The effects of high-temperature brazing and thermal cycling on the mechanical properties of Hastelloy X

Data are presented on the effects of brazing alloy, brazing operation, thermal cycling, and combinations of these on the yield strength, elongation, tensile strength, and fatigue life of thin gage Hastelloy X. These data show that brazing at 1461 K (2170 F) with a Ni-Pd-Au alloy and subsequent exposure to 200 service thermal cycles between 533 and 1144 K (500 and 1600 F) result in reduction of as much as 39 percent in yield strength, 33 percent in elongation, 14 percent in tensile strength, and 26 percent in fatigue limit of Hastelloy X, as compared to as-received materials. These property losses are primarily caused by the brazing operation rather than the subsequent service thermal cycles

On Ptolemaic metric simplicial complexes

We show that under certain mild conditions, a metric simplicial complex which satisfies the Ptolemy inequality is a CAT(0) space. Ptolemy's inequality is closely related to inversions of metric spaces. For a large class of metric simplicial complexes, we characterize those which are isometric to Euclidean space in terms of metric inversions.Comment: 13 page

Erosion of iron-chromium alloys by glass particles

The material loss upon erosion was measured for several iron-chromium alloys. Two types of erodent material were used: spherical glass beads and sharp particles of crushed glass. For erosion with glass beads the erosion resistance (defined as the reciprocal of material loss rate) was linearly dependent on hardness. This is in accordance with the erosion behavior of pure metals, but contrary to the erosion behavior of alloys of constant composition that were subjected to different heat treatments. For erosion with crushed glass, however, no correlation existed between hardness and erosion resistance. Instead, the erosion resistance depended on alloy composition rather than on hardness and increased with the chromium content of the alloy. The difference in erosion behavior for the two types of erodent particles suggested that two different material removal mechanisms were involved. This was confirmed by SEM micrographs of the eroded surfaces, which showed that for erosion with glass beads the mechanism of material removal was deformation-induced flaking of surface layers, or peening, whereas for erosion with crushed glass it was cutting or chopping

Effects of erodant particle shape and various heat treatments on erosion resistance of plain carbon steel

Erosion tests were conducted on 1045 steel samples which had been subjected to different heat treatments. The weight of material removed upon erosion with glass beads and crushed glass was measured. The data show that there is no correlation between hardness and erosion resistance. The erosion rate was strongly dependent on the shape of erodant particles, being an order of magnitude higher for erosion with crushed glass than with glass beads. Heat treatment had a profound effect on the erosion resistance when the erodant particles were glass beads but little or no effect when the particles were crushed glass. It is thus concluded that different mechanisms of material removal are involved with these two erodants. This conclusion is supported by the surface morphology of annealed 1045 steel samples which had been eroded by these two types of erodant particles. SEM micrographs of the eroded surfaces show that for erosion with glass beads it is deformation induced fracture of surface layers

Effect of mechanical surface and heat treatments on erosion resistance

The effects of mechanical surface treatments as well as heat treatments on the erosion resistance of 6061 aluminum alloy and 1045 steel were studied. Mechanical surface treatments were found to have little or no effect on the erosion resistance. This is due to the formation by particle impact of a work hardened surface layer regardless of the initial surface condition. The erosion resistance of Al single crystals is found to be independent of orientation. This is due to destruction of the surface microstructure and formation of a polycrystalline surface layer by the impact of erodant particles as observed by X-ray diffraction. While upon solution treatment of annealed 6061 aluminum the increase in hardness is accompanied by an increase in erosion resistance, precipitation treatment which causes a further increase in hardness results in slightly lower erosion resistance. Using two types of erodant particles, glass beads and crushed glass, the erosion rate is found to be strongly dependent on erodant particle shape, being an order of magnitude higher for erosion with crushed glass as compared to glass beads. While for erosion with glass beads heat treatment of 1045 steel had a profound effect on its erosion resistance, little or no such effect was observed for erosion with crushed glass

One-step dual purpose joining technique

This fastener used in induction heating is a wire screen basically of an eddy current carrying material such as carbon steel. Selected wires in the screen are copper, sheathed in an insulating material. The screen is placed between two sheets of thermoplastics. When inductively heated, the composite softens and flows around the apertures of the screen. After this heating and joining, the copper wires may be used to conduct electricity

Complex surfaces plated by thin-film deposition in one operation

Ion plating deposits thin film on complex surface in one operation. The ionized materials follow electric lines of force to all points on the objects, uniformly plating the surface from all sides simultaneously

Low-temperature solder for joining large cryogenic structures

Three joining methods were considered for use in fabricating cooling coils for the National Transonic Facility. After analysis and preliminary testing, soldering was chosen as the cooling coil joining technique over mechanical force fit and brazing techniques. Charpy V-Notch tests, cyclic thermal tests (ambient to 77.8 K) and tensile tests at cryogenic temperatures were performed on solder joints to evaluate their structural integrity. It was determined that low temperature solder can be used to ensure good fin-to-tube contact for cooling-coil applications

Limiter Control of a Chaotic RF Transistor Oscillator

We report experimental control of chaos in an electronic circuit at 43.9 MHz, which is the fastest chaos control reported in the literature to date. Limiter control is used to stabilize a periodic orbit in a tuned collector transistor oscillator modified to exhibit simply folded band chaos. The limiter is implemented using a transistor to enable monitoring the relative magnitude of the control perturbation. A plot of the relative control magnitude vs. limiter level shows a local minimum at period-1 control, thereby providing strong evidence that the controlled state is an unstable periodic orbit (UPO) of the uncontrolled system