87 research outputs found
Effect of the Static Strength of a Metal on Long-Rod Penetration at Low Velocities
The effect of the static strength (yield stress) of a material on major penetration parameters (specific work of deformation and penetration force determined by the pressure at the rod-cavity contact surface) was examined. The analytical equations and quantitative estimates of specific work spent for formation of spherical and cylindrical cavities and of the pressure at the surface of such cavities at their static expansion were obtained for the rigidplastic and elastoplastic models of the material. The estimates of specific work of deformation at the formation of the spherical cavity in the plate and of the penetration of a rigid rod are shown to be adequate. The influence of strain hardening on a maximum radial stress on the cavity surface was evaluated. The resistance to penetration and the expansion of a cavity are shown to be strongly influenced by the elastic compressibility of a material in the inelastic region at low penetration velocities. The kinetics of the stress-strain state of the material at the formation of the cavity was analyzed for the case of considerable deformation of a rod at penetration.Рассмотрено влияние статической прочности (предела текучести) материала на основные параметры процесса проникания - удельную работу образования каверны и давление на поверхности контакта. Получены аналитические выражения и количественные оценки удельной работы, затраченной на образование сферической и цилиндрической каверн, и давления на поверхности таких каверн при их статическом расширении для жесткопластической и упругопластической моделей материала. Показана адекватность оценок удельной работы деформирования пластины при образовании сферической каверны и при образовании каверны в результате проникания жесткого стержня. Оценено влияние деформационного упрочнения материала на максимальное радиальное напряжение на поверхности каверны. Показано, что при низких скоростях проникания существенное влияние на сопротивление прониканию и расширение каверны оказывает упругая сжимаемость материала в области неупругих деформаций. Проведен анализ кинетики напряженно-деформированного состояния материала при проникании деформируемого стержня
Pulse Current Treatment Effect on the Strength of Reinforcing Steel and Its Weld Joint under Impact Loading
Приведены результаты испытаний на статическое и ударное растяжение образцов из строительной арматурной стали в состоянии поставки, образцов со стыковым сварным соединением в рабочей части, а также образцов, предварительно обработанных пропусканием импульсного электрического тока высокой плотности. Показано, что повышенная скорость деформации вызывает увеличение прочности, а обработка импульсным электрическим током существенно влияет на прочность и пластичность металла с дефектами в области сварного шва как при статическом, так и при ударном растяжении.Наведено результати випробувань на статичний та ударний розтяг зразків із будівельної сталі у стані поставки, зразків зі стиковим зварним з’єднанням у робочій частині та зразків, що попередньо обробляли пропусканням імпульсного електричного струму високої густини. Показано, що підвищена швидкість деформації призводить до збільшення міцності, а обробка імпульсним електричним струмом суттєво впливає на міцність і пластичність металу з дефектами в області зварного шва як за статичного, так і ударного розтягу.We present results o f static and impact tension tests o f as-received reinforcing steel specimens, specimens with weld joints in their test portion, as well as specimens pretreated by high-density pulse current. As test results demonstrate, an increased strain rate enhances strength, and the pulse current treatment greatly influences the strength and plasticity o f a defect-containing weld metal under static and impact tension
Experimental evaluation of pulse electric current effect on residual stresses in composite-to-copper joints
Experimental method for evaluation of residual stress distribution in carbon fiber reinforced carbon composite jointed to copper is presented. Pulse electric current passed through composite-to-copper joint essentially reduces the level of residual stresses.Представлено експериментальну методику щодо оцінки розподілу залишко вих напружень у з’єднанні композита (вуглець, зміцнений вуглецевими волокнами) з міддю. Установлено, що імпульс електричного струму, що пропущений через з’єднання композит-мідь, суттєво зменшує рівень залиш кових напружень.Представлена экспериментальная методика оценки распределения остаточных напряжений в соединении композита (углерод, упрочненный углеродными волокнами) с медью. Установлено, что импульс электрического тока, пропущенный через соединение композит-медь, существенно снижает уровень остаточных напряжений
Evaluation of Residual Stresses in Carbon/Carbon Composites Components Joined to Copper before and after Pulse Electromagnetic Treatment
Приведены результаты расчетно-экспериментальной оценки остаточных напряжений в компонентах, полученных соединениемкомпозита (углерод, упрочненный углеродными волокнами) с медью. Установлено, что импульсная электромагнитная обработка соединения уменьшает уровень остаточных напряжений.Наведено результати розрахунково-експериментальної оцінки залишкових напружень у компонентах, що отримані з’єднуванням композита (вуглець, зміцнений вуглецевими волокнами) з міддю. Установлено, що імпульсна електромагнітна обробка з’єднання зменшує рівень залишкових напружень
Study of the radiative decay with CMD-2 detector
Using the of data collected with the CMD-2 detector at VEPP-2M
the decay mode , has been
studied. The obtained branching ratio is B(.Comment: 13 pages, 5 figures, LaTex2e, to be published in Phys. Lett.
Observation of semileptonic decays with CMD-2 detector
The decay has been observed by the CMD-2 detector at
the e^+e^- collider VEPP-2M at Novosibirsk. Of 6 million produced
pairs, events of the decay were selected. The
corresponding branching ratio is . This result is consistent with the evaluation of from the semileptonic rate and lifetime
assuming .Comment: 7 pages, 6 figures, LaTex2e. Submitted to Phys.Lett.
Measurement of omega meson parameters in pi^+pi^-pi^0 decay mode with CMD-2
About 11 200 e^+e^- -> omega -> pi^+pi^-pi^0 events selected in the center of
mass energy range from 760 to 810 MeV were used for the measurement of the
\omega meson parameters. The following results have been obtained: sigma
_{0}=(1457 \pm 23 \pm 19)nb, m_{\omega}=(782.71 \pm 0.07 \pm 0.04) MeV/c^{2},
\Gamma_{\omega}=(8.68 \pm 0.23 \pm 0.10) MeV,
\Gamma_{e^+e^-}\cdot Br (\omega -> pi^+pi^-pi^0)=
(0.528 \pm 0.012 \pm 0.007) \cdot 10^{-3} MeV.Comment: 8 pages, 4 figure
Study of the process e+e- to pi+pi-pi+pi-pi0 with CMD-2 detector
The process e+e- to pi+ pi- pi+ pi- pi0 has been studied in the center of
mass energy range 1280 -- 1380 MeV using 3.0 1/pb of data collected with the
CMD-2 detector in Novosibirsk. Analysis shows that the cross section of the
five pion production is dominated by the contributions of the eta pi+pi- and
omega pi+pi- intermediate states.Comment: 8 pages, 3 figure. Submitted to Phys. Lett.
Study of the Process in the C.M.Energy Range 1.05-1.38 GeV with CMD-2
The process has been studied with the CMD-2 detector
using about 950 events detected in the center-of-mass energy range from 1.05 to
1.38 GeV. The cross section exceeds the expectation based on the contributions
of the rho(770), omega(782) and phi(1020) mesons only.Comment: 12 pages, 3 figures, uses elsart.cls, submitted to Physics Letters
Observation of the conversion decay at CMD-2
Using 15.1^{-1} of data collected by CMD-2 in the -meson energy range,
the branching ratio of the conversion decay has been
measured for the first time: B(\phi\to\pi^0e^+e^-) = (1.22 \pm 0.34 \pm 0.21)
\cdot 10 ^{-5}.Comment: 13 pages, 6 PostScript figures, uses refmerge.sty. To be published in
Phys. Lett.
- …