Thermomechanical Behavior of the HL-LHC 11 Tesla Nb3Sn Magnet Coil Constituents during Reaction Heat Treatment

The knowledge of the temperature induced changes of the superconductor volume, and of the thermo-mechanical behaviour of the different coil and tooling materials is required for predicting the coil geometry and the stress distribution in the coil after the Nb3Sn reaction heat treatment. In the present study we have measured the Young's and shear moduli of the HL-LHC 11 T Nb3Sn dipole magnet coil and reaction tool constituents during in situ heat cycles with the dynamic resonance method. The thermal expansion behaviours of the coil components and of a free standing Nb3Sn wire were compared based on dilation experiments.Comment: 6 pages, 12 figures, presented at MT25 conferenc

Geometry and Alignment Requirements for the LHC Main Dipole

The 15 m long LHC superconducting dipole magnets, which contain two beam channels in a common mechanical structure, produce a magnetic field of 8.3 T required to deflect protons with 7 TeV/c momentum along a circular trajectory in the already existing LEP tunnel. The dipoles are bent in their horizontal plane to provide the largest possible mechanical aperture to the circulating beam. This paper describes the theoretical geometry of the dipole cold mass and the alignment requirements, which are imposed to satisfy the demands of LHC machine operation. A short description of the measuring and alignment procedures and of the measuring instruments is given. Results of a small series of prototype cold masses are presented and discussed

Metrology of the LHC Dipole Cold Masses

In order to provide the largest possible mechanical aperture for the LHC beam, the dipole cold masses have to match the circular trajectory of the particle beam. The requirements on the dipole cold mass geometry are dictated by the beam optics of the LHC machine and by the mechanical deformation limits of the interconnection zone. The geometry of the approximately 15 m long, 0.57 m diameter and 30 t weight dipole cold mass is verified by the measurement of the axes of the cold bore tubes. The tight tolerances imposed, necessitate the use of a high accuracy 3D measuring system based on optical methods. During the last 2 years, 6 prototypes and 4 pre-series magnets have been assembled at CERN. The summary of the results obtained on these cold masses is presented, as well as the evolution of the tooling and the measuring method

Partial cricotracheal resection for pediatric subglottic stenosis: a single institution's experience in 60 cases

Abstract.: In our study, 60 infants and children, each with a severe subglottic stenosis (SGS), underwent partial cricotracheal resection (PCTR) with primary thyrotracheal anastomosis. According to the Myer-Cotton classification, two were grade II, 41 were grade III and 17 were grade IV stenoses. Of the 60 patients, 57 (95%) are presently decannulated, and one patient sustained a complete restenosis. Two patients with better than 80% subglottic airways still are waiting for decannulation: one because of bilateral cricoarytenoid joint fixation and the second because of temporary stenting of the subglottis with a Montgomery T-tube. The rate of decannulation is 97% (36 of 37 cases) in primary PCTRs, 100% (13 of 13 cases) in salvage PCTRs for failed laryngotracheal reconstructions (LTR) and 70% (7 of 10 cases) in extended PCTRs (i.e., PCTR associated with an additional open-airway procedure

Impact of the 3D source geometry on time-delay measurements of lensed type-Ia Supernovae

It has recently been proposed that gravitationally lensed type-Ia supernovae can provide microlensing-free time-delay measurements provided that the measurement is taken during the achromatic expansion phase of the explosion and that color light curves are used rather than single-band light curves. If verified, this would provide both precise and accurate time-delay measurements, making lensed type-Ia supernovae a new golden standard for time-delay cosmography. However, the 3D geometry of the expanding shell can introduce an additional bias that has not yet been fully explored. In this work, we present and discuss the impact of this effect on time-delay cosmography with lensed supernovae and find that on average it leads to a bias of a few tenths of a day for individual lensed systems. This is negligible in view of the cosmological time delays predicted for typical lensed type-Ia supernovae but not for the specific case of the recently discovered type-Ia supernova iPTF16geu, whose time delays are expected to be smaller than a day.Comment: 7 pages, 4 figures, published in A&

Definitive Evidence for Order-by-Quantum-Disorder in Er2Ti2O7

Here we establish the systematic existence of a U(1) degeneracy of all symmetry-allowed Hamiltonians quadratic in the spins on the pyrochlore lattice, at the mean-field level. By extracting the Hamiltonian of Er2Ti2O7 from inelastic neutron scattering measurements, we then show that the U(1)-degenerate states of Er2Ti2O7 are its classical ground states, and unambiguously show that quantum fluctuations break the degeneracy in a way which is confirmed by experiment. This is the first definitive observation of order-by-disorder in any material. We provide further verifiable consequences of this phenomenon, and several additional comparisons between theory and experiment.Comment: 4.5 pages, 3 figures, 7.5 pages of Supplemental Material, 8 supplemental figure

