Thermo-mechanical degradation of composite restoration photoactivated by modulated methods-a SEM study of marginal and internal gap formation

Objective. To evaluate the influence of thermal-mechanical degradation on superficial and internal gap formation of composite restorations photoactivated using modulated methods. Materials and methods. An experimental composite was prepared using a resin matrix containing 65wt% Bis-GMA and 35wt% TEGDMA. Camphorquinone (0.5wt%) and dimethylaminoethyl-methacrylate (0.5wt%) were dissolved in the resin as a photo-initiator system and 65wt.% silanized glass fillers were added to the matrix. Ground buccal surfaces of bovine lower incisors were used to make 160 preparations (3 mm x 3 mm x 2 mm in depth). An adhesive system (Adper Single Bond 2) was applied and the specimens were assigned into 16 groups (n = 10), according to the photoactivation method [high intensity (HI), low intensity (LI), soft-start (SS) and pulse-delay (PD)] and the degradation protocol [(control/no degradation; thermal cycling (TC); mechanical loading (ML); thermo-mechanical loading (TC+ML)]. Marginal and internal interfaces of bonded restorations were replicated in epoxy resin and analyzed by SEM. Gaps were expressed as a percentage of the total length of the margins. Data were submitted to 2-way ANOVA and Tukey's test (alpha = 0.05). Results. For the control group no significance was noted among the photoactivation methods. TC had no effect in gap formation. ML and TC+ML increased the incidence of superficial gaps for both HI and SS groups as well as increased the internal gaps for all groups. Conclusion. Although photoactivation methods do not influence gap formation at first, composite restoration photoactivated by low intensity or modulated methods showed improved resistance to thermo-mechanical degradation. Mechanical loading is determinant for interfacial degradation of composite restorations, while thermal cycling has no effect on gap formation.7151341134

Clinical performance of a self-etching adhesive at 18 months

Purpose: To test the null hypothesis that beveling and/or etching enamel would not affect the 18-month clinical performance of the self-etching adhesive Clearfil SE Bond (CSEB) in noncarious cervical lesions (NCCL). Methods: With Institutional Review Board approval, 34 patients were enrolled in this study. A total of 120 NCCL was selected and assigned to four groups: (1) CSEB was applied without any cavity preparation; (2) CSEB was applied after beveling enamel; (3) CSEB was applied after etching enamel for 15 seconds with 35% phosphoric acid; (4) CSEB was applied after beveling and etching enamel. A microfilled composite resin was used for all restorations. Resuts: At 6 months after initial placement, 120 restorations (a 100% recall rate) were evaluated. At 18 months, 87 restorations (a 72.5% recall rate) were available for evaluation. A survival rate of 100% was measured for all groups at both 6 and 18 months. Sensitivity to air decreased significantly only for Group 3 (no bevel+acid etch) from baseline to 18 months without statistical changes from 6 months to 18 months. None of the other parameters resulted in significant differences for any of the four groups. However, when data were pooled, both the overall marginal discoloration and the overall marginal adaptation were significantly worse at 18 months than at baseline, while sensitivity to air decreased significantly from baseline to 18 months. The 18-month survival rate of the self-etching adhesive Clearfil SE Bond was not improved by enamel bevel or by enamel etching. Both overall marginal adaptation and overall marginal discoloration were worse at 18 months than at baseline

Morphology and topography analysis of mesoporous titania templated by micrometric latex sphere arrays

In this work, mesoporous titania is prepared by templating latex sphere arrays with four different sphere diameters at the micrometric scale (phi > 1 mu m). The mesoporous titania homogeneously covers the latex spheres and substrate, forming a thin coating characterized by N-2 adsorption isotherm, small angle X-rays scattering, atomic force, field emission and transmission electronic microscopies. Mesoporous titania has been templated into different shapes such as hollow particles and monoliths according to the amount of sol used to fill the voids of the close packed latex spheres. Titania topography strongly depends on the adsorption of polymeric segments over latex spheres surface, which could be decreased by changing the dimensions of latex spheres (phi = 9.5 mu m) generating a lamellar architecture. Thus, micrometric latex sphere arrays can be used to achieve new surface patterns for mesoporous materials via a fast and inexpensive chemical route for construction of functional devices in different technological fields such as energy conversion, inclusion chemistry and biomaterials. (C) 2011 Elsevier Inc. All rights reserved.Fundacao de Amparo a Pesquisa do Estado de Sao Paulo (FAPESP)Fundacao de Amparo a Pesquisa do Estado de Sao Paulo (FAPESP) [2008/00463-2]Chemistry Institute of the University of Sao Paulo, BrazilChemistry Institute of the University of Sao Paulo, Brazi

Morphology and topography analysis of mesoporous titania templated by micrometric latex sphere arrays

In this work, mesoporous titania is prepared by templating latex sphere arrays with four different sphere diameters at the micrometric scale (ϕ > 1 μm). The mesoporous titania homogeneously covers the latex spheres and substrate, forming a thin coating characterized by N2 adsorption isotherm, small angle X-rays scattering, atomic force, field emission and transmission electronic microscopies. Mesoporous titania has been templated into different shapes such as hollow particles and monoliths according to the amount of sol used to fill the voids of the close packed latex spheres. Titania topography strongly depends on the adsorption of polymeric segments over latex spheres surface, which could be decreased by changing the dimensions of latex spheres (ϕ = 9.5 μm) generating a lamellar architecture. Thus, micrometric latex sphere arrays can be used to achieve new surface patterns for mesoporous materials via a fast and inexpensive chemical route for construction of functional devices in different technological fields such as energy conversion, inclusion chemistry and biomaterials1528495FUNDAÇÃO DE AMPARO À PESQUISA DO ESTADO DE SÃO PAULO - FAPESP2008/00463-