AlZn based Co and Ni catalysts for the partial oxidation of bioethanol - Influence of different synthesis procedures

The catalytic performance of Co and Ni catalysts on AlZn mixed oxide supports depends on the synthesis procedure used for their preparation. For this study CoAlZn and NiAlZn catalysts were prepared by conventional sol-gel synthesis of the mixed oxide and subsequent impregnation of the support with the transition metal (SG = sol gel method) as well as by a single-step method were a gel is formed based on salts of all components using citric acid as chelating agent (CM = citrate method). The structure and morphology of the catalysts were characterized by nitrogen sorption, XRD and TPR measurements. They showed high activity in the partial oxidation of ethanol at 600-750 °C, but their properties depend on the preparation method. The higher performance of the catalysts prepared by the citrate method, where the transition metal is incorporated into the crystal structure of the support during preparation, is based on a change in morphology and structure, resulting in more active sites exposed on the surface. Compared to the Co catalysts, Ni catalysts showed a higher performance. This might be due to the higher reducibility and the smaller Ni particles size, which allows a better interaction with the support in NiAlZn catalysts

AlZn based Co and Ni catalysts for the partial oxidation of bioethanol — influence of different synthesis procedures

The catalytic performance of Co and Ni catalysts on AlZn mixed oxide supports depends on the synthesis procedure used for their preparation. For this study CoAlZn and NiAlZn catalysts were prepared by conventional sol-gel synthesis of the mixed oxide and subsequent impregnation of the support with the transition metal (SG = sol gel method) as well as by a single-step method were a gel is formed based on salts of all components using citric acid as chelating agent (CM = citrate method). The structure and morphology of the catalysts were characterized by nitrogen sorption, XRD and TPR measurements. They showed high activity in the partial oxidation of ethanol at 600-750 °C, but their properties depend on the preparation method. The higher performance of the catalysts prepared by the citrate method, where the transition metal is incorporated into the crystal structure of the support during preparation, is based on a change in morphology and structure, resulting in more active sites exposed on the surface. Compared to the Co catalysts, Ni catalysts showed a higher performance. This might be due to the higher reducibility and the smaller Ni particles size, which allows a better interaction with the support in NiAlZn catalysts

Catalytic performance of CoAlZn and NiAlZn mixed oxides in hydrogen production by bio-ethanol partial oxidation

CoAlZn and NiAlZn mixed oxides were prepared by sol-gel method and tested in partial oxidation of bio-ethanol (POE). At lower temperatures, CoAlZn showed higher ethanol conversion and higher selectivity to H2 and CO than NiAlZn. At higher temperatures, ethanol conversion on both catalysts reached 100%, while selectivity (S) to H2 and CO became higher on NiAlZn. At 750 C, NiAlZn showed S(H2) of 95%, S(CO) of 90%, while for CoAlZn these values were 90% and 83% respectively. Both catalysts were resistant to coking, but the amount of carbon deposits was still lower on NiAlZn. During 50 h on-stream, ethanol conversion and selectivity to H2 and CO on NiAlZn remained unchanged demonstrating stable performance of the catalyst. The difference in catalytic behavior was ascribed to different reducibility and lattice oxygen mobility in the mixed oxides. TPR and DRIFT-monitored pyridine desorption tests revealed that in the respective materials, NiO particles were reduced easier than Co3O4 and NiAlZn had more mobile lattice oxygen with higher capacity to form vacancies than CoAlZn. Higher concentration of metallic Ni species coupled with more abundant mobile oxygen afforded correspondingly higher rates of C-H bond cleavage and carbon removal as CO on NiAlZn than on CoAlZn. Copyright © 2013, Hydrogen Energy Publications, LLC. Published by Elsevier Ltd. All rights reserved

Phase formation in mixed TiO2-ZrO2 oxides prepared by sol-gel method

Pure titania, zirconia, and mixed oxides (3\u201437 mol.% of ZrO2) are prepared using the sol-gel method and calcined at different temperatures. The calcined samples are characterized by Raman spectroscopy, X-ray powder diffraction, scanning electron microscopy, transmission electron microscopy, and nitrogen adsorption porosimetry. Measurements reveal a thermal stability of the titania anatase phase that slightly increases in the presence of 3\u201413 mol.% of zirconia. Practically, the titania anatase-rutile phase transformation is hindered during the temperature increase above 700 C. The mixed oxide with 37 mol.% of ZrO2 treated at 550 C shows a new single amorphous phase with a surface area of the nanoparticles double with respect to the other crystalline samples and the formed srilankite structure (at 700 C). The anatase phase is not observed in the sample containing 37 mol.% of ZrO2. The treatment at 700 C causes the formation of the srilankite (Ti0.63Zr0.37Ox) phase

