5,872 research outputs found
Recent Load Calibrations Experience with the YF-12 Airplane
The use of calibrated strain gages to measure wing loads on the YF-12A airplane is discussed as well as structural configurations relative to the thermal environment and resulting thermal stresses. A thermal calibration of the YF-12A is described to illustrate how contaminating thermal effects can be removed from loads equations. The relationship between ground load calibrations and flight measurements is examined for possible errors, and an analytical approach to accommodate such errors is presented
Waveguide photonic limiters based on topologically protected resonant modes
We propose a concept of chiral photonic limiters utilising topologically
protected localised midgap defect states in a photonic waveguide. The chiral
symmetry alleviates the effects of structural imperfections and guaranties a
high level of resonant transmission for low intensity radiation. At high
intensity, the light-induced absorption can suppress the localised modes, along
with the resonant transmission. In this case the entire photonic structure
becomes highly reflective within a broad frequency range, thus increasing
dramatically the damage threshold of the limiter. Here we demonstrate
experimentally the principle of operation of such photonic structures using a
waveguide consisting of coupled dielectric microwave resonators.Comment: 6 pages, 4 figure
Voices Count: Employing A Critical Narrative Research Bricolage For Insights Into Dyscalculia
This qualitative study involved interviewing adult participants who were identified, or who self identified as having dyscalculia (also known as a mathematical learning disorder), with the objective of obtaining depth of perspective on how this phenomenon is interpreted, responded to, and managed by these individuals and those around them. This study utilizes a theoretical and methodological framework known as bricolage (Kincheloe, 2005) which involves the synthesis of narrative, auto-ethnographic, critical, feminist, neuroscientific, and psychometric perspectives, to explicate the constitution and experience of dyscalculia. This study also explores epistemological privilege within the discipline of educational psychology, and draws on the work Billington (1996, 2013) who advocates for greater employment of critical approaches within educational psychology; particularly, drawing on the work of Foucault, to explicate how the privileging of certain modes of inquiry contributes to the marginalization of those under study. Findings suggest that cognitive approaches to understanding dyscalculia are neither in agreement, nor above scrutiny, and that social factors, co-morbid conditions and pedagogical approaches to mathematics instruction play a role in the emergence and remediation of dyscalculia. Ultimately, dyscalculia is explicated as a multidimensional phenomenon that raises important questions about how learning differences are approached and understood in educational research and practice
The use of a simplified structural model as an aid in the strain gage calibration of a complex wing
The use of a relatively simple structural model to characterize the load responses of strain gages located on various spars of a delta wing is examined. Strains measured during a laboratory load calibration of a wing structure are compared with calculations obtained from a simplified structural analysis model. Calculated and measured influence coefficient plots that show the shear, bending, and torsion characteristics of typical strain gage bridges are presented. Typical influence coefficient plots are shown for several load equations to illustrate the derivation of the equations from the component strain gage bridges. A relatively simple structural model was found to be effective in predicting the general nature of strain distributions and influence coefficient plots. The analytical processes are shown to be an aid in obtaining a good load calibration. The analytical processes cannot, however, be used in lieu of an actual load calibration of an aircraft wing
Preliminary Results of Aerodynamic Heating Studies on the X-15 Airplane
Aerodynamic heating analysis of X-15 aircraft in fligh
Computational Modeling of Hip Replacement Surgery: Total Hip Replacement vs. Hip Resurfacing
The motivation of the present work is the computational simulation of hip replacement surgery by means of a finite element approach based on open system thermodynamics. Its key feature is a non-constant material density, which is allowed to adapt with respect to changes in the mechanical loading environment. From a computational point of view, the density is treated as an internal variable. Its evolution is governed by a first order rate equation, the balance of mass, which is enhanced by an additional mass production term to account for growth. An implicit Euler backward scheme is suggested for its time discretization. The algorithmic determination of the material density based on a local Newton iteration is presented. To ensure quadratic convergence of the global Newton Raphson solution scheme, a consistent linearization of the discrete algorithmic equations is carried out. Finally, two alternative medical techniques in hip arthritis are compared, the conventional total hip replacement strategy and the more recent hip resurfacing technology. The result of the suggested remodeling algorithm is shown to agree remarkably well with clinically observed phenomena
Statistics of the electromagnetic response of a chaotic reverberation chamber
This article presents a study of the electromagnetic response of a chaotic
reverberation chamber (RC) in the presence of losses. By means of simulations
and of experiments, the fluctuations in the maxima of the field obtained in a
conventional mode-stirred RC are compared with those in a chaotic RC in the
neighborhood of the Lowest Useable Frequency (LUF). The present work
illustrates that the universal spectral and spatial statistical properties of
chaotic RCs allow to meet more adequately the criteria required by the Standard
IEC 61000-4-21 to perform tests of electromagnetic compatibility.Comment: 6 pages, 9 figure
- …