5 research outputs found
FESTIG KElTSBERECHNUNG NICHT ROTATIONS SYMMETRISCHER FLIESSPRESSMATRIZEN
Regarding the cold forging dies having a polygon hole as a problem of two-dimensional
elasticity and solving the task with Muskhelishvili's method, the stress distribution of dies
can be determined. The article presents the change of the permissible greatest load of a die
having a hexagon hole as a function of the outside diameters of the die and the corner radius
of the hole. The obtained loadibilitv curves are similar to that of dies having cylindrical hole
and by increasing the outside diameter tend for the limit value depending on the corner radius
asymptoticaly
NUMERICAL MODELLING OF THE MECHANICAL PROCESS OF PARTICLE DETACHMENT BY FINITE ELEMENT METHOD
This paper presents a numerical simulation technique for calculating the strain and the stress state at every point
of the surfaces, containing real surface topology and layered structure. Depending on the nature of deformation,
we can evaluate the actual stress and strain state either from the point of view of the fatigue failure or from the
point of view of the exhaustion of deformation capacity of the surfaces. Using the stress and strain components
calculated by the Finite Element Method at every nodal point of the surfaces, it is possible to predict the probable
surfaces degradation mechanism, i.e. to predict the probable mechanism of the
particle detachment under dry
sliding conditions, under consideration of the nominal load and to the required lifetime of the surface
Tribológiai jelenségek néhány szubmikroszkópikus vonatkozásának vizsgálata = Investigation of the submicroscopic of tribological phenomena
A kutatĂłmunka cĂ©lja a sĂşrlĂłdĂł felĂĽlet igen vĂ©kony rĂ©tegĂ©ben, az Ăşn. felĂĽletközeli rĂ©tegben a sĂşrlĂłdási igĂ©nybevĂ©tel hatására bekövetkezĹ‘ állandĂłsult, ill. tranziens szerkezeti változások vizsgálata volt. Ezeket a változásokat a tribolĂłgiai szakirodalom TTS-nek (Tribological Transformation of the Surface) nevezi. Vizsgálatainkhoz fĂ©mes (ötvözetlen acĂ©l, nagytisztaságĂş magnĂ©zium Ă©s titán) Ă©s nemfĂ©mes (szálerĹ‘sĂtĂ©sű karbon-karbon kompozit, polikristályos gyĂ©mánt Ă©s amorf karbon) sĂşrlĂłdĂł felĂĽletpárokat használtunk. A sĂşrlĂłdĂł felĂĽletek geometriája gömb-sĂkfelĂĽlet jellegű volt, mivel ennĂ©l az Ă©rintkezĂ©si tĂpusnál legjelentĹ‘sebb az Ă©rintkezĂ©si feszĂĽltsĂ©gi állapot hidrosztatikus komponensĂ©nek hatása. A sĂşrlĂłdásvizsgálatokat kiegĂ©szĂtettĂĽk járulĂ©kos hidrosztatikus nyomás alatt vĂ©gzett anyagvizsgálatokkal, amelynek eredmĂ©nyeibĹ‘l a sĂşrlĂłdásvizsgálat numerikus szimuláciĂłjához szĂĽksĂ©ges anyagtörvĂ©nyt határoztuk meg. A vizsgált felĂĽleteket 3D-topográfia, optikai- Ă©s elektronmikroszkĂłpia, elektron-diffrakciĂł, Raman-spektroszkĂłpia, Röntgen-difrakciĂł, atomi-erĹ‘-mikroszkĂłpia, mikro- Ă©s nanokemĂ©nysĂ©g mĂ©rĂ©sek eredmĂ©nyeivel jellemeztĂĽk. A prĂłbatestek elkĂ©szĂtĂ©sĂ©hez, valamint a vizsgálatok elvĂ©gzĂ©sĂ©hez, ill. az eredmĂ©nyek kiĂ©rtĂ©kelĂ©sĂ©hez Ă©s közzĂ©tĂ©telĂ©hez minden esetben felhasználtuk szĂ©leskörű nemzetközi kapcsolatainkat is, amelyek nagymĂ©rtĂ©kben hozzájárultak, hogy a megkezdett kutatĂłmunkát az OTKA támogatás befejezĂ©se után is folyatni tudjuk. | The goal of the research project was the investigation and analysis of some transient and permanent structural changes of the near surface layer due to a tribological load. These changes are referred to the tribological literature as TTS (Tribological Transformation of the Surface). Based on experience from previous research work, metallic (unalloyed steel, high purity magnesium and titanium) and non metallic (fiber reinforced carbon-carbon composite, amorphous carbon and polycrystalline diamond) friction surfaces pairs were chosen for the investigation. For the friction tests sphere-on-plate contact geometry of friction pairs was chosen, because for this type of contact the effect of the hydrostatic pressure component of the local stress state is important. The friction tests were completed by deformability tests under imposed hydrostatic pressure so providing the material law for the numerical simulations. Surfaces were characterized using the results of 3D surface topography, optical and electron microscopy, electron diffraction, Raman-spectroscopy, X-ray diffraction, atomic force microscopy, micro-, and nano-hardness measurements. For the manufacturing of the specimens, for the investigations and for the evaluation and publication of the results, we collaborated with our large international partnership, which allows us to continue the research after the termination of support from OTKA
A "stick-slip" jelentősége és tribológiai vizsgálatának lehetséges irányvonalai polimer gépelem alkalmazásokoz
A tribolĂłgiai vizsgálatok elterjedĂ©se, egyre szĂ©lesebb lehetĹ‘sĂ©geket nyit meg a kopási-sĂşrlĂłdási jelensĂ©gek vizsgálatával kapcsolatban. Ez kĂĽlönösen igaz az Ăşj szerkezeti anyagkĂ©nt tĂ©rt hĂłdĂtĂł műszaki műanyagok esetĂ©ben, ahol mĂ©g sok nyitott kĂ©rdĂ©s megoldása vár a kutatĂłkra. Ilyen rĂ©szterĂĽlet a stick-slip problĂ©mája, ami számos műszaki hiba okozĂłja világszerte. Munkánk cĂ©lja a stick-slip jelensĂ©g vizsgálati lehetĹ‘sĂ©geinek bemutatása kĂĽlönbözĹ‘ modell vizsgálati rendszerekben. A rendszerek közös jellemzĹ‘je az alternálĂł csĂşszĂłsĂşrlĂłdás, eltĂ©rĂ©seik mĂ©reteikben, a prĂłbatest geometriákban Ă©s az Ă©rintkezĂ©si viszonyokban nyilvánul meg