29,621 research outputs found
Diffusion bonding of IN 718 to VM 350 grade maraging steel
Diffusion bonding studies have been conducted on IN 718, VM 350 and the dissimilar alloy couple, IN 718 to maraging steel. The experimental processing parameters critical to obtaining consistently good diffusion bonds between IN 718 and VM 350 were determined. Interrelationships between temperature, pressure and surface preparation were explored for short bending intervals under vacuum conditions. Successful joining was achieved for a range of bonding cycle temperatures, pressures and surface preparations. The strength of the weaker parent material was used as a criterion for a successful tensile test of the heat treated bond. Studies of VM-350/VM-350 couples in the as-bonded condition showed a greater yielding and failure outside the bond region
Transition mixing study
A computer model capable of analyzing the flow field in the transition liner of small gas turbine engines is developed. A FORTRAN code has been assembled from existing codes and physical submodels and used to predict the flow in several test geometries which contain characteristics similar to transition liners, and for which experimental data was available. Comparisons between the predictions and measurements indicate that the code produces qualitative results but that the turbulence models, both K-E and algebraic Reynolds Stress, underestimate the cross-stream diffusion. The code has also been used to perform a numerical experiment to examine the effect of a variety of parameters on the mixing process in transition liners. Comparisons illustrate that geometries with significant curvature show a drift of the jet trajectory toward the convex wall and weaker wake region vortices and decreased penetration for jets located on the convex wall of the liner, when compared to jets located on concave walls. Also shown were the approximate equivalency of angled slots and round holes and a technique by which jet mixing correlations developed for rectangular channels can be used for can geometries
An extended multi-zone model for the MCG-6-30-15 warm absorber
The variable warm absorber seen with {\em ASCA} in the X-ray spectrum of
MCG6-30-15 shows complex time behaviour in which the optical depth of OVIII
anticorrelates with the flux whereas that of OVII is unchanging. The
explanation in terms of a two zone absorber has since been challenged by {\em
BeppoSAX} observations. These present a more complicated behaviour for the
OVIII edge. We demonstrate here that the presence of a third, intermediate,
zone can explain all the observations. In practice, warm absorbers are likely
to be extended, multi-zone regions of which only part causes directly
observable absorption edges at any given time.Comment: 5 pages, 6 figures, accepted for publication in MNRA
An Assessment of Potential Detectors to Monitor the Man-made Orbital Debris Environment
Observations using NORAD radar showed that man made debris exceeds the natural environment for large objects. For short times (a few days to a few weeks) after solid rocket motor (SRM) firings in LEO, man made debris in the microparticle size range also appears to exceed the meteoroid environment. The properties of the debris population between these size regimes is currently unknown as there has been no detector system able to perform the required observations. The alternatives for obtaining data on this currently unobserved segment of the population are assessed
Iron fluorescence from within the innermost stable orbit of black hole accretion disks
The fluorescent iron Ka line is a powerful observational probe of the inner
regions of black holes accretion disks. Previous studies have assumed that only
material outside the radius of marginal stability can contribute to the
observed line emission. Here, we show that fluorescence by material inside the
radius of marginal stability, which is in the process of spiralling towards the
event horizon, can have a observable influence on the iron line profile and
equivalent width. For concreteness, we consider the case of a geometrically
thin accretion disk, around a Schwarzschild black hole, in which fluorescence
is excited by an X-ray source placed at some height above the disk and on the
axis of the disk. Fully relativistic line profiles are presented for various
source heights and efficiencies. It is found that the extra line flux generally
emerges in the extreme red wing of the iron line, due to the large
gravitational redshift experienced by photons from the region within the radius
of marginal stability. We apply our models to the variable iron line seen in
the ASCA spectrum of the Seyfert nucleus MCG-6-30-15. It is found that the
change in the line profile, equivalent width, and continuum normalization, can
be well explained as being due to a change in the height of the source above
the disk. We discuss the implications of these results for distinguishing
rapidly-rotating black holes from slowly rotating holes using iron line
diagnostics.Comment: 20 pages, LaTeX. Accepted for publication in Astrophysical Journal.
Figures 3 to 7 replaced with corrected versions (previous figures affected by
calculational error). Some changes in the best fitting parameter
Occultation Mapping of the Central Engine in the Active Galaxy MCG -6-30-15
The colossal power output of active galactic nuclei (AGN) is believed to be
fueled by the accretion of matter onto a supermassive black hole. This central
accreting region of AGN has hitherto been spatially unresolved and its
structure therefore unknown. Here we propose that a previously reported `deep
minimum' in the X-ray intensity of the AGN MCG-6-30-15, was due to a unique
X-ray occultation event and that it probes structure of the central engine on
scales < 1e14 cm, or 1.4e-7 arcseconds. The data are consistent with a bright
central source surrounded by a less intense ring, which we identify with the
inner edge of an accretion disk. These may be the first direct measurements of
the spatial structure and geometry of the accreting black-hole system in an
active galaxy.If the ring of X-ray emission is identified with the inner edge
of an accretion disk, upper limits on the BH mass can be derived. Our
occultation interpretation is controversial in the sense that X-ray variability
in AGNs is normally attributed to intrinsic physical changes in the X-ray
emission region, such as disk or coronal instabilities.Comment: 15 pages, 2 Figures. Latex with separate postscript figure files.
Accepted for publication in ApJ Letter
A Search for Ionized Gas in the Draco and Ursa Minor Dwarf Spheroidal Galaxies
The Wisconsin H Alpha Mapper has been used to set the first deep upper limits
on the intensity of diffuse H alpha emission from warm ionized gas in the Local
Group dwarf spheroidal galaxies (dSphs) Draco and Ursa Minor. Assuming a
velocity dispersion of 15 km/s for the ionized gas, we set limits for the H
alpha intensity of less or equal to 0.024 Rayleighs and less or equal to 0.021
Rayleighs for the Draco and Ursa Minor dSphs, respectively, averaged over our 1
degree circular beam. Adopting a simple model for the ionized interstellar
medium, these limits translate to upper bounds on the mass of ionized gas of
approximately less than 10% of the stellar mass, or approximately 10 times the
upper limits for the mass of neutral hydrogen. Note that the Draco and Ursa
Minor dSphs could contain substantial amounts of interstellar gas, equivalent
to all of the gas injected by dying stars since the end of their main star
forming episodes more than 8 Gyr in the past, without violating these limits on
the mass of ionized gas.Comment: 10 pages, 2 figures, AASTeX two-column format. Accepted for
publication in The Astrophysical Journa
Evaluation of subgrid-scale turbulence models using a fully simulated turbulent flow
An exact turbulent flow field was calculated on a three-dimensional grid with 64 points on a side. The flow simulates grid-generated turbulence from wind tunnel experiments. In this simulation, the grid spacing is small enough to include essentially all of the viscous energy dissipation, and the box is large enough to contain the largest eddy in the flow. The method is limited to low-turbulence Reynolds numbers, in our case R sub lambda = 36.6. To complete the calculation using a reasonable amount of computer time with reasonable accuracy, a third-order time-integration scheme was developed which runs at about the same speed as a simple first-order scheme. It obtains this accuracy by saving the velocity field and its first-time derivative at each time step. Fourth-order accurate space-differencing is used
- …