22,188 research outputs found
EBIC/TEM investigations of process-induced defects in EFG silicon ribbon
Electron bombardment induced conductivity and scanning transmission electron microscopy observations on unprocessed and processed edge-defined film-fed growth ribbon show that the phosphorus diffused junction depth is not uniform, and that a variety of chemical impurities precipitate out during processing. Two kinds of precipitates are found (1) 10 nm or less in size, located at the dislocation nodes in sub-boundary like dislocation arrangements formed during processing and (2) large precipitates, the chemical composition of which has been partially identified. These large precipitates emit dense dislocations tangles into the adjacent crystal volume
Artificial meteor ablation studies: Olivine
Artificial meteor ablation was performed on a Mg-rich olivine sample using an arc-heated plasma of ionized air. Experimental conditions simulated a meteor traveling about 12 km/sec at an altitude of 70 km. The mineral content of the original olivine sample was 98% olivine (including traces of olivine alteration products) and 2% chromite. Forsterite content of the original olivine was Fo-89. After ablation, the forsterite content had increased to Fo-94 in the recrystallized olivine. In addition, lamella-like intergrowths of magnetite were prevalent constituents. Wherever magnetite occurred, there was an increase in Mg and a corresponding decrease in Fe for the recrystallized olivine. The Allende fusion crust consisted of a recrystallized olivine, which was more Mg-rich and Fe-deficient than the original meteorite's olivine, and abundant magnetite grains. Although troilite and pentlandite were the common opaque mineral constituents in this meteorite, magnetite was the principal opaque mineral found in the fusion crust
The Monetary Transmission Mechanism in The United Kingdom: Pass-Through & Policy Ru
A number of recent papers have used policy simulations from small empirical macro models to assess the efficacy of inflation-forecast targeting. The macro models used to undertake the simulations differ significantly with the assumed degree of openness, an important factor for the analysis. However, the open economy models typically approach the pass-through from exchange rate to import prices and ultimately retail prices in a stylized manner, assuming full and instantaneous pass-through. This paper modifies the open economy macro model presented in Batini and Haldane (1999) to accommodate a variety of pass-through representations, considering time and state-(cycle)-dependent pass-through rules. While the modelâs dynamics are affected, the main result of Batini and Haldane â that targeting an inflation forecast dominates targeting current inflation â is robust to the assumed rate of pass-through.
Processed-induced defects in EFG ribbons
The defect structure of processed edge defined film-fed growth (EFG) silicon ribbons was studied using a variety of electron microscopic techniques. Comparison between the present results and previous studies on as-grown ribbons has shown that solar cell processing introduces additional defects into the ribbons. The creation of point defects during high temperature phosphorus diffusion induces dislocation climb, resulting in the formation of dislocation helices in the diffused layer
Ultrasonic wave propagation in heterogenous media
The non-destructive testing of austenitic steel welds using ultrasound is of vital importance for assessing safety critical structures such as those found in the nuclear industry. The internal geometry of these welds is heterogeneous and highly scattering and this makes it dicult to detect and characterise any defects within them. To help overcome these diculties the use of ultrasound transducer arrays and the associated Full Matrix Capture is becoming more widespread. There is a need therefore to develop post-processing algorithms that best utilise the data from such devices. This paper considers the use of a time-frequency domain method known as the Decomposition of the Time Reversal Operator (DORT) method. To develop this method and to demonstrate its ecacy in tackling this problem a series of simulated data sets are used. The simulated data is generated using a finite element method (PZFLEX) with the heterogeneous internal microstructure of the weld being given by previous Electron Backscatter Diraction measurements. A range of artificial flaws are then inserted into this geometry. By varying the flaw size and type a comparison is conducted between the DORT method and the Total Focusing Method (TFM) and their relative ability to perform flaw detection assessed. Importantly, however, the DORT method relies on a Singular Value Decomposition in time and frequency space and this spectral information contains information about the flaw size and shape
Development of an advanced microelectronic connection welding system Final report
Development of microelectronic connection welding system using infrared feedback contro
Investigation of thermal fatigue in fiber composite materials
Graphite-epoxy laminates were thermally cycled to determine the effects of thermal cycles on tensile properties and thermal expansion coefficients of the laminates. Three 12-ply laminate configurations were subjected to up to 5,000 thermal cycles. The cumulative effect of the thermal cycles was determined by destructive inspection (electron micrographs and tensile tests) of samples after progressively larger numbers of cycles. After thermal cycling, the materials' tensile strengths, moduli, and thermal expansion coefficients were significantly lower than for the materials as fabricated. Most of the degradation of properties occurred after only a few cycles. The property degradation was attributed primarily to the progressive development of matrix cracks whose locations depended upon the layup orientation of the laminate
Detection of SiO emission from a massive dense cold core
We report the detection of the SiO (J = 2 - 1) transition from the massive
cold dense core G333.125-0.562. The core remains undetected at wavelengths
shorter than 70 micron and has compact 1.2 mm dust continuum. The SiO emission
is localised to the core. The observations are part of a continuing
multi-molecular line survey of the giant molecular cloud G333. Other detected
molecules in the core include 13CO, C18O, CS, HCO+, HCN, HNC, CH3OH, N2H+, SO,
HC3N, NH3, and some of their isotopes. In addition, from NH3 (1,1) and (2,2)
inversion lines, we obtain a temperature of 13 K. From fitting to the spectral
energy distribution we obtain a colour temperature of 18 K and a gas mass of 2
x 10^3 solar mass. We have also detected a 22 GHz water maser in the core,
together with methanol maser emission, suggesting the core will host massive
star formation. We hypothesise that the SiO emission arises from shocks
associated with an outflow in the cold core.Comment: 6 pages, 4 figures, 1 table, to be published in MNRA
The structure of 110 tilt boundaries in large area solar silicon
The models of Hornstra and their connection to the repeating group description of grain boundaries (7-10) are discussed. A model for the Sigma = 27 boundary containing a zig-zag arrangement of dislocations is constructed and it is shown that zig-zag models can account for the contrast features observed in high resolution transmission electron micrographs of second and third order twin boundaries in silicon. The boundaries discussed are symmetric with a 110 tilt axis and a (110) boundary plane in the median lattice (the median plane). The median lattice is identical in structure and halfway in orientation between the crystal lattices either side of the boundary
- âŠ