On the scaling behaviour of cross-tie domain wall structures in patterned NiFe elements

The cross-tie domain wall structure in micrometre and sub-micrometre wide patterned elements of NiFe, and a thickness range of 30 to 70nm, has been studied by Lorentz microscopy. Whilst the basic geometry of the cross-tie repeat units remains unchanged, their density increases when the cross-tie length is constrained to be smaller than the value associated with a continuous film. This occurs when element widths are sufficiently narrow or when the wall is forced to move close to an edge under the action of an applied field. To a very good approximation the cross-tie density scales with the inverse of the distance between the main wall and the element edge. The experiments show that in confined structures, the wall constantly modifies its form and that the need to generate, and subsequently annihilate, extra vortex/anti-vortex pairs constitutes an additional source of hysteresis.Comment: 4 pages, 5 figures, accepted for publication in Europhysics Letters (EPL

Squeezing out the last 1 nanometer of water: A detailed nanomechanical study

In this study, we present a detailed analysis of the squeeze-out dynamics of nanoconfined water confined between two hydrophilic surfaces measured by small-amplitude dynamic atomic force microscopy (AFM). Explicitly considering the instantaneous tip-surface separation during squeezeout, we confirm the existence of an adsorbed molecular water layer on mica and at least two hydration layers. We also confirm the previous observation of a sharp transition in the viscoelastic response of the nanoconfined water as the compression rate is increased beyond a critical value (previously determined to be about 0.8 nm/s). We find that below the critical value, the tip passes smoothly through the molecular layers of the film, while above the critical speed, the tip encounters "pinning" at separations where the film is able to temporarily order. Pre-ordering of the film is accompanied by increased force fluctuations, which lead to increased damping preceding a peak in the film stiffness once ordering is completed. We analyze the data using both Kelvin-Voigt and Maxwell viscoelastic models. This provides a complementary picture of the viscoelastic response of the confined water film

Reactive Boundary Conditions as Limits of Interaction Potentials for Brownian and Langevin Dynamics

A popular approach to modeling bimolecular reactions between diffusing molecules is through the use of reactive boundary conditions. One common model is the Smoluchowski partial absorption condition, which uses a Robin boundary condition in the separation coordinate between two possible reactants. This boundary condition can be interpreted as an idealization of a reactive interaction potential model, in which a potential barrier must be surmounted before reactions can occur. In this work we show how the reactive boundary condition arises as the limit of an interaction potential encoding a steep barrier within a shrinking region in the particle separation, where molecules react instantly upon reaching the peak of the barrier. The limiting boundary condition is derived by the method of matched asymptotic expansions, and shown to depend critically on the relative rate of increase of the barrier height as the width of the potential is decreased. Limiting boundary conditions for the same interaction potential in both the overdamped Fokker-Planck equation (Brownian Dynamics), and the Kramers equation (Langevin Dynamics) are investigated. It is shown that different scalings are required in the two models to recover reactive boundary conditions that are consistent in the high friction limit where the Kramers equation solution converges to the solution of the Fokker-Planck equation.Comment: 23 pages, 2 figure

A Program of Photometric Measurements of Solar Irradiance Fluctuations from Ground-based Observations

Photometric observations of the sun have been carried out at the San Fernando Observatory since early 1985. Since 1986, observations have been obtained at two wavelengths in order to separately measure the contributions of sunspots and bright facular to solar irradiance variations. Researchers believe that the contributions of sunspots can be measured to an accuracy of about plus or minus 30 ppm. The effect of faculae is much less certain, with uncertainties in the range of plus or minus 300 ppm. The larger uncertainty for faculae reflects both the greater difficulty in measuring the facular area, due to their lower contrast compared to sunspots, and the greater uncertainty in their contrast variation with viewing angle on the solar disk. Recent results from two separate photometric telescopes will be compared with bolometric observations from the active cavity radiometer irradiance monitor (ACRIM) that was on board the Solar Max satellite

Real-time detection of individual atoms falling through a high-finesse optical cavity

The enhanced coupling between atoms and photons inside a high-finesse optical cavity provides a novel basis for optical measurements that continuously monitor atomic degrees of freedom. We describe an experiment in which cavity quantum-electrodynamic effects are utilized for real-time detection of individual atoms falling through an optical cavity after being dropped from a magneto-optical trap. Our technique permits experiments that are triggered by the presence of a single optimally coupled atom within the cavity mode volume

A process activity monitor for AOS/VS

With the ever increasing concern for computer security, users of computer systems are becoming more sensitive to unauthorized access. One of the initial security concerns for the Shuttle Management Information System was the problem of users leaving their workstations unattended while still connected to the system. This common habit was a concern for two reasons: it ties up resources unnecessarily and it opens the way for unauthorized access to the system. The Data General MV/10000 does not come equipped with an automatic time-out option on interactive peripherals. The purpose of this memorandum is to describe a system which monitors process activity on the system and disconnects those users who show no activity for some time quantum

Analytical and experimental investigations of low level acceleration measurement techniques

Construction techniques for accelerometer with low level threshold sensitivit