Confocal Ellipsoidal Reflector System for a Mechanically Scanned Active Terahertz Imager

We present the design of a reflector system that can rapidly scan and refocus a terahertz beam for high-resolution standoff imaging applications. The proposed optical system utilizes a confocal Gregorian geometry with a small mechanical rotating mirror and an axial displacement of the feed. For operation at submillimeter wavelengths and standoff ranges of many meters, the imaging targets are electrically very close to the antenna aperture. Therefore the main reflector surface must be an ellipse, instead of a parabola, in order to achieve the best imaging performance. Here we demonstrate how a simple design equivalence can be used to generalize the design of a Gregorian reflector system based on a paraboloidal main reflector to one with an ellipsoidal main reflector. The system parameters are determined by minimizing the optical path length error, and the results are validated with numerical simulations from the commercial antenna software package GRASP. The system is able to scan the beam over 0.5 m in cross-range at a 25 m standoff range with less than 1% increase of the half-power beam-width

Association of physical and behavioral characteristics with menstrual cycle patterns in women age 29-31 years

Journal ArticleWe examined the association between menstrual cycle characteristics(cycle length, variability, and bleeding length) and physical and behavioral attributes in 766 women age 29-31 years. Menstrual cycled at a were prospectively recorded as part of the Menstruation and Reproductive History Study of college women in Minnesota, begun by Alan Treloar in 1934. Data on life time height, weight, physical activity, alcohol and caffeine consumption, and smoking history were collected in 1990 using a self-administered questionnaire. Cycle variability, as measured by the standard deviation of the cycle length, was increased, and menstrual cycles ≥-42 days in length were more common among women in the lowest quartile of Quetelet

Time-Delay Multiplexing of Two Beams in a Terahertz Imaging Radar

We demonstrate a time-delay multiplexing technique that doubles the frame rate of a 660–690-GHz imaging radar with minimal additional instrument complexity. This is done by simultaneously projecting two offset, orthogonally polarized radar beams generated and detected by a common source and receiver. Beam splitting and polarization rotation is accomplished with a custom designed waveguide hybrid coupler and twist. A relative time lag of approximately 2 ns between the beams’ waveforms is introduced using a quasi-optical delay line, followed by spatial recombination using a selectively reflective wire grid. This delay is much longer than the approximately 20-ps time-of-flight resolution of the 30-GHz bandwidth radar, permitting the two beams’ reflected signals from a compact target to be easily distinguished in digital post-processing of the single receiver channel

Experimental Temperature Analysis of Powder-Based Electron Beam Additive Manufacturing

A near infrared thermal imager has been employed for temperature measurements (build part surfaces) in the powder-based electron beam additive manufacturing (EBAM) process. A methodology has also been developed to analyze temperature distributions and history around the melting scan area. The temperature profiles along the beam scanning clearly show the moving source of heat phenomenon, with the peak temperature reaching over 2000 °C (for Ti6Al-4V) followed by extremely rapid cooling opposite to the beam scanning direction, except a slow-cooling portion corresponding to the liquidus-solidus range. The build surface temperatures and the melt pool sizes, in the localized electron beam scanning area, were studied at various configurations, e.g., different build heights, also with or without an overhang.Mechanical Engineerin

Improved fidelity of triggered entangled photons from single quantum dots

We demonstrate the on-demand emission of polarisation-entangled photon pairs from the biexciton cascade of a single InAs quantum dot embedded in a GaAs/AlAs planar microcavity. Improvements in the sample design blue shifts the wetting layer to reduce the contribution of background light in the measurements. Results presented show that >70% of the detected photon pairs are entangled. The high fidelity of the (|HxxHx>+|VxxVx>)/2^0.5 state that we determine is sufficient to satisfy numerous tests for entanglement. The improved quality of entanglement represents a significant step towards the realisation of a practical quantum dot source compatible with applications in quantum information.Comment: 9 pages. Paper is available free of charge at http://www.iop.org/EJ/abstract/1367-2630/8/2/029/, see also 'A semiconductor source of triggered entangled photon pairs', R. M. Stevenson et al., Nature 439, 179 (2006

