25 research outputs found
The Insulation Vacuum Barrier for the Large Hadron Collider (LHC) Magnet Cryostats
The sectorisation of the insulation vacuum of the LHC magnet cryostats, housing the superconducting magnets, which operate in a 1.9 K superfluid helium bath, is achieved by means of vacuum barriers. Each vacuum barrier is a leak-tight austenitic stainless steel thin-wall structure, mainly composed of large diameter (between 0.6 m and 0.9 m) bellows and concentric corrugated cylinders. It is mounted in the Short Straight Section (SSS) [1], between the magnet helium enclosure and the vacuum vessel. This paper presents the design of the vacuum barrier, concentrating mostly on its expected thermal performance, to fulfil the tight LHC heat in-leak budgets. Pressure and leak test results, confirming the mechanical design of two prototypes manufactured in industry, and the preparation of one of these vacuum barriers for cryogenic testing in an SSS prototype, are also mentioned
First Measurement of the Damping Rate of High-n Toroidal Alfvén Eigenmodes in JET Tokamak Plasmas
Progress on the ITER upper launcher millimeter-wave design and testing
The aim of the ITER electron cyclotron heating and current drive upper launcher (UL) is to control magnetohydrodynamic activity in the plasma, in particular neoclassical tearing modes, requiring a narrow and peaked deposition of the radio-frequency (rf) power. The millimeter-wave (mm-wave) system of the UL is optimized to ensure that the eight rf beams are all focused to a small beam width at the resonance location. The present design uses two mitre bends per beam and a focusing mirror for each set of four beams, orientating each set onto a single steering mirror (SM) to inject it into the plasma. The SM is rotated using a frictionless and backlash free pneumo-mechanical system. A first prototype of the SM has been constructed to demonstrate the manufacturability and the actuation principle and to develop an adequate control strategy. A test program has been developed to ensure the integrity of the launcher from the pre-build-to-print design phase (research and development) up to the tests after maintenance. This paper presents a general overview of the system, a description of the progress in the mm-wave optical layout, low-power tests, alignment specifications of the mm-wave components, and SM capabilities to meet the ITER requirements
Design status of the ITER ECRH upper launcher mm-wave system
The purpose of the ITER electron cyclotron resonance heating (ECRH) upper launcher (UL), or antennae will be to provide localised current drive by accurately directing mm-wave beams up to 2MW, out of the four allocated upper port plugs, at chosen rational magnetic flux surfaces in order to stabilise neoclassical tearing modes (NTMs). This paper will present an overview of the UL, with emphasis on the mm-wave components. The mm-wave layout includes corrugated waveguide sections and a quasi-optical path with both focusing mirrors and plane steering mirrors. One of the essential components of the UL is the Steering Mechanism Assembly (SMA), providing variable poloidal injection angles fulfilling high deposition accuracy requirements at the plasma location. The Actuator principle and rotor bearings are frictionless and backlash free, avoiding tribological difficulties such as stickslip and seizure. The underlying working principle is the use of mechanically compliant structures. Validation and proof testing of the steering principle is achieved with an uncooled first prototype demonstrator. A second prototype is currently being manufactured, comprising the functionalities needed for the ITER compatible system such as water cooling and high power mm-wave compatibility. In order to perform the fatigue tests of the actuator bellows, a test facility has been built, under ITER-like vacuum and temperature working conditions. Results of the cyclic fatigue tests are compared to the various manufacturer standards and codes, combining stress and strain controlled material fatigue properties. (C) 2008 Elsevier B.V. All rights reserved
Progress on the ITER ECRH upper launcher steering mirror identification and control
The main objective of the ITER ECRH upper launcher (UL) is to control magnetohydrodynamic activity, in particular neoclassical tearing modes (NTMs), by driving several MW of EC current near the q = 1, 3/2, 2 flux surfaces, where NTMs are expected to occur. The steering of the EC power is done by the steering mechanism assembly (SMA) that comprises a reflecting mirror and a frictionless and backlash free pneumo-mechanical system actuated with pressurised helium gas. The control requirements for this component in terms of steering accuracy and speed are reviewed. With respect to these requirements, the performance of the first SMA prototype is assessed in a mock up of the UL pneumatic configuration. The expected design characteristics of the SMA have been verified and an overall satisfactory performance has been assessed. Furthermore, the main challenges for the future work, such as the pressure and angular position control, have been identified