98 research outputs found
An efficient CDMA system based on Reed Solomon Code (RS code)
Accurate Error control is a necessary constraint for the design of Celluar Code Division Multiple Access ( CDMA ) systems. The Block codes can correct twice as many erasures as errors , the coded performance can be improved . In this paper , We propose ‘ An efficient Error correcting coding in CDMA systems. The system performance is improved using FEC based on Walsh code and PN sequence. The power consumption of transrecevier is the requirement for low power communication systems such as wireless personal area networks , low data rate networks. The FEC schemes are selected based on its performance. To improve communication robustness , the correcting capabilities shall be seen to determine the transmit power. The probability of incorrect Decoding can be significantly improved using RS codes.
Structural and electronic properties of Pb1-xCdxTe and Pb1-xMnxTe ternary alloys
A systematic theoretical study of two PbTe-based ternary alloys, Pb1-xCdxTe
and Pb1-xMnxTe, is reported. First, using ab initio methods we study the
stability of the crystal structure of CdTe - PbTe solid solutions, to predict
the composition for which rock-salt structure of PbTe changes into zinc-blende
structure of CdTe. The dependence of the lattice parameter on Cd (Mn) content x
in the mixed crystals is studied by the same methods. The obtained decrease of
the lattice constant with x agrees with what is observed in both alloys. The
band structures of PbTe-based ternary compounds are calculated within a
tight-binding approach. To describe correctly the constituent materials new
tight-binding parameterizations for PbTe and MnTe bulk crystals as well as a
tight-binding description of rock-salt CdTe are proposed. For both studied
ternary alloys, the calculated band gap in the L point increases with x, in
qualitative agreement with photoluminescence measurements in the infrared. The
results show also that in p-type Pb1-xCdxTe and Pb1-xMnxTe mixed crystals an
enhancement of thermoelectrical power can be expected.Comment: 10 pages, 13 figures, submitted to Physical Review
Recommended from our members
Degradation and Capacitance-Voltage Hysteresis in CdTe Devices: Preprint
CdS/CdTe cells on CTO/ZTO TCO show greater intial performance than SnO2-gased substrates due to superior optical and electrical properties of the oxide layers and more rigorous CdCl2 processing. Performance unfiormity was a problem
Recommended from our members
Determination of Cu Concentrations in CdTe/CdS Devices by High Mass Resolution Secondary Ion Mass Spectrometry
We have used secondary ion mass spectrometry (SIMS) to quantitatively determine the concentration of Cu in CdTe/CdS devices. Empirical standards were fabricated by ion implantation of Cu into single-crystal and polycrystalline CdTe and single-crystal CdS
Recommended from our members
Cross-Section AFM and EFM Examination of Thin-Film Solar Cells
We demonstrated the feasibility of analyzing cross sections of thin-film CdTe/CdS and CIGS/CdS solar cells using atomic force microscopy (AFM)
Recommended from our members
Recrystallization of PVD CdTe Thin Films Induced by CdCl2 Treatment -- A Comparison Between Vapor and Solution Processes: Preprint
This paper describes the large concentration of 60..deg.. twin boundaries that was observed in every CdTe film analyzed in this work, even after recrystallization and grain growth, confirming the low energy of these interfaces
Recommended from our members
Cross-Sectional Conductive Atomic Force Microscopy of CdTe/CdS Solar Cells: Effects of Etching and Back-Contact Processes; Preprint
We investigated the effects of the etching processes using bromine and nitric-phosphoric acid solutions, as well as of Cu, in the bulk electrical conductivity of CdTe/CdS solar cells using conductive atomic force microscopy (C-AFM). Although the etching process can create a conductive layer on the surface of the CdTe, the layer is very shallow. In contrast, the addition of a thin layer of Cu to the surface creates a conductive layer inside the CdTe that is not uniform in depth, is concentrated at grains boundaries, and may short circuit the device if the CdTe is too thin. The etching process facilitates the Cu diffusion and results in thicker conductive layers. The existence of this inhomogeneous conductive layer directly affects the current transport and is probably the reason for needing thick CdTe in these devices
Effects of deposition time and post-deposition annealing on the physical and chemical properties of electrodeposited CdS thin films for solar cell application
CdS thin films were cathodically electrodeposited by means of a two-electrode deposition system
for different durations. The films were characterised for their structural, optical, morphological
and compositional properties using x-ray diffraction (XRD), spectrophotometry, scanning
electron microscopy (SEM) and energy dispersive x-ray (EDX) respectively. The results obtained
show that the physical and chemical properties of these films are significantly influenced by the
deposition time and post-deposition annealing. This influence manifests more in the as-deposited
materials than in the annealed ones. XRD results show that the crystallite sizes of the different
films are in the range (9.4 – 65.8) nm and (16.4 – 66.0) nm in the as-deposited and annealed
forms respectively. Optical measurements show that the absorption coefficients are in the range
(2.7×104 – 6.7×104) cm-1 and (4.3×104 – 7.2×104) cm-1 respectively for as-deposited and annealed
films. The refractive index is in the range (2.40 – 2.60) for as-deposited films and come to the
value of 2.37 after annealing. The extinction coefficient varies in the range (0.1 – 0.3) in asdeposited
films and becomes 0.1 in annealed films. The estimated energy bandgap of the films is
in the range (2.48 – 2.50) eV for as-deposited films and becomes 2.42 eV for all annealed films.
EDX results show that all the films are S-rich in chemical composition with fairly uniform Cd/S
ratio after annealing. The results show that annealing improves the qualities of the films and
deposition time can be used to control the film thickness.
Keywords: Electrodeposition; two-electrode system; CdS; annealing; deposition time; thin-film
Recommended from our members
Advances in CdTe R&D at NREL
This paper summarizes the following R&D accomplishments at National Renewable Energy Laboratory (NREL): (1) Developed several novel materials and world-record high-efficiency CdTe solar cell, (2) Developed "one heat-up step" manufacturing processes, and (3) Demonstrated 13.9% transparent CdTe cell and 15.3% CdTe/CIS polycrystalline tandem solar cell. Cadmium telluride has been well recognized as a promising photovoltaic material for thin-film solar cells because of its near-optimum bandgap of ~1.5 eV and its high absorption coefficient. Impressive results have been achieved in the past few years for polycrystalline CdTe thin-film solar cells at NREL. In this paper, we summarize some recent R&D activities at NREL
- …