40 research outputs found
Recommended from our members
Localization of Volcanic Activity: Topographic Effects on Dike Propagation, Eruption and COnduit Formation
Magma flow in a dike rising in a crack whose strike runs from a highland or a ridge to an adjacent lowland has been modeled to determine the effect of topography on the flow. It is found that there is a distinct tendency for the flow to be diverted away from the highland end of the strike toward the lowland. Separation of the geometric effect of the topography from its effect on lateral confining stresses on the crack indicates that both contribute to the effect but that the effect of stress is less important. Although this analysis explains a tendency for volcanic eruptions to occur in low lands, it does not preclude eruptions on highlands. The particular configuration modeled mimics topography around the proposed nuclear waste repository at Yucca Mountain, Nevada, so that the results may indicate some reduction in the volcanic hazard to the site
Recommended from our members
CONDITIONS LEADING TO SUDDEN RELEASE OF MAGMA PRESSURE
Buildup of magmatic pressures in a volcanic system can arise from a variety of mechanisms. Numerical models of the response of volcanic structures to buildup of pressures in magma in dikes and conduits provide estimates of the pressures needed to reopen blocked volcanic vents. They also can bound the magnitude of sudden pressure drops in a dike or conduit due to such reopening. Three scenarios are considered: a dike that is sheared off by covolcanic normal faulting, a scoria cone over a conduit that is blocked by in-falling scoria and some length of solidified magma, and a lava flow whose feed has partially solidified due to an interruption of magma supply from below. For faulting, it is found that magma would be able to follow the fault to a new surface eruption. A small increase in magma pressure over that needed to maintain flow prior to faulting is required to open the new path, and the magma pressure needed to maintain flow is lower but still greater than for the original dike. The magma pressure needed to overcome the other types of blockages depends on the details of the blockage. For example, for a scoria cone, it depends on the depth of the slumped scoria and on the depth to which the magma has solidified in the conduit. In general, failure of the blockage is expected to occur by radial hydrofracture just below the blocked length of conduit at magma pressures of 10 MPa or less, resulting in radial dikes. However, this conclusion is based on the assumption that the fluid magma has direct access to the rock surrounding the conduit. If, on the other hand, there is a zone of solidified basalt, still hot enough to deform plastically, surrounding the molten magma in the conduit, this could prevent breakout of a hydrofracture and allow higher pressures to build up. In such cases, pressures could build high enough to deform the overlying strata (scoria cone or lava flow). Models of such deformations suggest the possibility of more violent eruptions resulting from sudden shear failure of a scoria cone with material accelerations near 100 m/s{sup 2}
Recommended from our members
DEFORMATION OF SCORIA CONE BY CONDUIT PRESSURIZATION
A simplified mechanical model is used to simulate the deformation of a scoria cone due to pressurization of magma in a feeder conduit. The scoria cone is modeled as consisting of a cone of stabilized scoria with an axial region of loose scoria (height h{sub 1}), all overlying a vertically oriented cylindrical conduit intruded into rhyolite tuff country rock. For our analyses, the conduit is filled with basalt magma, usually with the upper length (h{sub 2}) solidified. The style of deformation of the cone depends on both h{sub 1} and h{sub 2}. If magma is prevented from hydrofracturing out of the conduit (as, for example, might be the case if the magma is surrounded by a solidified, but plastically deformable layer acting as a gasket backed up by the brittle country rock) pressures in the magma can build to 10s of MPa. When h{sub 1} is 100 m, not unusual for a small isolated basaltic cinder cone, the magma pressure needed to destabilize the cone when molten magma extends all the way to the original ground surface (h{sub 2} = 0) is only about one-third of the pressure when the upper part of the conduit is solidified (h{sub 2} = 25m). In the former case, almost the entire upper third of the cone is at failure in tension when the configuration becomes unstable. In the latter case, small portions of the surface of the cone are failing in tension when instability occurs, but a large volume in the central core of the cone is failing in shear or compressions. These results may provide insight into the status of volcanic plumbing, either past or present, beneath scoria cones. Field observations at the Lathrop Wells volcano in southern Nevada identify structures at the outer edge just below the crater rim that appear to be inward-dipping listric normal faults. This may indicate that, near the end of its active stage, the cone was close to failing in this fashion. A companion paper suggests that such a failure could have been quite energetic had it occurred
Recommended from our members
Mechanical defradation of Emplacement Drifts at Yucca Mountain- A Modeling Case Study. Part I: Nonlithophysal Rock
This paper outlines rock mechanics investigations associated with mechanical degradation of planned emplacement drifts at Yucca Mountain, which is the designated site for the proposed U.S. high-level nuclear waste repository. The factors leading to drift degradation include stresses from the overburden, stresses induced by the heat released from the emplaced waste, stresses due to seismically related ground motions, and time-dependent strength degradation. The welded tuff emplacement horizon consists of two groups of rock with distinct engineering properties: nonlithophysal units and lithophysal units, based on the relative proportion of lithophysal cavities. The term 'lithophysal' refers to hollow, bubble like cavities in volcanic rock that are surrounded by a porous rim formed by fine-grained alkali feldspar, quartz, and other minerals. Lithophysae are typically a few centimeters to a few decimeters in diameter. Part I of the paper concentrates on the generally hard, strong, and fractured nonlithophysal rock. The degradation behavior of the tunnels in the nonlithophysal rock is controlled by the occurrence of keyblocks. A statistically equivalent fracture model was generated based on extensive underground fracture mapping data from the Exploratory Studies Facility at Yucca Mountain. Three-dimensional distinct block analyses, generated with the fracture patterns randomly selected from the fracture model, were developed with the consideration of in situ, thermal, and seismic loads. In this study, field data, laboratory data, and numerical analyses are well integrated to provide a solution for the unique problem of modeling drift degradation