H3PW12O40 supported on mesoporous MCM-41 and Al-MCM-41 materials: preparation and characterisation

MCM-41 and Al–MCM-41 has been synthesized using cetyl-trimethylammonium bromide (CTAB) surfactant as template and adding the silica precursor to aqueous solutions containing CTAB. The obtained solids were calcined at 600 C for 4 h. HPW heteropolyacid supported on the mesoporous were prepared using the incipient wetness method. The characterization of materials was performed by X-ray diffraction, Transmission Electron Microscopy, N2 adsorption, 29Si Cross Polarization– Magic Angle Spinning and 27Al MAS NMR. Results showed that the hexagonal structure is obtained in both cases. The Aluminium species are located inside an extraframework. The impregnation reduces the surface area of the mesoporous materials especially of the Al–MCM-41 suggesting a participation of aluminium during the impregnation. HPW is well dispersed in the mesoporous materials and is located inside the pores interacting with the silanol group of the pores wall. 27Al MAS NMR measurements have showed that the impregnation causes the removal of the non-framework aluminium

Mechanical treatment of TiO2 and ZrO2 oxide mixtures

The mixed ZrO2–TiO2 system (5–50 wt% of ZrO2) has been studied to investigate the influence of the mechanical treatment on its physicochemical properties depending on the composition, time of milling (5, 10 and 20 min, r.p.m. 82) and temperature (400, 550 and 700 C). Samples were characterized by Raman spectroscopy, X-ray powder diffraction, Scanning Electron Microscopy coupled with Energy Dispersion X-ray analyzer, High Resolution-Transmission Electron Microscopy and nitrogen adsorption porosimetry. Results show that srilankite (TiZrO4) phase has been produced. No influence of the milling time and temperature on the phase composition is observed. The presence of zirconia increases the thermal stability of anatase phase up to 700 C hindering the anatase— rutile phase transformation

Nanoparticles of AlTiZr mixed oxides as support of hydrodesulfurizaton catalysts: Synthesis and characterisation

TiAlZr mixed oxides, synthesized using sol–gel method, were characterized and used as supports of hydrodesulfurization catalysts (12 wt% Mo) prepared by impregnation either with molybdenum heteropolyacid H3PMo12O40 or its cobalt salt Co1.5PMo12O40. Structure, morphology and textural properties of oxides and catalysts were characterized using X-ray powder diffraction (XRD), Raman spectroscopy, Nitrogen adsorption porosimetry, TEM-EDS, temperature-programmed desorption (TPD) and temperature-programmed reduction (TPR) techniques. Activity of the catalytic systems was tested in thiophene hydrodesulfurization (HDS). No formation of a new oxide phase was revealed in the synthesized mixed materials. However the effect of separated oxides on the structure of ternary oxides was observed. Maximum in HDS activity of Mo containing samples was determined by optimum content of alumina in the mixed oxides. Incorporation of cobalt into the heteropolyacid increased the HDS activity about two times and masked the effect of the support composition

Synthesis, Characterization and Catalytic Activity of mesoporous Mn-MCM-41 materials

MCM-41 has been synthesized at two different pH using cetyl-trimethylammonium bromide (CTAB) surfactant as template and adding the silica precursor to aqueous solutions containing CTAB. The obtained solids were calcined at 600 ◦C for 4 h. Mn-MCM-41 powders with different Mn/Si molar ratios were prepared using the incipient wetness method, followed by calcination at 550 ◦C for 5 h. At the end of the impregnation process the powders colour changed from white to brown whose intensity depends on manganese quantity. The materials characterization was performed by X-ray diffraction, N2 adsorption, 29Si Cross Polarization–Magic Angle Spinning NMR, and X-ray Photoelectron Spectroscopy. The effects of the manganese quantity and of the structural characteristic of the MCM-41 support were studied. The catalytic activity of the prepared systems was evaluated in a complete n-hexane oxidation