Transonic Aerodynamic Characteristics of a 45 deg Swept Wing Fuselage Model with a Finned and Unfinned Body Pylon Mounted Beneath the Fuselage or Wing, Including Measurements of Body Loads

An investigation of a model of a standard size body in combination with a representative 45 deg swept-wing-fuselage model has been conducted in the Langley 8-foot transonic pressure tunnel over a Mach number range from 0.80 to 1.43. The body, with a fineness ratio of 8.5, was tested with and without fins, and was pylon-mounted beneath the fuselage or wing. Force measurements were obtained on the wing-fuselage model with and without the body, for an angle-of-attack range from -2 deg to approximately 12 deg and an angle-of-sideslip range from -8 deg to 8 deg. In addition, body loads were measured over the same angle-of-attack and angle-of-sideslip range. The Reynolds number for the investigation, based on the wing mean aerodynamic chord, varied from 1.85 x 10(exp 6) to 2.85 x 10(exp 6). The addition of the body beneath the fuselage or the wing increased the drag coefficient of the complete model over the Mach number range tested. On the basis of the drag increase per body, the under-fuselage position was the more favorable. Furthermore, the bodies tended to increase the lateral stability of the complete model. The variation of body loads with angle of attack for the unfinned bodies was generally small and linear over the Mach number range tested with the addition of fins causing large increases in the rates of change of normal-force coefficient and nose-down pitching-moment coefficient. The variation of body side-force coefficient with sideslip for the unfinned body beneath the fuselage was at least twice as large as the variation of this load for the unfinned body beneath the wing. The addition of fins to the body beneath either the fuselage or the wing approximately doubled the rate of change of body side-force coefficient with sideslip. Furthermore, the variation of body side-force coefficient with sideslip for the body beneath the wing was at least twice as large as the variation of this load with angle of attack

Transonic Aerodynamic Characteristics of a Model of a Proposed Six-Engine Hull-Type Seaplane Designed for Supersonic Flight

Force tests of a model of a proposed six-engine hull-type seaplane were performed in the Langley 8-foot transonic pressure tunnel. The results of these tests have indicated that the model had a subsonic zero-lift drag coefficient of 0.0240 with the highest zero-lift drag coefficient slightly greater than twice the subsonic drag level. Pitchup tendencies were noted for subsonic Mach numbers at relatively high lift coefficients. Wing leading-edge droop increased the maximum lift-drag ratio approximately 8 percent at a Mach number of 0.80 but this effect was negligible at a Mach number of 0.90 and above. The configuration exhibited stable lateral characteristics over the test Mach number range

NACA Research Memorandums

Report presenting force tests of a 0.10-scale model of the Douglas A4D-1 airplane in the 8-foot transonic pressure tunnel to investigate the static longitudinal characteristics of wing and fuselage modifications and the static lateral characteristics of the basic model. Tests were conducted over a range of Mach numbers and angles of attack

NACA Research Memorandums

From Introduction: "Results from the tests in the Langley 4- by 4-foot supersonic pressure tunnel at Mach numbers of 1.61 and 2.01 are presented in reference 1. Reported herein are results obtained from the tests in the Langley 8-foot transonic tunnel of the model with no control deflections at Mach numbers 0.6 to 1.12 for angles of attack up to 34^

NACA Research Memorandums

Memorandum presenting the buffet characteristics of a scale model of an attack airplane over a range of Mach numbers. The wing had a modified delta plan form with an NACA 0008 airfoil section at the root and an NACA 0005 airfoil section at the tip, a leading-edge sweep of 41.11 degrees, an aspect ratio of 2.91, and a taper ratio of 0.226. Results regarding the frequency spectrum of bending moment, effect of density on root-mean-square bending moment, system damping coefficients, and buffet input force are provided

NACA Research Memorandum

Report discussing testing of a model of the Douglas A4D-1 to investigate the static longitudinal characteristics of wing and fuselage modifications and the static lateral characteristics of the basic model

NACA Research Memorandums

Report presenting an investigation of the buffet characteristics of a model of an attack airplane at a variety of Mach numbers. The wing had a modified delta plan form with two NACA airfoils, a leading-edge sweep of 41.11 degrees, an aspect ratio of 2.91, and a taper ratio of 0.226. Results regarding frequency spectrum of bending moment, effect of density on root-mean-square bending moment, system damping coefficients, and buffet input force are provided