51 research outputs found
Differences in Iron Removal from Carbon Nanoonions and Multiwall Carbon Nanotubes for Analytical Purpose
The paper describes the differences between wet iron removal from carbon nanoonions and from multiwall carbon nanotubes for analytical purpose. Nowadays, both carbon nanoonions and multiwall carbon nanotubes are one of the most interesting materials with applicability in electronics, medicine and biotechnology. Medical applications of those nanomaterials require not only recognition of their structure but also measurement of metal impurities concentration. Inductively coupled plasma optical emission spectrometry as a method for Fe-determination requires liquid samples. Hence, we propose various protocols for leaching of iron from studied materials. Our results proved that structure of nanomaterials have an impact on the efficiency of iron removal
Differences in Iron Removal from Carbon Nanoonions and Multiwall Carbon Nanotubes for Analytical Purpose
The paper describes the differences between wet iron removal from carbon nanoonions and from multiwall carbon nanotubes for analytical purpose. Nowadays, both carbon nanoonions and multiwall carbon nanotubes are one of the most interesting materials with applicability in electronics, medicine and biotechnology. Medical applications of those nanomaterials require not only recognition of their structure but also measurement of metal impurities concentration. Inductively coupled plasma optical emission spectrometry as a method for Fe-determination requires liquid samples. Hence, we propose various protocols for leaching of iron from studied materials. Our results proved that structure of nanomaterials have an impact on the efficiency of iron removal
En route to controlled catalytic CVD synthesis of densely packed and vertically aligned nitrogen-doped carbon nanotube arrays
The catalytic chemical vapour deposition (c-CVD) technique was applied in the synthesis of vertically aligned arrays of nitrogen-doped carbon nanotubes (N-CNTs). A mixture of toluene (main carbon source), pyrazine (1,4-diazine, nitrogen source) and ferrocene (catalyst precursor) was used as the injection feedstock. To optimize conditions for growing the most dense and aligned N-CNT arrays, we investigated the influence of key parameters, i.e., growth temperature (660, 760 and 860 °C), composition of the feedstock and time of growth, on morphology and properties of N-CNTs. The presence of nitrogen species in the hot zone of the quartz reactor decreased the growth rate of N-CNTs down to about one twentieth compared to the growth rate of multi-wall CNTs (MWCNTs). As revealed by electron microscopy studies (SEM, TEM), the individual N-CNTs (half as thick as MWCNTs) grown under the optimal conditions were characterized by a superior straightness of the outer walls, which translated into a high alignment of dense nanotube arrays, i.e., 5 × 108 nanotubes per mm2 (100 times more than for MWCNTs grown in the absence of nitrogen precursor). In turn, the internal crystallographic order of the N-CNTs was found to be of a ‘bamboo’-like or ‘membrane’-like (multi-compartmental structure) morphology. The nitrogen content in the nanotube products, which ranged from 0.0 to 3.0 wt %, was controlled through the concentration of pyrazine in the feedstock. Moreover, as revealed by Raman/FT-IR spectroscopy, the incorporation of nitrogen atoms into the nanotube walls was found to be proportional to the number of deviations from the sp2-hybridisation of graphene C-atoms. As studied by XRD, the temperature and the [pyrazine]/[ferrocene] ratio in the feedstock affected the composition of the catalyst particles, and hence changed the growth mechanism of individual N-CNTs into a ‘mixed base-and-tip’ (primarily of the base-type) type as compared to the purely ‘base’-type for undoped MWCNTs
Electrophoretic deposition of layer-by-layer unsheathed carbon nanotubes - A step towards steerable surface roughness and wettability
It is well known that carbon nanotube (CNT) oxidation (usually with concentrated HNO3) is a major step before the electrophoretic deposition (EPD). However, the recent discovery of the “onion effect” proves that multiwalled carbon nanotubes are not only oxidized, but a simultaneous unsheathing process occurs. We present the first report concerning the influence of unsheathing on the properties of the thus-formed CNT surface layer. In our study we examine how the process of gradual oxidation/unsheathing of a series of multiwalled carbon nanotubes (MWCNTs) influences the morphology of the surface formed via EPD. Taking a series of well-characterized and gradually oxidized/unsheathing Nanocyl™ MWCNTs and performing EPD on a carbon fiber surface, we analyzed the morphology and wettability of the CNT surfaces. Our results show that the water contact angle could be gradually changed in a wide range (125–163°) and the major property determining its value was the diameter of aggregates formed before the deposition process in the solvent. Based on the obtained results we determined the parameters having a crucial influence on the morphology of created layers. Our results shed new light on the deposition mechanism and enable the preparation of surfaces with steerable roughness and wettability