Penetrating 3-D Imaging at 4- and 25-m Range Using a Submillimeter-Wave Radar

We show experimentally that a high-resolution imaging radar operating at 576–605 GHz is capable of detecting weapons concealed by clothing at standoff ranges of 4–25 m. We also demonstrate the critical advantage of 3-D image reconstruction for visualizing hidden objects using active-illumination coherent terahertz imaging. The present system can image a torso with <1 cm resolution at 4 m standoff in about five minutes. Greater standoff distances and much higher frame rates should be achievable by capitalizing on the bandwidth, output power, and compactness of solid state Schottky-diode based terahertz mixers and multiplied sources

Evaluation of Additively Manufactured Metals for Use in Oxygen Systems Project

Space Launch System, Commercial Resupply, and Commercial Crew programs have published intent to use additively manufactured (AM) components in propulsion systems and are likely to include various life support systems in the future. Parts produced by these types of additive manufacturing techniques have not been fully evaluated for use in oxygen systems and the inherent risks have not been fully identified. Some areas of primary concern in the SLS process with respect to oxygen compatibility may be the porosity of the printed parts, fundamental differences in microstructure of an AM part as compared to traditional materials, or increased risk of shed metal particulate into an oxygen system. If an ignition were to occur the printed material could be more flammable than components manufactured from a traditional billet of raw material and/or present a significant hazards if not identified and rigorously studied in advance of implementation into an oxygen system

Multifrequency radar observations of clouds and precipitation including the G-band

Observatory clearly demonstrate the potential of G-band radars for cloud and precipitation research, something that until now was only discussed in theory. The field experiment, which coordinated an X-, Ka-, W- and G-band radar, revealed that the Ka–G pairing can generate differential reflectivity signal several decibels larger than the traditional Ka–W pairing underpinning an increased sensitivity to smaller amounts of liquid and ice water mass and sizes. The observations also showed that G-band signals experience non-Rayleigh scattering in regions where Ka- and W-band signal do not, thus demonstrating the potential of G-band radars for sizing sub-millimeter ice crystals and droplets. Observed peculiar radar reflectivity patterns also suggest that G-band radars could be used to gain insight into the melting behavior of small ice crystals. G-band signal interpretation is challenging, because attenuation and non-Rayleigh effects are typically intertwined. An ideal liquid-free period allowed us to use triple-frequency Ka–W–G observations to test existing ice scattering libraries, and the results raise questions on their comprehensiveness. Overall, this work reinforces the importance of deploying radars (1) with sensitivity sufficient enough to detect small Rayleigh scatters at cloud top in order to derive estimates of path-integrated hydrometeor attenuation, a key constraint for microphysical retrievals; (2) with sensitivity sufficient enough to overcome liquid attenuation, to reveal the larger differential signals generated from using the G-band as part of a multifrequency deployment; and (3) capable of monitoring atmospheric gases to reduce related uncertainty

Fabrication of Turbine Disk Materials by Additive Manufacturing

Precipitation-strengthened, nickel-based superalloys are widely used in the aerospace and energy industries due to their excellent environmental resistance and outstanding mechanical properties under extreme conditions. Powder-bed additive manufacturing (AM) technologies offer the potential to revolutionize the processing of superalloy turbine components by eliminating the need for extensive inventory or expensive legacy tooling. Like selective laser melting (SLM), electron beam melting (EBM) constructs three-dimensional dense components layer-by-layer by melting and solidification of atomized, pre-alloyed powder feedstock within 50-200 micron layers. While SLM has been more widely used for AM of nickel alloys like 718, EBM offers several distinct advantages, such as less retained residual stress, lower risk of contamination, and faster build rates with multiple-electron-beam configurations. These advantages are particularly attractive for turbine disks, for which excessive residual stress and contamination can shorten disk life during high-temperature operation. In this presentation, we will discuss the feasibility of fabricating disk superalloy components using EBM AM. Originally developed using powder metallurgy forging processing, disk superalloys contain a higher refractory content and precipitate volume fraction than alloy 718, thus making them more prone to thermal cracking during AM. This and other challenges to produce homogeneous builds with desired properties will be presented. In particular, the quality of lab-scale samples fabricated via a design of experiments, in which the beam current, build temperature, and beam velocity were varied, will be summarized. The relationship between processing parameters, microstructure, grain orientation, and mechanical response will be discussed