Results from CHIPIX-FE0, a Small Scale Prototype of a New Generation Pixel Readout ASIC in 65nm CMOS for HL-LHC

CHIPIX65-FE0 is a readout ASIC in CMOS 65nm designed by the CHIPIX65 project for a pixel detector at the HL-LHC, consisting of a matrix of 64x64 pixels of dimension 50x50 μm2. It is fully functional, can work at low thresholds down to 250e− and satisfies all the specifications. Results confirm low-noise, fast performance of both the synchronous and asynchronous front-end in a complex digital chip. CHIPIX65-FE0 has been irradiated up to 600 Mrad and is only marginally affected on analog performance. Further irradiation to 1 Grad will be performed. Bump bonding to silicon sensors is now on going and detailed measurements will be presented. The HL-LHC accelerator will constitute a new frontier for particle physics after year 2024. One major experimental challenge resides in the inner tracking detectors, measuring particle position: here the dimension of the sensitive area (pixel) has to be scaled down with respect to LHC detectors. This paper describes the results obtained by CHIPIX65-FE0, a readout ASIC in CMOS 65nm designed by the CHIPIX65 project as small-scale demonstrator for a pixel detector at the HL-LHC. It consists of a matrix of 64x64 pixels of dimension 50x50 um2 pixels and contains several pieces that are included in RD53A, a large scale ASIC designed by the RD53 Collaboration: two out of three front-ends (a synchronous and an asynchronous architecture); several building blocks; a (4x4) pixel region digital architecture with central local buffer storage, complying with a 3 GHz/cm2 hit rate and a 1 MHz trigger rate maintaining a very high efficiency (above 99%). The chip is 100% functional, either running in triggered or trigger-less mode. All building-blocks (DAC, ADC, Band Gap, SER, sLVS-TX/RX) and very front ends are working as expected. Analog performance shows a remarkably low ENC of 90e-, a fast-rise time below 25ns and low-power consumption (about 4μA/pixel) in both synchronous and asynchronous front-ends; a very linear behavior of CSA and discriminator. No significant cross talk from digital electronics has been measured, achieving a low threshold of 250e-. Signal digitization is obtained with a 5b-Time over Threshold technique and is shown to be fairly linear, working well either at 80 MHz or with higher frequencies of 300 MHz obtained with a tunable local oscillator. Irradiation results up to 600 Mrad at low temperature (-20°C) show that the chip is still fully functional and analog performance is only marginally degraded. Further irradiation will be performed up to 1 Grad either at low or room temperature, to further understand the level of radiation hardness of CHIPIX65-FE0. We are now in the process of bump bonding CHIPIX65-FE0 to 3D and possibly planar silicon sensors during spring. Detailed results will be presented in the conference paper

First Measurements of a Prototype of a New Generation Pixel Readout ASIC in 65 nm CMOS for Extreme Rate HEP Detectors at HL-LHC

A first prototype of a readout ASIC in CMOS 65nm for a pixel detector at High Luminosity LHC is described. The pixel cell area is 50x50 um2 and the matrix consists of 64x64 pixels. The chip was designed to guarantee high efficiency at extreme data rates for very low signals and with low power consumption. Two different analogue front-end designs, one synchronous and one asynchronous, were implemented, both occupying an area of 35x35 um2. ENC value is below 100e- for an input capacitance of 50 fF and in-time threshold below 1000e-. Leakage current compensation up to 50 nA with power consumption below 5 uW. A ToT technique is used to perform charge digitization with 5-bit precision using either a 40 MHz clock or a local Fast Oscillator up to 800 MHz. Internal 10-bit DAC's are used for biasing, while monitoring is provided by a 12-bit ADC. A novel digital architecture has been developed to ensure above 99.5% hit efficiency at pixel hit rates up to 3 GHz/cm2, trigger rates up to 1 MHz and trigger latency of 12.5 us. The total power consumption per pixel is below 5uW. Analogue dead-time is below 1%. Data are sent via a serializer connected to a CMOS-to-SLVS transmitter working at 320 MHz. All IP-blocks and front-ends used are silicon-proven and tested after exposure to ionizing radiation levels of 500-800 Mrad. The chip was designed as part of the Italian INFN CHIPIX65 project and in close synergy with the international CERN RD53 and was submitted in July 2016 for production. Early test results for both front-ends regarding minimum threshold, auto-zeroing and low-noise performance are high encouraging and will be presented in this paper

Acute Delta Hepatitis in Italy spanning three decades (1991–2019): Evidence for the effectiveness of the hepatitis B vaccination campaign

