344 research outputs found
Analyses of simple and intercooled recuperated direct Brayton helium gas turbine cycles for Generation IV reactor power plants
As a nongreenhouse gas-emitting source, the benefits of nuclear as a main power-generation alternative are yet to be fully explored; part of the reason is due to the significant implementation costs. However, with cycle efficiencies of 45–50% in current studies, it can be argued that the long-term benefits outweigh the initial costs, if developed under the Generation-IV (Gen-IV) framework. The main objective of this study is to analyze the effects of pressure and temperature ratios (TRs) including sensitivity analyses of component efficiencies, ambient temperature, component losses and pressure losses on cycle efficiency and specific work. The results obtained indicate that pressure losses and recuperator effectiveness have the greatest impact on cycle efficiency and specific work. The analyses intend to aid development of the simple cycle recuperated (SCR) and intercooled cycle recuperated (ICR) cycles, applicable to gas-cooled fast reactors (GFRs) and very-high-temperature reactors (VHTRs), in which helium is the coolant
Analyses of long term off-design performance strategy and operation of a high pressure ratio intercooled Brayton helium gas turbine cycle for generation IV nuclear power plants
The Intercooled Cycle (IC) is a simplified novel proposal for Generation IV Nuclear Power Plants (NPP) based on studies demonstrating efficiencies of over 45%. As an alternative to the Simple Cycle Recuperated (SCR) and the Intercooled Cycle Recuperated (ICR), the main difference in configuration is no recuperator, which reduces its size. It is expected that the components of the IC will not operate at optimum part power due to seasonal changes in ambient temperature and grid prioritisation for renewable sources. Thus the ability to demonstrate viable part load performance becomes an important requirement. The main objective of this study is to derive Off-Design Points (ODPs) for a temperature range of -35 to 50°C and COTs between 750 to 1000°C. The ODPs have been calculated using a tool designed for this study. Based on results, the intercooler changes the mass flow rate and compressor pressure ratio. However, a drop of ~9% in plant efficiency, in comparison to the ICR (6%) was observed for pressure losses of up to 5% . The reactor pressure losses for IC has the lowest effect on plant cycle efficiency in comparison to the SCR and ICR. Characteristic maps are created to support first order calculations. It is also proposed to consider the intercooler pressure loss as a handle for ODP performance. The analyses brings attention to the IC an alternative cycle and aids development of cycles for Generation IV Nuclear Power Plants specifically Gas Cooled Fast Reactors (GFRs) and Very High Temperature Reactors (VHTRs)
Analyses of the control system strategies and methodology for part power control of the simple and intercooled recuperated Brayton helium gas turbine cycles for generation IV nuclear power plants
An important requirement for Generation IV Nuclear Power Plant (NPP) design is the control system, which enables part power operability. The choices of control system methods must ensure variation of load without severe drawbacks on cycle performance. The objective of this study is to assess the control of the NPP under part power operations. The cycles of interest are the Simple Cycle Recuperated (SCR) and the Intercooled Cycle Recuperated (ICR). Control strategies are proposed for NPPs but the focus is on the strategies that result in part power operation using the inventory control method. Firstly, results explaining the performance and load limiting factors of the inventory control method are documented; subsequently, the transient part power performances. The load versus efficiency curves were also derived from varying the load to understand the efficiency penalties. This is carried out using a modelling and performance simulation tool designed for this study. Results show that the ICR takes ~102% longer than the SCR to reduce the load to 50% in Design Point (DP) performance conditions for similar valve flows, which correlates to the volumetric increase for the ICR inventory tank. The efficiency penalties are comparable for both cycles at 50% part power, whereby a 22% drop in cycle efficiency was observed and indicates limiting time at very low part power. The analyses intend to aid the development of cycles for Generation IV NPPs specifically Gas Cooled Fast Reactors (GFRs) and Very High Temperature Reactors (VHTRs), where helium is the coolant
A review of the turbine cooling fraction for very high turbine entry temperature helium gas turbine cycles for Generation IV reactor power plants
