78 research outputs found
Negative Particle Planar and Axial Channeling and Channeling Collimation
While information exists on high energy negative particle channeling there
has been little study of the challenges of negative particle bending and
channeling collimation. Partly this is because negative dechanneling lengths
are relatively much shorter. Electrons are not particularly useful for
investigating negative particle channeling effects because their material
interactions are dominated by channeling radiation. Another important factor is
that the current central challenge in channeling collimation is the
proton-proton Large Hadron Collider (LHC) where both beams are positive. On the
other hand in the future the collimation question might reemerge for
electron-positron or muon colliders. Dechanneling lengths increase at higher
energies so that part of the negative particle experimental challenge
diminishes. In the article different approaches to determining negative
dechanneling lengths are reviewed. The more complicated case for axial
channeling is also discussed. Muon channeling as a tool to investigate
dechanneling is also discussed. While it is now possible to study muon
channeling it will probably not illuminate the study of negative dechanneling.Comment: 15 pages, 1 figure, docx fil
Recommended from our members
Progress on a cryogenically cooled RF gun polarized electron source
RF guns have proven useful in multiple accelerator applications. An RF gun capable of producing polarized electrons is an attractive electron source for the ILC or an electron-ion collider. Producing such a gun has proven elusive. The NEA GaAs photocathode needed for polarized electron production is damaged by the vacuum environment in an RF gun. Electron and ion back bombardment can also damage the cathode. These problems must be mitigated before producing an RF gun polarized electron source. In this paper we report continuing efforts to improve the vacuum environment in a normal conducting RF gun by cooling it with liquid nitrogen after a high temperature vacuum bake out. We also report on a design of a cathode preparation chamber to produce bulk GaAs photocathodes for testing in such a gun. Future directions are also discussed
First observation of the exchange of transverse and longitudinal emittances
An experimental program to demonstrate a novel phase space manipulation in
which the horizontal and longitudinal emittances of a particle beam are
exchanged has been completed at the Fermilab A0 Photoinjector. A new beamline,
consisting of a TM110 deflecting mode cavity flanked by two horizontally
dispersive doglegs has been installed. We report on the first direct
observation of transverse and longitudinal emittance exchange
Recommended from our members
Design of the NSLS-II Linac Front End Test Stand
The NSLS-II operational parameters place very stringent requirements on the injection system. Among these are the charge per bunch train at low emittance that is required from the linac along with the uniformity of the charge per bunch along the train. The NSLS-II linac is a 200 MeV linac produced by Research Instruments Gmbh. Part of the strategy for understanding to operation of the injectors is to test the front end of the linac prior to its installation in the facility. The linac front end consists of a 100 kV electron gun, 500 MHz subharmonic prebuncher, focusing solenoids and a suite of diagnostics. The diagnostics in the front end need to be supplemented with an additional suite of diagnostics to fully characterize the beam. In this paper we discuss the design of a test stand to measure the various properties of the beam generated from this section. In particular, the test stand will measure the charge, transverse emittance, energy, energy spread, and bunching performance of the linac front end under all operating conditions of the front end
Recommended from our members
Optical transition radiation interferometry for the A0 photoinjector
Optical Transition Radiation Interferometry (OTRI) is a promising diagnostic technique and has been successfully developed and used for investigation of relativistic beams. For mid-energy accelerators the technique is traditionally based on thin polymer films (the first one is being transparent for visible light), which causes beam multiple scattering of about 1 mrad. A disadvantage of those films is unacceptable vacuum properties for photoinjectors and accelerators using superconducting cavities. We have studied the application of thin mica sheets for the OTRI diagnostics at the A0 Photoinjector in comparison with 2.5 {micro}m thick Mylar films. This diagnostic is also applicable for the ILCTA-NML accelerator test facility that is planned at Fermilab. This report discusses the experimental setups of the OTR interferometer for the A0 Photoinjector and presents comparisons of simulations and measurements obtained using Mylar and mica-based interferometers
Recommended from our members
Beam Diagnostics Using BPM Signals from Injected and Stored Beams in a Storage Ring
Many modern light sources are operating in top-off injection mode or are being upgraded to top-off injection mode. The storage ring always has the stored beam and injected beam for top-off injection mode. So the BPM data is the mixture of both beam positions and the injected beam position cannot be measured directly. We propose to use dedicated wide band BPM electronics in the NSLS II storage ring to retrieve the injected beam trajectory with the singular value decomposition (SVD) method. The beam position monitor (BPM) has the capability to measure bunch-by-bunch beam position. Similar electronics can be used to measure the bunch-by-bunch beam current which is necessary to get the injection beam position. The measurement precision of current needs to be evaluated since button BPM sum signal has position dependence. The injected beam trajectory can be measured and monitored all the time without dumping the stored beam. We can adjust and optimize the injected beam trajectory to maximize the injection efficiency. We can also measure the storage ring acceptance by mapping the injected beam trajectory
OTR interferometry diagnostic for the A0 photoinjector
OTR interferometry (OTRI) is an attractive diagnostic for investigation of relativistic electron beam parameters. The diagnostic is currently under development at the A0 Photoinjector. This diagnostic is also applicable for NML accelerator test facility that will be built at Fermilab. The experimental setup of the OTR Interferometer for the FNAL A0 Photoinjector is described in the report. Results of simulations and measurements are presented and discussed
Recommended from our members
NSLS-II INJECTION STRAIGHT DIAGNOSTICS
The ultra-bright light source being developed by the NSLS-II project will utilize top-up injection and fine tuning of the injection process is mandatory. In this paper we present the diagnostics installed in the injection straight. Its use for commissioning and tuning of the injection cycle is also described. The NSLS-II storage ring will utilize a 9.3 meter long injection straight section shown in Fig. 1. Injection will be preformed with two septa (one pulsed, one DC) and four kickers. The stored beam will be shifted towards the pulsed septum up to IS mm and the nominal distance between centers of the injected and the bumped beam is 9.5mm. The NSLS-II beam position monitors will have turn-by-turn and first-turn capabilities and will be used for the commissioning and tuning the injection process. However, there are three additional BPMs and two beam intercepting OTR screens (flags) installed in the injection straight
- …