Updated incidence data of acute Delta virus hepatitis (HDV) are lacking worldwide. Our aim was to evaluate incidence of and risk factors for acute HDV in Italy after the introduction of the compulsory vaccination against hepatitis B virus (HBV) in 1991. Data were obtained from the National Surveillance System of acute viral hepatitis (SEIEVA). Independent predictors of HDV were assessed by logistic-regression analysis. The incidence of acute HDV per 1-million population declined from 3.2 cases in 1987 to 0.04 in 2019, parallel to that of acute HBV per 100,000 from 10.0 to 0.39 cases during the same period. The median age of cases increased from 27 years in the decade 1991-1999 to 44 years in the decade 2010-2019 (p < .001). Over the same period, the male/female ratio decreased from 3.8 to 2.1, the proportion of coinfections increased from 55% to 75% (p = .003) and that of HBsAg positive acute hepatitis tested for by IgM anti-HDV linearly decreased from 50.1% to 34.1% (p < .001). People born abroad accounted for 24.6% of cases in 2004-2010 and 32.1% in 2011-2019. In the period 2010-2019, risky sexual behaviour (O.R. 4.2; 95%CI: 1.4-12.8) was the sole independent predictor of acute HDV; conversely intravenous drug use was no longer associated (O.R. 1.25; 95%CI: 0.15-10.22) with this. In conclusion, HBV vaccination was an effective measure to control acute HDV. Intravenous drug use is no longer an efficient mode of HDV spread. Testing for IgM-anti HDV is a grey area requiring alert. Acute HDV in foreigners should be monitored in the years to come

Editorial on the Special Issue “Advances in Pediatric Acute Kidney Injury”

Acute kidney injury (AKI) refers to a swift decline in kidney function, marked by the reduced excretion of waste products and disturbances in fluid and electrolyte balance [...

Tribological Characterization of Surface Treated Titanium for Orthopaedic Joints

Most not cemented total hip replacements combine a titanium alloy stem, a CoCrMo femoral head and an uUltra High Molecular Weight Polyethylene (UHMWPE) acetabular cup. In spite of the suboptimal biocompatibility, the higher cost and some dfficulties in machining, CoCrMo alloy is often preferred to titanium alloys thanks to its outstanding tribological properties, higher hardness and elastic modulus. Therefore, nowadays most of the heads of hip prostheses use CoCrMo as bearing material. Biocompatibility problems of CoCrMo are often associated with a nickel content of up to 1% in this alloy. In some clinical situations such a nickel percentage cannot be neglected. The rationale of the present study was to investigate the effect of various surface treatments and combinations of treatments, such as electrochemical oxidation (anodization), laser surface treatments and barrel polishing, on the tribological properties of commercially pure grade 2 titanium. The goal was to find a surface treatment capable to provide a wear resistant titanium surface, with tribological properties as good as those of CoCrMo. Wear tests were performed on a multidirectional pin-on-flat screening wear testing machine, using UHMWPE pins as second bearing material. The experiments showed the possibility to improve wear resistance of titanium to the CoCrMo levels.JRC.I.4-Nanotechnology and Molecular Imagin

Tribological Characterization of Surface Treatments to Enhance the Tribological Performances of Medical Grade Titanium

Titanium and its alloys are employed for many biomedical applications. One of the reasons of this success is related to the high biocompatibility of this material. As a matter of fact, its spontaneous capacity to create a passivation film of titanium oxide on the surface results in low amount of metal ions release in vivo and in a high resistance against corrosion. Moreover, the absence of Ni in its alloys represents an important issue in the evaluation of its biocompatibility, as compared to CoCrMo. As a matter of fact such an element is recognized as allergenic and cancerogenic agent. Nevertheless, the poor wear resistance of the Ti-oxide film keeps Ti from being employed in tribological applications. The present work investigates the possibility to apply surface treatments to the titanium in order to increase its wear resistance.JRC.I.4-Nanotechnology and Molecular Imagin

Tribological Characterization of Surface Treated Commercially Pure Titanium for Femoral Heads in Total Hip Replacement - A Feasibility Study

Most not cemented total hip replacements combine a titanium alloy stem, a CoCrMo femoral head and an ultra-high molecular weight polyethylene (UHMWPE) acetabular cup. In spite of its nickel content of up to 1% and the resulting biocompatibility issues in some clinical situations, the higher cost and some difficulties in machining, CoCrMo alloy is preferred to titanium alloys thanks to its outstanding tribological properties, higher hardness and elastic modulus. Nowadays most of the heads of hip prostheses use CoCrMo as bearing material. The present study investigates the effect of various surface treatments and combinations of treatments, such as electrochemical oxidation (anodization), laser surface melting and barrel polishing, on the tribological properties of commercially pure grade 2 titanium. The aim of the study was to characterize surface treatments capable of improving the tribological properties of titanium surface to the same extent of CoCrMo. The tribological properties were characterized by multidirectional pin-on-flat screening wear tests, using UHMWPE pins as bearing surface. The experiments showed the possibility to improve the wear resistance of titanium to the CoCrMo extent. Although further efforts will be required to optimize the experimented treatments, the results are encouraging to pursue this direction of investigation .JRC.I.4-Nanotechnology and Molecular Imagin