49,541 research outputs found
A technique for computation of noise temperature due to a beam waveguide shroud
Direct analytical computation of the noise temperature of real beam waveguide (BWG) systems, including all mirrors and the surrounding shroud, is an extremely complex problem and virtually impossible to achieve. Yet the DSN antennas are required to be ultra low-noise in order to be effective, and a reasonably accurate prediction is essential. This article presents a relatively simple technique to compute a real BWG system noise temperature by combining analytical techniques with data from experimental tests. Specific expressions and parameters for X-band (8.45-GHz) BWG noise computation are obtained for DSS 13 and DSS 24, now under construction. These expressions are also valid for various conditions of the BWG feed systems, including horn sizes and positions, and mirror sizes, curvatures, and positions. Parameters for S- and Ka-bands (2.3 and 32.0 GHz) have not been determined; however, those can be obtained following the same procedure as for X-band
A deeper insight into quantum state transfer from an information flux viewpoint
We use the recently introduced concept of information flux in a many-body
register in order to give an alternative viewpoint on quantum state transfer in
linear chains of many spins.Comment: 6 pages, 3 figures, RevTeX
Radiometric tests on wet and dry antenna reflector surface panels
The results of X-band noise temperature tests on two types of antenna surface panels are presented. The first type tested was a solid antenna panel, while the second type was a perforated panel with 3/16-in.-diameter holes. Measurements were made at 8.45 GHz using an X-band radiometric system. Included in this article are measured noise temperature contributions from: (1) thermal diffusive white paint on solid and perforated panels, and (2) water sprayed on both painted and unpainted perforated panels. Experiments on perforated panels were restricted to the 3/16-in.-diameter hole panels formerly used on Deep Space Network 64-m antennas. Rigorous calibration equations, applicable to a variety of antenna panel and dichroic plate test configurations, are presented. It was demonstrated that an accurate, stable radiometric measurement system of the type used for the results of this research makes it possible to obtain information that would be much more difficult to obtain using other techniques
Bypassing state initialization in Hamiltonian tomography on spin-chains
We provide an extensive discussion on a scheme for Hamiltonian tomography of
a spin-chain model that does not require state initialization [Phys. Rev. Lett.
102, 187203 (2009)]. The method has spurred the attention of the physics
community interested in indirect acquisition of information on the dynamics of
quantum many-body systems and represents a genuine instance of a
control-limited quantum protocol.Comment: 7 pages, 2 figures, RevTeX
A note on systems with ordinary and impulsive controls
We investigate an everywhere defined notion of solution for control systems
whose dynamics depend nonlinearly on the control and state and are
affine in the time derivative For this reason, the input which
is allowed to be Lebesgue integrable, is called impulsive, while a second,
bounded measurable control is denominated ordinary. The proposed notion of
solution is derived from a topological (non-metric) characterization of a
former concept of solution which was given in the case when the drift is
-independent. Existence, uniqueness and representation of the solution are
studied, and a close analysis of effects of (possibly infinitely many)
discontinuities on a null set is performed as well.Comment: Article published in IMA J. Math. Control Infor
Dual passband dichroic plate for X-band
A need arose in the Deep Space Network for a dichroic plate that would simultaneously pass two desired frequency bands in the X-band region. In addition, the plate must be totally reflective for S-band frequencies. A dielectrically loaded dichroic plate is described that was developed to meet this need. The unique microwave properties that the new dichroic plate had to possess were: (1) insertion losses of less than 0.04 dB for X-band uplink frequencies centered at 7167 MHz and for X-band downlink frequencies centered at about 8425 MHz; (2) insertion losses that met the low loss requirements at 30 deg incidence angle simultaneously for both parallel and perpendicular polarizations; (3) total reflectivity at S-band frequencies; and (4) ability to maintain these electrical characteristics while passing 100 kW of CW power at X-band or while reflecting 100 kW of CW power at S-band. The dual passband dichroic plate is a thick metallic plate having an array of periodic round holes filled with Teflon plugs. Test results on an experimental prototype plate indicate that it is technically possible to design a dielectrically filled dichroic plate that meets all of the technical requirements
DSS-13 beam waveguide antenna frequency stability
Measurements made on the frequency stability of the DSS-13 34-m diameter Beam Waveguide (BWG) antenna showed that at 46.5 and 37 deg elevation angles, the BWG antenna stability at 12.2 GHz was between 1.3 and 2.2 x 10(exp -15) for tau = 1024 sec and good weather conditions. These frequency stability values apply to the portion of the antenna that includes the main reflector, subreflector, tripod legs, and the six BWG mirrors. The test results reported are believed to be the first known successful measurements of the stability of the microwave optics portion of a large antenna to a level of 1 or 2 parts in 10(exp 15)
- …