A powder metallurgy austenitic stainless steel for application at very low temperatures

The Large Hadron Collider to be built at CERN will require 1232 superconducting dipole magnets operating at 1.9 K. By virtue of their mechanical properties, weldability and improved austenite stability, nitrogen enriched austenitic stainless steels have been chosen as the material for several of the structural components of these magnets. Powder Metallurgy (PM) could represent an attractive production technique for components of complex shape for which dimension tolerances, dimensional stability, weldability are key issues during fabrication, and mechanical properties, ductility and leak tightness have to be guaranteed during operation. PM Hot Isostatic Pressed test plates and prototype components of 316LN-type grade have been produced by Santasalo Powdermet Oy. They have been fully characterized and mechanically tested down to 4.2 K at CERN. The fine grained structure, the absence of residual stresses, the full isotropy of mechanical properties associated to the low level of Prior Particle Boundaries oxides resulted in superior mechanical properties and high ductility down to liquid helium temperature. The ready weldability and the leak tightness of the alloy have been demonstrated. The properties measured on test plates are comparable to those found in real components, such as prototype end covers fabricated by the same PM technique

Effects of an entomopathogenic fungus on the reproductive potential of Drosophila males.

While mortality is often the primary focus of pathogen virulence, non-lethal consequences, particularly for male reproductive fitness, are less understood; however, they are essential for understanding how sexual selection contributes to promoting resistance. We investigated how the fungal pathogen Metarhizium brunneum affects mating ability, fertility, and seminal fluid protein (SFP) expression of male Drosophila melanogaster paired with highly receptive virgin females in non-competitive settings. Depending on sex and dose, there was a 3-6-day incubation period after infection, followed by an abrupt onset of mortality. Meanwhile, the immune response was strongly induced already 38 h after infection and continued to increase as infection progressed. Latency to mate somewhat increased during the incubation period compared to sham-treated males, but even on Day 5 post infection >90% of infected males mated within 2 h. During the incubation period, M. brunneum infection reduced male reproductive potential (the number of offspring sired without mate limitation) by 11%, with no clear increase over time. Approaching the end of the incubation period, infected males had lower ability to convert number of mating opportunities into number of offspring. After repeated mating, infected males had lower SFP expression than sham controls, more so in males that mated with few mates 24 h earlier. Overall, despite strong activation of the immune response, males' mating ability and fertility remained surprisingly little affected by the fungal infection, even shortly before the onset of mortality. This suggests that the selection for resistance acts mainly through mortality, and the scope for fertility selection to enhance resistance in non-competing settings is rather limited

The LHC Dipole Geometry as Built in Industry

The LHC dipoles magnets are produced in 5 industrial production sites in Europe. The production is well underway and more than half of the total quantity has been delivered to CERN. One of the important characteristics of the dipole magnets is their geometry. To achieve the requested mechanical tolerances on the magnets, which are 15 m long and have a 28 t mass, the final assembly operations includes precise optical measurements. To ensure the good quality and high production rate, the final assembly procedure has been automated as much as possible. The authors report here about the assembly procedure, the features of the software that guides the optical measurements (and consequently the assembly operations) and the results obtained on the geometry in the different sites

Measurement and Analysis of Axial End Forces in a Full-Length Prototype of LHC Main Dipole Magnets

A full-length, twin aperture prototype (MBP2N1) dipole magnet for the LHC project was assembled at CERN with collared coils delivered by industry. The design of this prototype is close to that foreseen for the dipole series manufacture as far the coil geometry and that of the yoke components are concerned. The bolts that transfer the axial magnetic forces from the coil ends to the cold mass end plates were instrumented to verify the axial coil support. These axial forces were initially measured after partial assembly, during a standard and an accelerated cool down Introduction to 1.9 K, and during magnet excitation up to 9.2 T. High force levels were observed, triggering a comparison with analytical models and measurements routinely made on 1-m single aperture dipole models. The prototype magnet was re-assembled with lower initial axial force settings and with additional instrumentation, to monitor these forces during the entire assembly process, and re-tested, to possibly correlate axial forces with training behaviour. This paper reports about the experimental observations and provides models towards their understandin