The potential for high Turbine Entry Temperatures (TET) turbines for Nuclear Power Plants (NPPs) require improved materials and sophisticated cooling. Cooling is critical to maintaining mechanical integrity of the turbine for temperatures >1000°C. Increasing TET is one of the solutions for improving efficiency after cycle optimum pressure ratios have been achieved but cooling as a percentage of mass flow will have to increase, resulting in cycle efficiency penalties. To limit this effect, it is necessary to know the maximum allowable blade metal temperature to ensure the minimum cooling fraction is used. The main objective of this study is to analyse the thermal efficiencies of four cycles in the 300 – 700 MW class for Generation IV NPPs, using two different turbines with optimum cooling for TETs between 950°C - 1200°C. The cycles analysed are Simple Cycle (SC), Simple Cycle Recuperated (SCR), Intercooled Cycle (IC) and Intercooled Cycle Recuperated (ICR). Although results showed that deterioration of cycle performance is lower when using improved turbine material, the justification to use optimum cooling improves the cycle significantly when a recuperator is used. Furthermore, optimised cooling flow and the introduction of an intercooler improves cycle efficiency by >3%, which is >1% more than previous studies. Finally, the study highlights the potential of cycle performance beyond 1200°C for IC. This is based on the IC showing the least performance deterioration. The analyses intend to aid development of cycles for deployment in Gas Cooled Fast Reactors (GFRs) and Very High Temperature Reactors (VHTRs)
Analyses of a high pressure ratio intercooled direct Brayton helium gas turbine cycle for Generation IV reactor power plants
The intercooled cycle (IC) as an alternative to the simple cycle recuperated (SCR) and intercooled cycle recuperated (ICR) is yet to be fully analyzed for the purpose of assessing its viability for utilization within Generation IV nuclear power plants (NPPs). Although the benefits are not explicitly obvious, it offers the advantage of a very high overall pressure ratio (OPR) in the absence of a recuperator. Thus, the main objective of this study is to analyze various pressure ratio configurations, the effects of varying pressure ratio including sensitivity analyses of component efficiencies, ambient temperature, component losses and pressure losses on cycle efficiency, and specific work of the IC, including comparison with the SCR and ICR. Results of comparison between the IC and the SCR and ICR derived that the cycle efficiencies are greater than the IC by ∼4%∼4% (SCR) and ∼6%∼6% (ICR), respectively. However, the pressure losses for IC are lower when compared with the SCR and ICR. Nonetheless, heat from the turbine exit temperature of the IC can be used in a processing plant including the possibility of higher turbine entry temperatures (TETs) to significantly increase the cycle efficiency in a bid to justify the business case. The analyses intend to bring to attention an alternative to current cycle configurations for the gas-cooled fast reactors (GFRs) and very-high-temperature reactors (VHTRs), where helium is the coolant. The findings are summarized by evaluating the chosen pressure ratio configurations against critical parameters and detailed comparison with the SCR and ICR
Analyses of the effect of cycle inlet temperature on the precooler and plant efficiency of the simple and intercooled helium gas turbine cycles for generation IV nuclear power plants
Nuclear Power Plant (NPP) precooler coolant temperature is critical to performance because it impacts the work required to increase the coolant pressure. Variation of the coolant temperature results in varied precooler hot gas temperatures, which are cooled before re-entry. For recirculation, the heat sink (usually sea water), could exit the precooler at unfavourable temperatures and impact the re-entering coolant, if not recirculated properly at the source. The study objective is to analyse the effects of coolant inlet temperature on the heat sink and cycle efficiency. The cycles are Simple Cycle Recuperated (SCR), Intercooler Cycle Recuperated (ICR), and Intercooled Cycle without Recuperation (IC). Results show that the co-current precooler provides favourable outlet heat sink temperatures but compromises compactness. For a similar technology level, the counter-current precooler yields excessive heat sink outlet temperatures due to a compact, robust, and efficient heat transfer design, but could be detrimental to precooler integrity due to corrosion, including the cycle performance, if not recirculated back into the sea effectively. For the counter-current, the ICR has the best heat sink average temperature ratio of 1.4; the SCR has 2.7 and IC has 3.3. The analyses aid the development of Gas Cooled Fast Reactors (GFRs) and Very High Temperature Reactors (VHTRs), where helium is used as the coolant
Effect of change in role of an aircraft on engine life
New aircraft require years of development from concept to realisation and can be prone to delays. Consequently, military operators take existing fleets and operate them in a different role. The objective of this study is to examine the effect of operating a typical low bypass military fast jet engine, originally designed for a European theatre, in a hot and harsh climate. The specific purpose is to determine the effect on the high-pressure turbine blade life and the life- cycle cost of the engine.
