Highly porous scaffolds of PEDOT:PSS for bone tissue engineering.

UNLABELLED: Conjugated polymers have been increasingly considered for the design of conductive materials in the field of regenerative medicine. However, optimal scaffold properties addressing the complexity of the desired tissue still need to be developed. The focus of this study lies in the development and evaluation of a conductive scaffold for bone tissue engineering. In this study PEDOT:PSS scaffolds were designed and evaluated in vitro using MC3T3-E1 osteogenic precursor cells, and the cells were assessed for distinct differentiation stages and the expression of an osteogenic phenotype. Ice-templated PEDOT:PSS scaffolds presented high pore interconnectivity with a median pore diameter of 53.6±5.9µm and a total pore surface area of 7.72±1.7m2·g-1. The electrical conductivity, based on I-V curves, was measured to be 140µS·cm-1 with a reduced, but stable conductivity of 6.1µS·cm-1 after 28days in cell culture media. MC3T3-E1 gene expression levels of ALPL, COL1A1 and RUNX2 were significantly enhanced after 4weeks, in line with increased extracellular matrix mineralisation, and osteocalcin deposition. These results demonstrate that a porous material, based purely on PEDOT:PSS, is suitable as a scaffold for bone tissue engineering and thus represents a promising candidate for regenerative medicine. STATEMENT OF SIGNIFICANCE: Tissue engineering approaches have been increasingly considered for the repair of non-union fractions, craniofacial reconstruction or large bone defect replacements. The design of complex biomaterials and successful engineering of 3-dimensional tissue constructs is of paramount importance to meet this clinical need. Conductive scaffolds, based on conjugated polymers, present interesting candidates to address the piezoelectric properties of bone tissue and to induce enhanced osteogenesis upon implantation. However, conductive scaffolds have not been investigated in vitro in great measure. To this end, we have developed a highly porous, electrically conductive scaffold based on PEDOT:PSS, and provide evidence that this purely synthetic material is a promising candidate for bone tissue engineering

RAPID THERMAL-DIFFUSION OF SN FROM SPIN-ON-GLASS INTO GAAS

Diffusion of dopants into semiconductors from a spin-on-glass (SOG) source is of great interest because of its versatility, simplicity, and relatively low cost. SiO2 SOG films doped with Sn and/or Ga were used as a diffusion source on GaAs. Diffusion was studied during rapid thermal annealing with or without an As over-pressure ambient, which was produced by either the proximity over-pressure or the enhanced over-pressure proximity techniques. Diffusivity of Sn was observed to decrease as As over-pressure increases. Modifying the Sn doped SOG to contain 4 mole percent Ga slightly reduced the Sn diffusivity. An explanation of these results is proposed based on the chemical reactions between the SOG and GaAs. Highly doped layers (1-3 x 10(18) cm(-3)) with good electron mobility (>1000 cm(2)/V . s) resulting in abrupt shallow junctions (<0.5 mu m) were obtained.14282829283

Investigation on the competing effects of clay dispersion and matrix plasticisation for polypropylene/clay nanocomposites. Part I: morphology and mechanical properties

The key compatibiliser role of maleated polypropylene (MAPP) to improve the clay dispersability has been explicitly addressed in the fabrication process and material characterisation of polypropylene (PP)/clay nanocomposites. However, its matrix plasticiser role, which has been rarely mentioned, could adversely influence the excellent mechanical properties of such nanocomposites, resulting from the homogeneous clay dispersion. PP/clay nanocomposites in the presence of MAPP were prepared by twin screw extrusion and subsequently injection moulded with three typical material formulations in fixed parametric settings: (1) weight ratio (WR) of clay and MAPP, WR = 1:2; (2) MAPP content of 6 wt% and (3) clay content of 5 wt%. The morphological structures and mechanical properties of PP/clay nanocomposites were examined by using X-ray diffraction (XRD) analysis, transmission electron microscopy (TEM), scanning electron microscopy (SEM) and universal mechanical testing. The further improvement of mechanical properties was evidently hindered with very inconsiderable alteration of morphological structures in terms of the clay dispersion level. This observation could be ascribed to the change of MAPP role from a compatibiliser to a plasticiser because of its excessive amount used above a certain saturation level, which was found in the range of 3–6 wt% in MAPP contents for the enhancements of tensile and flexural properties of PP/clay nanocomposites

Investigation on the competing effects of clay dispersion and matrix plasticisation for polypropylene/clay nanocomposites. Part II: Crystalline structure and thermo-mechanical behaviour

In view of the structure–property relationship, the mechanical property enhancement of polypropylene (PP)/clay nanocomposites can also be associated with the alterations of their crystalline structures and behaviour in addition to the general interpretation of intercalation/exfoliation level and uniform dispersion of more rigid clay platelets with higher aspect ratios in the PP matrix. Wide-angle X-ray diffraction (WAXD) was utilised to evaluate the effects of clay content, maleated PP (MAPP) content (MAPP as the compatibiliser) on PP crystalline structures of nanocomposites. Furthermore, the melting and crystallisation behaviour of PP/clay nanocomposites was also investigated by conducting differential scanning calorimetry (DSC). The thermo-mechanical properties were characterised via dynamic mechanical thermal analysis (DMTA). It is observed that enhancement of mechanical properties are mainly affected by the preferred orientation of PP crystals, the growth of α-PP phase and effective nucleating agent role of additional clay while the excessive amount of MAPP becomes detrimental to these crucial aspects, which is also evidently revealed in DMTA measurements