Characterisation of thin chitosan films for guided tissue regeneration purposes

The morphology and structure of thin films containing chitosan (Ch) with montmorillonite (MMT) were characterised by scanning electron microscopy (SEM), atomic force microscopy (AFM) and attenuated total reflectance Fourier transform infrared spectroscopy (ATR-FTIR). Thin films of two chitosan samples and a composition of chitosan with montmorillonite were formed by casting methods from acetic acid solutions and were soaked in a simulated body fluid (SBF) solution at 37C for 14 days. The samples were compared before and after soaking. The obtained results showed growth of new phases containing calcium in all prepared films

Mechanical Properties of Wood Fiber Reinforced Geopolymer Composites with Sand Addition

Fly ash-based geopolymers can be considered as a greener alternative to ordinary Portland cement, featuring comparable properties and cost yet with lower CO2 emissions. New wood fiber reinforced geopolymer composites with sand addition (WFSGC) have been synthesized at room temperature by mixing powder (fly ash, sand and randomly reinforced wood fiber) with sodium silicate and sodium hydroxide as alkaline activators. New WFSGC were cured at 90°C for 24 h. The design and investigation of WFSGC were based on a fix 5 wt.% percentage of sand, with variable wood fiber (5, 10, 15, 20, 25, 30 and 35 wt.%) and fly ash percentages. These WFSGC showed decreasing mechanical properties with increasing wood fiber addition as measured by the compressive strength at the cylindrical test (21.76–42.52 MPa), the compressive strength at the cubic test (31.79–39.17 MPa), the force load at upper yield at the cylindrical test (1.27–3.58KN), the flexural strength (7–10.76 MPa), compressive modulus at the cylindrical test (590,75–1021.17 MPa), the compressive modulus at cubic test (787.92–1059.79 MPa) and the flexural modulus (298.03–737.83 MPa). The density of WFRGC decreases with the addition of wood fiber (1.49–1.71 g/cm3). WFSGC with addition wood fibers up to 15 wt.% could be the limit for a promising green material for construction

Preface

3 pagesInternational audienc

Recent Advances on the Design and Applications of Antimicrobial Nanomaterials

Present worldwide difficulties in healthcare and the environment have motivated the investigation and research of novel materials in an effort to find novel techniques to address the current challenges and requirements. In particular, the use of nanomaterials has demonstrated a significant promise in the fight against bacterial infections and the problem of antibiotic resistance. Metal nanoparticles and carbon-based nanomaterials in particular have been highlighted for their exceptional abilities to inhibit many types of bacteria and pathogens. In order for these materials to be as effective as possible, synthetic techniques are crucial. Therefore, in this review article, we highlight some recent developments in the design and synthesis of various nanomaterials, including metal nanoparticles (e.g., Ag, Zn, or Cu), metal hybrid nanomaterials, and the synthesis of multi-metallic hybrid nanostructured materials. Following that, examples of these materials’ applications in antimicrobial performance targeted at eradicating multi-drug resistant bacteria, material protection such as microbiologically influenced corrosion (MIC), or additives in construction materials have been described

Biomineralization: from fundamentals to biomaterials & environmental issues.

350 pagesInternational audienc

Advanced Geopolymer-Based Composites for Antimicrobial Application

In most studies about geopolymeric materials used in construction, the antibacterial properties of the building materials are treated as secondary features. Today, antimicrobial properties are a key feature in many building applications. The main objective of this article is to summarize the state-of-the-art in the area of design, development, and applications of nanoparticles as additives to geopolymer composites used in construction to improve their physical mechanical properties and induce a potential antibacterial effect, protecting them against alkali-resistant bacteria. On the basis of the literature and authors’ experience, the most important methods of obtaining especially the porous geopolymers, of nanomaterials used as additives, with potential antibacterial effect but also the potential mechanism of action against bacterial development were presented. The main findings show that using graphene oxide (GO) in geopolymer composites, but also other nanoparticles such as silver (Ag), zinc oxide (ZnO), silica (SiO2), titanium dioxide (TiO2), copper (Cu) as additives, is an effective way to induce a potential antibacterial effect and to improve the physical and mechanical properties in building materials

Electrospun Membranes Based on Polycaprolactone, Nano-Hydroxyapatite and Metronidazole

The aim of this research was to develop new electrospun membranes (EMs) based on polycaprolactone (PCL) with or without metronidazole (MET)/nano-hydroxyapatite (nHAP) content. New nHAP with a mean diameter of 34 nm in length was synthesized. X-ray diffraction (XRD) and attenuated total reflectance Fourier transform infrared spectroscopy (FTIR-ATR) were used for structural characterization of precursors and EMs. The highest mechanical properties (the force at maximum load, Young’s modulus and tensile strength) were found for the PCL membranes, and these properties decreased for the other samples in the following order: 95% PCL + 5% nHAP > 80% PCL + 20% MET > 75% PCL + 5% nHAP + 20% MET. The stiffness increased with the addition of 5 wt.% nHAP. The SEM images of EMs showed randomly oriented bead-free fibers that generated a porous structure with interconnected macropores. The fiber diameter showed values between 2 and 16 µm. The fiber diameter increased with the addition of nHAP filler and decreased when MET was added. New EMs with nHAP and MET could be promising materials for guided bone regeneration or tissue engineering

Antimicrobial Poly (Lactic Acid)/Copper Nanocomposites for Food Packaging Materials

Composites based on polylactic acid (PLA) and copper for food packaging applications were obtained. Copper clusters were synthesized in polyethylene glycols 400 and 600, respectively, using ascorbic acid as a reducing agent, by reactive milling. Copper clusters were characterized by Scanning Electron Microscopy (SEM), Fourier Transform Infrared (FT-IR), and Ultraviolet-Visible (UV-VIS) spectroscopy. Copper/PLA composites containing Proviplast as plasticizer were characterized by FT-IR spectroscopy, mechanical tests, Differential Scanning Calorimetry (DSC), Thermogravimetric Analysis (TGA), absorption of the saline solution, contact angle, and antibacterial properties. It was observed that the concentration of Copper/PEG influenced the investigated properties. The mechanical properties of the samples decreased with the increasing of Copper/PEG concentration. We recorded the phase transformation temperatures and identified the exothermic or endothermic processes. The lowest absorption values were recorded in the case of the sample containing 1% Cu. The contact angle decreases with the increase in the concentration of the PEG 600-Cu mixture in the recipes. The increase in the content of Cu clusters favors the decrease in the temperature, taking place 15% wt mass losses. The obtained composites showed antibacterial properties for all tested strains. These materials could be used as alternative materials for obtaining biodegradable food packaging