A mission profile and respective performance conditions were analysed and modelled using an in-house performance tool. The flow conditions were simulated using ANSYS® FLUENT. A conjugated heat transfer solution was adopted to determine the blade metal temperature. The blade was modelled physically in 3D using SIMULIA® ABAQUS FEA software. The stresses were derived and used to calculate the temperature coupled low cycle fatigue and creep life.
A deterioration case was also studied to evaluate the effect of sand and dust ingestion. There was a significant life reduction of approximately 50% due to creep. The reduction in life was inversely proportional to the life cycle cost of the engine depending on the operating conditions. The results were compared with similar engines and summarised in the context of airworthiness regulations and component integrity
Analyses of the costs associated with very high turbine entry temperatures in helium recuperated gas turbine cycles for Generation IV nuclear power plants
Previous analyses of Generation IV (GEN IV) helium gas turbine cycles indicated the possibility for high Turbine Entry Temperatures (TETs) up to 1200°C in order to improve cycle efficiency, using improved turbine blade material and optimum turbine cooling fractions. The purpose of this paper is to understand the effect on the Levelised Unit Electricity Cost (LUEC) of the Nuclear Power Plant (NPP), when the TET is increased to 1200°C from an original TET of 950°C and when an improved turbine blade material is used to reduced the turbine cooling fraction. The analyses focus on the Simple Cycle Recuperated (SCR) and the Intercooled Cycle Recuperated (ICR). The baseline LUECs of the NPPs were calculated as 62.16/MWh for a TET of 950°C. The effect of changing the turbine blades improved the allowable blade metal temperature by 15% with a reduction in the LUEC by 0.6% (SCR) and 0.7% (ICR). Furthermore, increasing the TET to 1200°C has a significant effect on the power output but more importantly it reduces the LUECs by 22.7% (SCR) and 19.8% (ICR). The analyses intends to aid development of the SCR and ICR including improving the decision making process on choice of cycles applicable to the Gas-cooled Fast Reactors (GFRs) and Very High-Temperature Reactors (VHTRs), where helium is the coolant
Analyses of the load following capabilities of Brayton Helium gas turbine cycles for generation IV nuclear power plants
The control system for Generation IV Nuclear Power Plant (NPP) design must ensure load variation when changes to critical parameters affect grid demand, plant efficiency and component integrity. The objective of this study is to assess the load following capabilities of cycles when inventory pressure control is utilised. Cycles of interest are Simple Cycle Recuperated (SCR), Intercooled Cycle Recuperated (ICR) and Intercooled Cycle without recuperation (IC). Firstly, part power performance of the IC is compared to results of the SCR and ICR. Subsequently, the load following capabilities are assessed when the cycle inlet temperature is varied. This was carried out using a tool designed for this study. Results show that the IC takes ~2.7% longer than the ICR to reduce the power output to 50% when operating in Design Point (DP) for similar valve flows, which correlates to the volumetric increase for the IC inventory storage tank. However, the ability of the IC to match the ICR’s load following capabilities is severely hindered because the IC is most susceptible to temperature variation. Furthermore, the IC takes longer than the SCR and ICR to regulate the reactor power by a factor of 51 but this is severely reduced, when regulating NPP power output. However, the IC is the only cycle that does not compromise reactor integrity and cycle efficiency when regulating the power. The analyses intend to aid the development of cycles specifically Gas Cooled Fast Reactors (GFRs) and Very High Temperature Reactors (VHTRs), where helium is the coolant
Beyond Marcus theory and the Landauer-Büttiker approach in molecular junctions: A unified framework.
Charge transport through molecular junctions is often described either as a purely coherent or a purely classical phenomenon, and described using the Landauer-Büttiker formalism or Marcus theory (MT), respectively. Using a generalised quantum master equation, we here derive an expression for current through a molecular junction modelled as a single electronic level coupled with a collection of thermalised vibrational modes. We demonstrate that the aforementioned theoretical approaches can be viewed as two limiting cases of this more general expression and present a series of approximations of this result valid at higher temperatures. We find that MT is often insufficient in describing the molecular charge transport characteristics and gives rise to a number of artefacts, especially at lower temperatures. Alternative expressions, retaining its mathematical simplicity, but rectifying those shortcomings, are suggested. In particular, we show how lifetime broadening can be consistently incorporated into MT, and we derive a low-temperature correction to the semi-classical Marcus hopping rates. Our results are applied to examples building on phenomenological as well as microscopically motivated electron-vibrational coupling. We expect them to be particularly useful in experimental studies of charge transport through single-molecule junctions as well as self-assembled monolayers
- …