PrFeO3 Photocathodes Prepared Through Spray Pyrolysis

Perovskite oxides are receiving wide interest for photocatalytic and photoelectrochemical devices, owing to their suitable band gaps for solar light absorption and stability in aqueous applications. Herein, we assess the activity of PrFeO3 photocathodes prepared by using spray pyrolysis and calcination temperatures between 500 and 700 °C. Scanning electron microscopy shows corrugated films of high surface coverage on the conductive glass substrate. The electrochemically active surface area shows slight decreases with temperature increases from 500 to 600 and 700 °C. However, transient photocurrent responses and impedance spectroscopy data showed that films calcined at higher temperatures reduced the probabilities of recombination due to trap states, resulting in faster rates of charge extraction. In this trade‐off, a calcination temperature of 600 °C provided a maximum photocurrent of ‐130±4 μA cm−2 at +0.43 VRHE under simulated sunlight, with an incident photon‐to‐current conversion efficiency of 6.6 % at +0.61 VRHE and 350 nm and an onset potential of +1.4 VRHE for cathodic photocurrent

Shape-Controlled Synthesis of Cu3TeO6 Nanoparticles with Photocatalytic Features

Cu3TeO6 (CTO) has been synthesized by hydrothermal synthesis applying different pH values without any template or a calcination step to control the crystalline phase and the morphology of nanoparticles. The physicochemical properties characterized by X-ray diffraction, field emission scanning electron microscopy, transmission electron microscopy, N2 adsorption, X-ray photoelectron spectroscopy, and diffuse reflectance ultraviolet–visible (DRUV–vis) spectroscopy techniques revealed that the pH values significantly influence the crystal growth. In acidic media (pH = 2), crystal growth has not been achieved. At pH = 4, the yield is low (10%), and the CTO presents irregular morphology. At pH = 6, the yield increases (up to 71%) obtaining an agglomeration of nanoparticles into spherical morphology. At basic conditions (pH = 8), the yield increases up to 90% and the morphology is the same as the sample obtained at pH = 6. At high basic conditions (pH = 10), the yield is similar (92%), although the morphology changes totally to dispersed nanoparticles. Importantly, the as-prepared CTO semiconductor presents photocatalytic activity for H2 production using triethanolamine as a sacrificial agent under visible light illumination. The results also revealed that the nanoparticles agglomerated in a spherical morphology with larger surface area presented almost double activities in H2 production compared to heterogeneously sized particles. These results highlight the suitable optoelectronic properties, including optical band gap, energy levels, and photoconductivity of CTO semiconductors for their use in photocatalytic H2 production.JFC thanks MARSALAS21-09 grant funded by MCIN/AEI/10.13039/501100011033 and European Union NextGeneration EU/PRTR. S.E. and M.D. thank the EPSRC grant EP/S030727/1 for financial support. Financial support from the ERC (European Research Council) Consolidator Grant CATCH (grant agreement no 101002219) is also acknowledged

Autonomous self-healing structural composites with bio-inspired design

Strong and tough natural composites such as bone, silk or nacre are often built from stiff blocks bound together using thin interfacial soft layers that can also provide sacrificial bonds for self-repair. Here we show that it is possible exploit this design in order to create self-healing structural composites by using thin supramolecular polymer interfaces between ceramic blocks. We have built model brick-and-mortar structures with ceramic contents above 95 vol% that exhibit strengths of the order of MPa (three orders of magnitude higher than the interfacial polymer) and fracture energies that are two orders of magnitude higher than those of the glass bricks. More importantly, these properties can be fully recovered after fracture without using external stimuli or delivering healing agents. This approach demonstrates a very promising route towards the design of strong, ideal self-healing materials able to self-repair repeatedly without degradation or external stimuli

Efficient hematite photoanodes prepared by hydrochloric acid-treated solutions with amphiphilic graft copolymer

Porous frameworks of iron oxide (Fe2O3) were prepared by templating with a hydrophobic-hydrophilic graft co-polymer which showed high generated photocurrents under sunlight equivalent illumination. This dataset contains the TEM (transmission electron microscopy) and SEM (scanning electron microscopy) images and raw infrared data.Photocurrent Densities were calculated from generated potential under illumination (at 1 sun equivalent) measured with an Ivium potentiostat and using Ivium Technologies IviumSoft software Release 2.031. Further methodological details may be found in the Experimental Section of the associated manuscript.Data was collected using the PhotoElectroChemical apparatus located in a research laboratory of Dr Salvador Eslava located in Dept of Chemical Engineering, University of Bath. Electron microscopy was conducted at the Microscopy and Analysis Suite, University of Bath. An Ivium Compactstat pontentiostat with associated illumination apparatus and quartz sample cell were employed for photocurrent measurements

A facile way to produce epoxy nanocomposites having excellent thermal conductivity with low contents of reduced graphene oxide

A well-dispersed phase of exfoliated graphene oxide (GO) nanosheets was initially prepared in water. This was concentrated by centrifugation and was mixed with a liquid epoxy resin. The remaining water was removed by evaporation, leaving a GO dispersion in epoxy resin. A stoichiometric amount of an anhydride curing agent was added to this epoxy-resin mixture containing the GO nanosheets, which was then cured at 90 C for 1 h followed by 160 C for 2 h. A second thermal treatment step of 200 C for 30 min was then undertaken to reduce further the GO in situ in the epoxy nanocomposite. An examination of the morphology of such nanocomposites containing reduced graphene oxide (rGO) revealed that a very good dispersion of rGO was achieved throughout the epoxy polymer. Various thermal and mechanical properties of the epoxy nanocomposites were measured, and the most noteworthy finding was a remarkable increase in the thermal conductivity when relatively very low contents of rGO were present. For example, a value of 0.25 W/mK was measured at 30 C for the nanocomposite with merely 0.06 weight percentage (wt%) of rGO present, which represents an increase of *40% compared with that of the unmodified epoxy polymer. This value represents one of the largest increases in the thermal conductivity per wt% of added rGO yet reported. These observations have been attributed to the excellent dispersion of rGO achieved in these nanocomposites made via this facile production method. The present results show that it is now possible to tune the properties of an epoxy polymer with a simple and viable method of GO addition. A

Nanostructured WO₃ photoanodes for efficient water splitting via anodisation in citric acid

We report the production of nanostructured WO3 photoanodes for solar water splitting produced via anodisation using for the first time citric acid, a safer and more environmentally friendly alternative to fluoride-based electrolytes.</p