Evaluation of median mandibular flexure values in dentulous and edentulous subjects by using an intraoral digital scanner

PURPOSE. Mandibular flexure is a crucial phenomenon that may affect the success of rigid bilateral mandibular prosthetic treatment. The aim of this study was to determine the amount of median mandibular flexure (MMF) that occurs during mouth opening from anterior to posterior mandible in seven different regions, in different age and gender groups of both dentulous and edentulous subjects, using an intraoral digital scanner. MATERIALS AND METHODS. In this study, the mandibular arch of 56 dentulous and 35 edentulous individuals were scanned with an intraoral scanner at both the minimum mouth opening (MnMO) and the maximum mouth opening (MxMO). MMF values were calculated by subtracting the distance value at the MxMO from the distance between the reference points at the MnMO at seven different mandibular regions of dentulous and edentulous subjects. In addition, the left and right side MMF values were measured. All data were analyzed statistically (alpha = .05). RESULTS. MMF value increased linearly from anterior to posterior mandible in both dentulous and edentulous individuals. The differences in MMF values were not statistically significant according to side (left/right), age, or gender (P > .05). No significant differences were found between the mean MMF values of the same region in both dentulous and edentulous individuals (P > .05). CONCLUSION. MMF was seen in different regions of the mandibles of both edentulous and dentulous individuals measured at the MxMO. Mandibular flexure should be considered for the success and prognosis of the long-span and rigid prostheses

Wear of MgO-CaO- SiO

Wear of a glass-ceramic produced through controlled crystallization of a glass in the MgO-CaO-SiO2-P2O5-F system has been evaluated and compared to various commercial dental ceramics including IPS Empress 2, Cergo Pressable Ceramic, Cerco Ceram, and Super porcelain EX-3. Wear tests were performed in accord with the ASTM G99 for wear testing with a pin-on-disk apparatus. The friction coefficient and specific wear rate of the materials investigated were determined at a load of 10 N and at ambient laboratory conditions. Microhardness of the materials was also measured to elucidate the appropriateness of these materials for dental applications

Evaluation of corrosion resistance of Co-Cr alloys fabricated with different metal laser sintering systems

PURPOSE. The aim of this study was to evaluate the corrosion resistance of the specimens produced by five different commercial metal laser sintering (MLS) systems with their recommended Co-Cr alloy powders. MATERIALS AND METHODS. The MLS machines and the alloy powders used were, ProX 100-ST2724G (St-Pro), Mysint 100-EOS SP2 (SP2-Mys), EOSINT 270-EOS SP2 (SP2-EOS), SLM 100-Starbond CoS (SB-SLM), and MLab Cusing-Remanium® Star (RS-MLab), respectively. Eight specimens from each group were prepared. Open circuit potential (Eocp) and electrochemical impedance spectroscopy (EIS) measurements of polished surfaces of the specimens were conducted in a three-electrode cell using a potentiostat-galvanostat in Fusayama-Meyer artificial saliva (AS). Specimens from each group were immersed in AS and de-ionized water for seven days. Eocp, charge transfer resistance (Rct) values, and released ions (?g/cm2 x 7d) in different solutions were determined. The specimen surfaces were observed with SEM/EDS. Results were analyzed statistically. RESULTS. Eocp values have shifted to potentials that are more positive over time. Steady-state Eocp values were from high to low as follows, SB-SLM, SP2-Mys, SP2-EOS, RS-MLab, and ST-Pro, respectively. After 60 mins, RS-MLab specimens had the highest Rct value, followed by SP2-Mys, SB-SLM, SP2-EOS, and ST-Pro. In all groups, ion release was higher in AS than that in de-ionized water. CONCLUSION. There were small differences among the corrosion resistances of the Co-Cr alloy specimens produced with MLS systems; meanwhile, the corrosion resistances were quite high for all specimens. © 2020 The Korean Academy of Prosthodontics

Comparative radiopacity of bone graft materials

The aim of this study was to investigate the radiopacity of bone graft materials (BGMs) in comparison with bovine mandibular cortical bone and human dentine. Eight samples of each material (8 mm in diameter and 3 mm in thickness) were prepared from Dexabone (R) (DB), Bio - Oss (R) (BO), 4BONE SBS (4B), KASIOS (R) TCP (KA), S. C. PONETI (PO), and Apatite-Wollastonite (AW). The optical densities of each material, along with one tooth section (human canine tooth 1 mm slice), bovine mandibular cortical bone (BC) samples, and an aluminum step wedge, were measured from radiographic images using a transmission densitometer. The data were analyzed by nonparametric one-way ANOVA (Kruskal-Wallis) and Duncan's multiple range tests for post hoc comparison (alpha = 0.05). BC and AW had statistically lower optical density values than BO, 4B and human dentine (p 0.05). The radiopacity of all BGMs investigated seemed to be too low to be detected radiographically when placed in the mandibular cortical bone. (C) 2011 European Association for Cranio-Maxillo-Facial Surgery