The low-angle boundaries misorientation and lattice parameter changes in the root of single-crystalline CMSX-4 superalloy blades

The relationship between the angles of misorientation of macroscopic low-angle boundaries (LABs) and changes in the lattice parameter of the 0-phase around the LABs in the root of singlecrystalline (SX) turbine blades made of CMSX-4 superalloy were studied. The blades with an axial orientation of the [001] type were solidified using an industrial Bridgman furnace with a 3 mm/min withdrawal rate. X-ray diffraction topography, the EFG W-scan X-ray diffraction method, scanning electron microscopy, and Laue diffraction were used to study the thin lamellar samples with a thickness of 0.5 mm and orientation of the surface perpendicular to the [001] direction. It is found that in the areas with a width of a few millimetres around LABs, decreases in the lattice parameter of the 0-phase occur. These lattice parameter changes are related to the internal stresses of the 0-phase caused by local changes in the concentration of alloying elements and/or to the dendrite bending near the LABs. X-ray topography used on two surfaces of thin lamellar samples coupled with the lattice parameter measurements of the 0-phase near the LAB allows separating the misorientation component of LAB diffraction contrast from the component and visualising the internal stresses of the 0-phase

Heterogeneity of the dendrite array created in the root of cored SX turbine blades during initial stage of crystallization

The roots of cored single-crystalline turbine blades made of a nickel-based CMSX-4 superalloy were studied. The casts were solidified by the vertical Bridgman method in an industrial ALD furnace using the spiral selector and selector continuer situated asymmetrically in the blade root transverse section. Scanning electron microscopy, the Laue diffraction and X-ray diffraction topography were used to visualize the dendrite array and the local crystal misorientation of the roots. It has been stated that heterogeneity of the dendrite array and creation of low-angle boundaries (LABs) are mostly related to the lateral dendrite branching and rapid growth of the secondary and tertiary dendrites near the surface of the continuer–root connection. These processes have an unsteady character. Additionally, the influence of the mould walls on the dendrite array heterogeneity was studied. The processes of the lateral growth of the secondary dendrites and competitive longitudinal growth of the tertiary dendrites are discussed and a method of reducing the heterogeneity of the root dendrite array is proposed

The effect of withdrawal rate on crystal structure perfection, microstructure and creep resistance of single crystal castings made of CMSX-4 nickel-based superalloy

This study focuses on the evaluation of the crystal structure perfection in the single crystal made of CMSX-4 nickel superalloy and its effect on creep resistance. Single crystal castings were manufactured by directional solidification process at the withdrawal rate of 1, 3, 5 and 7 mm/min. Light (LM) and electron (SEM, TEM) microscopy, X-ray diffraction and Mossbauer spectroscopy were used for evaluation of the microstructure and crystal structure perfection. Castings were also subjected to creep tests. The best creep resistance was obtained for the casting manufactured at the withdrawal rate of 3 mm/min, characterized by the highest crystal structure perfection compared to the other castings examined

Determination of crystal orientation by Ω-scan method in nickel-based single-crystal turbine blades

The article presents an assessment of the crystal perfection of single-crystal turbine blades based on the crystal orientation and lattice parameter distribution on their surface. Crystal orientation analysis was conducted by the X-ray diffraction method Ω-scan and the X-ray diffractometer provided by the EFG Company. The Ω-scan method was successfully used for evaluation of the crystal orientation and lattice parameters in semiconductors. A description of the Ω-scan method and an example of measurement of crystal orientation compared to the Laue and EBSD methods are presented.This work was supported by the National Science Centre Poland (NCN) under Grant No. Preludium-UMO-2016/21/N/ST8/00240

Ból i cierpienie

Publikacja recenzowana / Peer-reviewed publicationZE WSTĘPU: W tym roku oddajemy do rąk Czytelników szczególnie uroczysty zeszyt cyklicznego wydawnictwa Krakowskiej Szkoły Wyższej „Acta Academiae Modrevianae”, na łamach którego zamieszczamy referaty wygłoszone na jubileuszowej sesji nt. „Ból i cierpienie” w 2007 roku

Preliminary design of axial-flow compressor to gas turbine

praca magistersk

Investigation of the effect of solidification velocity on the quality of single crystal turbine blades

The occurrence of high temperatures in combustion chambers of jet engines and gas turbines has led to the demand for new technologies and new materials for the manufacture of one of the most critical elements of these systems - the turbine blades. These elements have to withstand extreme temperatures for extended periods without loss of mechanical strength, conditions under which many alloys fail. Such failure is ascribed to the combination of high temperatures and high centrifugal forces, resulting in creep. This is especially prevalent in multi-crystalline structures in which grain boundaries present weaknesses in the structure. High temperature resistant alloys formed as single crystal (SX) structures offer the necessary material properties for safe performance under such extreme conditions. Modelling and simulation techniques were first used to study the directional solidification (DS) of crystal structures during vacuum investment casting. These models allowed the study of the dendritic growth rate, the formation of new grains ahead of the solid/liquid interface and the morphology of the dendritic microstructure. These studies indicated the opportunity to optimise the velocity of the solidification front (solidification rate) for single crystal structures. The aim of this study was therefore to investigate the effect of the solidification rate on the quality of SX castings. The investigations were carried out for nickel-based superalloy CMSX-4 turbine blade casts and rods using the Bridgman process for vacuum investment casting

Application of Inner Radiation Baffles in the Bridgman Process for Flattening the Temperature Profile and Controlling the Columnar Grain Structure of Directionally Solidified Ni-Based Superalloys

The technique of flattening the temperature profile and controlling the formation of both the dendritic microstructure and grain structure in the directional solidification of nickel-based superalloy casting, using the novel inner radiation baffles (IRBs) in the Bridgman process, is presented in this paper. These baffles matched to the shape of mold and were placed horizontally along its height at various distances from the casting base. The plate castings of CMSX-4 superalloy were fabricated without and with the use of IRBs, withdrawing the mold at the rate of 6 mm/min from the heating to the cooling area of the industrial Bridgman furnace. Thermal analysis of the directional solidification of castings was carried out using the ProCAST software for a process where the various designs of the radiation baffle were applied. The results of the solidification conditions, the shape of liquidus and solidus isotherms, and grain structure obtained for the IRBs were compared with those reached for the standard ring-shaped (AERB) or perfectly adjusted (PARB) radiation baffles. The use of IRB resulted in flattening of the temperature distribution and decrease of the curvature of liquidus and solidus isotherms, as well as an increase of temperature gradient and cooling rate, compared with the process where AERB was only used. Consequently, primary dendrite arm spacing (PDAS) reached similar values across the width of casting and equaled to approximately 370 μm, reducing its average value by 26%, compared with the standard process. The change in predicted axial temperature gradient in casting was not found when thermophysical properties of molybdenum IRBs were used. The increase in graphite IRBs number in mold from seven to 14 caused the reduction of inhomogeneity of axial temperature gradient along the casting height