Data correlation and analysis of arc tunnel and wind tunnel tests of RSI joints and gaps, phase 2. Volume 2: Data report, part 2

For abstract, see N75-28103

Silica heat shield sizing

The sensitivity of silica heat shield requirements to gap width, tile edge radius, and heat transfer distribution within tile gaps was investigated. A two-dimensional thermal model was modified and used to determine the effect of two dimensional heat transfer distributions at high temperature reusable surface insulation edges on shuttle thermal protection system (TPS) requirements. The sensitivity of TPS requirements to coating thickness, emissivity, substructure thickness, and changes in gap heating for several locations on shuttle was also studied. An inverse solution technique was applied to temperature data obtained in the Ames 20 MW turbulent duct in order to examine the effect of tile edge radius on TPS requirements. The derived heating values were then used to predict TPS requirements. Results show that increasing tile radius reduces TPS requirements

Data correlation and analysis of arc tunnel and wind tunnel tests of RSI joints and gaps. Volume 1: Technical report

Heat transfer data measured in gaps typical of those under consideration for joints in space shuttle reusable surface insulation protection systems have been assimilated, analyzed and correlated. The data were obtained in four NASA facilities. Several types of gaps were investigated with emphasis on simple butt joints. Gap widths ranged from 0.07 to 0.7 cm and depths ranged from 1 to 6 cm. Laminar, transitional and turbulent boundary layer flows over the gap opening were investigated. Three-dimensional heating variations were observed within gaps in the absence of external flow pressure gradients. Heat transfer correlation equations were obtained for several of the tests. Thermal protection system performance with and without gaps was compared for a representative shuttle entry trajectory

Lattice vibrations and structural instability in Cesium near the cubic to tetragonal transition

Under pressure cesium undergoes a transition from a high-pressure fcc phase (Cs-II) to a collapsed fcc phase (Cs-III) near 4.2GPa. At 4.4GPa there follows a transition to the tetragonal Cs-IV phase. In order to investigate the lattice vibrations in the fcc phase and seek a possible dynamical instability of the lattice, the phonon spectra of fcc-Cs at volumes near the III-IV transition are calculated using Savrasov's density functional linear-response LMTO method. Compared with quasiharmonic model calculations including non-central interatomic forces up to second neighbours, at the volume $V/V_0= 0.44$ ($V_0$ is the experimental volume of bcc-Cs with $a_0$=6.048{\AA}), the linear-response calculations show soft intermediate wavelength $T_{[1\bar{1}0]}[{\xi}{\xi}0]$ phonons. Similar softening is also observed for short wavelength $L[\xi\xi\xi]$ and $L[00\xi]$ phonons and intermediate wavelength $L[\xi\xi\xi]$ phonons. The Born-von K\'{a}rm\'{a}n analysis of dispersion curves indicates that the interplanar force constants exhibit oscillating behaviours against plane spacing $n$ and the large softening of intermediate wavelength $T_{[1\bar{1}0]}[{\xi}{\xi}0]$ phonons results from a negative (110)-interplanar force-constant $\Phi_{n=2}$. The frequencies of the $T_{[1\bar{1}0]}[{\xi}{\xi}0]$ phonons with $\xi$ around 1/3 become imaginary and the fcc structure becomes dynamically unstable for volumes below $0.41V_0$. It is suggested that superstructures corresponding to the $\mathbf{q}{\neq}0$ soft mode should be present as a precursor of tetragonal Cs-IV structure.Comment: 12 pages, 5 figure

The Top Triangle Moose

We introduce a deconstructed model that incorporates both Higgsless and top-color mechanisms. The model alleviates the typical tension in Higgsless models between obtaining the correct top quark mass and keeping delta-rho small. It does so by singling out the top quark mass generation as arising from a Yukawa coupling to an effective top-Higgs which develops a small vacuum expectation value, while electroweak symmetry breaking results largely from a Higgsless mechanism. As a result, the heavy partners of the SM fermions can be light enough to be seen at the LHC.Comment: To appear in proceedings of SCGT09, Nagoya, Japan. 5 page

Planetary/DOD entry technology flight experiments. Volume 4: DOD entry flight experiments

For abstract, see vol. 1

Planetary/DOD entry technology flight experiments. Volume 3: Planetary entry flight experiments handbook

The environments produced by entry into Jupiter and Saturn atmospheres are summarized. Worst case design environments are identified and the effect of entry angle, type of atmosphere and ballistic coefficient variations are presented. The range of environments experienced during earth entry is parametrically described as a function of initial entry conditions. The sensitivity of these environments to vehicle ballistic coefficient and nose radius is also shown. An elliptical deorbit maneuver strategy is defined in terms of the velocity increment required versus initial entry conditions and apoapsis altitude. Mission time, ground track, and out of plane velocity penalties are also presented. Performance capabilities of typical shuttle launched boosters are described including the initial entry conditions attainable as a function of paylaod mass and apoapsis altitude

Planetary/DOD entry technology flight experiments. Volume 1: Executive summary

The feasibility of using the space shuttle to launch planetary and DoD entry flight experiments was examined. The results of the program are presented in two parts: (1) simulating outer planet environments during an earth entry test, the prediction of Jovian and earth radiative heating dominated environments, mission strategy, booster performance and entry vehicle design, and (2) the DoD entry test needs for the 1980's, the use of the space shuttle to meet these DoD test needs, modifications of test procedures as pertaining to the space shuttle, modifications to the space shuttle to accommodate DoD test missions and the unique capabilities of the space shuttle. The major findings of this program are summarized

Optimization of graded multilayer designs for astronomical x-ray telescopes

We developed a systematic method for optimizing the design of depth-graded multilayers for astronomical hard-x-ray and soft-γ-ray telescopes based on the instrument’s bandpass and the field of view. We apply these methods to the design of the conical-approximation Wolter I optics employed by the balloon-borne High Energy Focusing Telescope, using W/Si as the multilayer materials. In addition, we present optimized performance calculations of mirrors, using other material pairs that are capable of extending performance to photon energies above the W K-absorption edge (69.5 keV), including Pt/C, Ni/C, Cu/Si, and Mo/Si