
Fatigue Life Predictions of Additively Manufactured Components for Satelite Structures
The fatigue life properties of Additive Manufactured (AM) components are limited due to the defects naturally generated from the AM Process. For limited design life problems the finite fatigue life El-Haddad model linked defect size, applied stress, and design life. This paper developed a method to predict the smallest defect of interest for a given load case and the lowest failure generating stress for a given defect size. Experimental testing validated the method steps. The model was adjusted to demonstrate the space utility based on a 12U CubeSat chassis. Applying the design life and expected load, the finite fatigue life El-Haddad model predicted the minimum defect size for two configurations of the 12U CubeSat. The minimum defect size defined the Non-Destructive Evaluation (NDE) criteria for component certification. Combining the worst case potential defect size with the design life, the finite fatigue life El-Haddad model defined a minimum stress to generate failure. Linking the minimum stress value to the CubeSat Finite Element Model (FEM) predicted every location on the structure that could potentially fail due to the formation of AM defects. This second aspect defined the required inspection region to certify the structure for the given load case and design life
Concurrent Engineering Tools for Forging Die and Process Design
This paper discusses the development of engineering tools for die shape design in the forging process and the utilization of this information for determining optimal operating conditions. The tools discussed here are based on computer graphics, finite element modeling, design optimization and optimal control strategies, and can be run on personal computers, work stations and main frame computers, to meet a variety of customer needs and to provide user friendly tools for conducting “what if” studies. The methods developed here are applicable to several unit processes like extrusion, shape rolling, etc., besides forging. Details about the design variables, design constraints, objectives, analytical sensitivity calculations, condensed states, satisfaction of behavior constraints, and the optimal tracking algorithm are presented here with engineering case studies
Concurrent Engineering Tools for Forging Die and Process Design
This paper discusses the development of engineering tools for die shape design in the forging process and the utilization of this information for determining optimal operating conditions. The tools discussed here are based on computer graphics, finite element modeling, design optimization and optimal control strategies, and can be run on personal computers, work stations and main frame computers, to meet a variety of customer needs and to provide user friendly tools for conducting “what if” studies. The methods developed here are applicable to several unit processes like extrusion, shape rolling, etc., besides forging. Details about the design variables, design constraints, objectives, analytical sensitivity calculations, condensed states, satisfaction of behavior constraints, and the optimal tracking algorithm are presented here with engineering case studies
Structural Reliability Analysis and Optimization: Use of Approximations
This report is intended for the demonstration of function approximation concepts and their applicability in reliability analysis and design. Particularly, approximations in the calculation of the safety index, failure probability and structural optimization (modification of design variables) are developed. With this scope in mind, extensive details on probability theory are avoided. Definitions relevant to the stated objectives have been taken from standard text books. The idea of function approximations is to minimize the repetitive use of computationally intensive calculations by replacing them with simpler closed-form equations, which could be nonlinear. Typically, the approximations provide good accuracy around the points where they are constructed, and they need to be periodically updated to extend their utility. There are approximations in calculating the failure probability of a limit state function. The first one, which is most commonly discussed, is how the limit state is approximated at the design point. Most of the time this could be a first-order Taylor series expansion, also known as the First Order Reliability Method (FORM), or a second-order Taylor series expansion (paraboloid), also known as the Second Order Reliability Method (SORM). From the computational procedure point of view, this step comes after the design point identification; however, the order of approximation for the probability of failure calculation is discussed first, and it is denoted by either FORM or SORM. The other approximation of interest is how the design point, or the most probable failure point (MPP), is identified. For iteratively finding this point, again the limit state is approximated. The accuracy and efficiency of the approximations make the search process quite practical for analysis intensive approaches such as the finite element methods; therefore, the crux of this research is to develop excellent approximations for MPP identification and also different approximations including the higher-order reliability methods (HORM) for representing the failure surface. This report is divided into several parts to emphasize different segments of the structural reliability analysis and design. Broadly, it consists of mathematical foundations, methods and applications. Chapter I discusses the fundamental definitions of the probability theory, which are mostly available in standard text books. Probability density function descriptions relevant to this work are addressed. In Chapter 2, the concept and utility of function approximation are discussed for a general application in engineering analysis. Various forms of function representations and the latest developments in nonlinear adaptive approximations are presented with comparison studies. Research work accomplished in reliability analysis is presented in Chapter 3. First, the definition of safety index and most probable point of failure are introduced. Efficient ways of computing the safety index with a fewer number of iterations is emphasized. In chapter 4, the probability of failure prediction is presented using first-order, second-order and higher-order methods. System reliability methods are discussed in chapter 5. Chapter 6 presents optimization techniques for the modification and redistribution of structural sizes for improving the structural reliability. The report also contains several appendices on probability parameters
Reduced-Order Model Development for Airfoil Forced Response
Two new reduced-order models are developed to accurately and rapidly predict geometry
deviation effects on airfoil forced response. Both models have significant application to improved
mistuning analysis. The first developed model integrates a principal component analysis
approach to reduce the number of defining geometric parameters, semianalytic eigensensitivity
analysis, and first-order Taylor series approximation to allow rapid as-measured airfoil
response analysis. A second developed model extends this approach and quantifies both random
and bias errors between the reduced and full models. Adjusting for the bias significantly
improves reduced-order model accuracy. The error model is developed from a regression analysis
of the relationship between airfoil geometry parameters and reduced-order model error,
leading to physics-based error quantification. Both models are demonstrated on an advanced
fan airfoil's frequency, modal force, and forced response
Recommended from our members
Optimum Design of Radial Drilling Machine Structure to Satisfy Static Rigidity and Natural Frequency Requirements
A computational capability is developed for the optimum design of radial drilling machine structure to satisfy static rigidity and natural frequency requirements using finite element idealization. The radial drilling machine structure is idealized with frame elements and is analyzed by using different combinations of cross sectional shapes for the radial arm and the column. From the results obtained, the best combination of cross sectional shapes is suggested for the structure. With this combination of cross sectional shapes, mathematical programming techniques are used to find the minimum weight design of the radial drilling machine structure. A sensitivity analysis is conducted about the optimum point to find the effects of changes in design variables on the structural weight and the response quantities
- …