Numerical ModelâSoftware for Predicting Rock Formation FailureâTime Using Fracture Mechanics
Realâtime integrated drilling is an important practice for the upstream petroleum industry. Traditional
preâdrill models, tend to offset the data gathered from the field since information obtained prior to
spudding and drilling of new wells often become obsolete due to the changes in geology and geomechanics
of reservoirârocks or formations. Estimating the complicated nonâlinear failureâtime of a rock
formation is a difficult but important task that helps to mitigate the effects of rock failure when drilling
and producing wells from the subsurface. In this study, parameters that have the strongest impact on
rock failure were used to develop a numerical and computational model for evaluating wellbore
instability in terms of collapse, fracture, rock strength and failureâtime. This approach presents drilling
and well engineers with a better understanding of the fracture mechanics and rock strength failureprediction
procedure required to reduce stability problems by forecasting the rock/formation failuretime.
The computational technique built into the software, uses the stress distribution around a rock
formation as well as the rockâs responses to induced stress as a means of analyzing the failure time of
the rock. The results from simulation show that the applied stress has the most significant influence on
the failureâtime of the rock. The software also shows that the failureâtime varied over several orders of
magnitude for varying stressâloads. Thus, this will help drilling engineers avoid wellbore failure by
adjusting the stress concentration properly through altering the mud pressure and well orientation with
respect to inâsitu stresses. As observed from the simulation results for the failure time analysis, the
trend shows that the time dependent strength failure is not just a function of the applied stress.
Because, at applied stress of 6000â6050 psi there was time dependent failure whereas, at higher
applied stress of 6350â6400 psi there was no time dependent strength failure
The role of rock joint frictional strength in the containment of fracture propagation
The fracturing phenomenon within the reservoir environment is a complex process that is controlled by several factors and may occur either naturally or by artificial drivers. Even when deliberately induced, the fracturing behaviour is greatly influenced by the subsurface architecture and existing features. The presence of discontinuities such as joints, artificial and naturally occurring faults and interfaces between rock layers and microfractures plays an important role in the fracturing process and has been known to significantly alter the course of fracture growth. In this paper, an important property (joint friction) that governs the shear behaviour of discontinuities is considered. The applied numerical procedure entails the implementation of the discrete element method to enable a more dynamic monitoring of the fracturing process, where the joint frictional property is considered in isolation. Whereas fracture propagation is constrained by joints of low frictional resistance, in non-frictional joints, the unrestricted sliding of the joint plane increases the tendency for reinitiation and proliferation of fractures at other locations. The ability of a frictional joint to suppress fracture growth decreases as the frictional resistance increases; however, this phenomenon exacerbates the influence of other factors including in situ stresses and overburden conditions. The effect of the joint frictional property is not limited to the strength of rock formations; it also impacts on fracturing processes, which could be particularly evident in jointed rock masses or formations with prominent faults and/or discontinuities
Numerical Simulation of Simultaneous Growth of Multiple Interacting Hydraulic Fractures from Horizontal Wells
Mechanical Degradation of Emplacement Drifts at Yucca Mountain-A Modeling Case Study-Part I: Nonlithophysal Rock
This paper outlines rock mechanics investigations associated with mechanical degradation of planned emplacement drifts at Yucca Mountain, which is the designated site for the proposed US high-level nuclear waste repository. The factors leading to drift degradation include stresses from the overburden, stresses induced by the heat released from the emplaced waste, stresses due to seismically related ground motions, and time-dependent strength degradation. The welded tuff emplacement horizon consists of two groups of rock with distinct engineering properties: nonlithophysal units and lithophysal units, based on the relative proportion of lithophysal cavities. The term âlithophysalâ refers to hollow, bubble like cavities in volcanic rock that are surrounded by a porous rim formed by fine-grained alkali feldspar, quartz, and other minerals. Lithophysae are typically a few centimeters to a few decimeters in diameter. Part I of the paper concentrates on the generally hard, strong, and fractured nonlithophysal rock. The degradation behavior of the tunnels in the nonlithophysal rock is controlled by the occurrence of keyblocks. A statistically equivalent fracture model was generated based on extensive underground fracture mapping data from the Exploratory Studies Facility at Yucca Mountain. Three-dimensional distinct block analyses, generated with the fracture patterns randomly selected from the fracture model, were developed with the consideration of in situ, thermal, and seismic loads. In this study, field data, laboratory data, and numerical analyses are well integrated to provide a solution for the unique problem of modeling drift degradation
Recommended from our members