The operational window of carbon nanotube electrical wires treated with strong acids and oxidants
Conventional metal wires suffer from a significant degradation or complete failure in their electrical performance, when subjected to harsh oxidizing environments, however wires constructed from Carbon Nanotubes (CNTs) have been found to actually improve in their electrical performance when subjected to these environments. These opposing reactions may provide new and interesting applications for CNT wires. Yet, before attempting to move to any real-world harsh environment applications, for the CNT wires, it is essential that this area of their operation be thoroughly examined. To investigate this, CNT wires were treated with multiple combinations of the strongest acids and halogens. The wires were then subjected to conductivity measurements, current carrying capacity tests, as well as Raman, microscopy and thermogravimetric analysis to enable the identification of both the limits of oxidative conductivity boosting and the onset of physical damage to the wires. These experiments have led to two main conclusions. Firstly, that CNT wires may operate effectively in harsh oxidizing environments where metal wires would easily fail and secondly, that the highest conductivity increase of the CNT wires can be achieved through a process of annealing, acetone and HCl purification followed by either H2O2 and HClO4 or Br2 treatment
Strong, Light, Multifunctional Fibers of Carbon Nanotubes with Ultrahigh Conductivity
Broader applications of carbon nanotubes to real-world problems have largely gone unfulfilled
because of difficult material synthesis and laborious processing. We report high-performance
multifunctional carbon nanotube (CNT) fibers that combine the specific strength, stiffness, and
thermal conductivity of carbon fibers with the specific electrical conductivity of metals. These
fibers consist of bulk-grown CNTs and are produced by high-throughput wet spinning, the same
process used to produce high-performance industrial fibers. These scalable CNT fibers are
positioned for high-value applications, such as aerospace electronics and field emission, and can
evolve into engineered materials with broad long-term impact, from consumer electronics to
long-range power transmission
Aligned carbon nanotube–epoxy composites: the effect of nanotube organization on strength, stiffness, and toughness
10.1007/s10853-016-0228-6Journal of Materials Science512210005-1002
The nitrogen inversion in fused isoxazolidinyl derivatives of substituted uracil: synthesis, NMR and computational analysis
En route to controlled catalytic CVD synthesis of densely packed and vertically aligned nitrogen-doped carbon nanotube arrays
The catalytic chemical vapour deposition (c-CVD) technique was applied in the synthesis of vertically aligned arrays of nitrogendoped carbon nanotubes (N-CNTs). A mixture of toluene (main carbon source), pyrazine (1,4-diazine, nitrogen source) and ferrocene (catalyst precursor) was used as the injection feedstock. To optimize conditions for growing the most dense and aligned N-CNT arrays, we investigated the influence of key parameters, i.e., growth temperature (660, 760 and 860 °C), composition of the feedstock and time of growth, on morphology and properties of N-CNTs. The presence of nitrogen species in the hot zone of the quartz reactor decreased the growth rate of N-CNTs down to about one twentieth compared to the growth rate of multi-wall CNTs (MWCNTs). As revealed by electron microscopy studies (SEM, TEM), the individual N-CNTs (half as thick as MWCNTs) grown under the optimal conditions were characterized by a superior straightness of the outer walls, which translated into a high alignment of dense nanotube arrays, i.e., 5 × 108 nanotubes per mm2 (100 times more than for MWCNTs grown in the absence of nitrogen precursor). In turn, the internal crystallographic order of the N-CNTs was found to be of a 'bamboo'-like or 'membrane'- like (multi-compartmental structure) morphology. The nitrogen content in the nanotube products, which ranged from 0.0 to 3.0 wt %, was controlled through the concentration of pyrazine in the feedstock. Moreover, as revealed by Raman/FT-IR spectroscopy, the incorporation of nitrogen atoms into the nanotube walls was found to be proportional to the number of deviations from the sp2-hybridisation of graphene C-atoms. As studied by XRD, the temperature and the [pyrazine]/[ferrocene] ratio in the feedstock affected the composition of the catalyst particles, and hence changed the growth mechanism of individual N-CNTs into a 'mixed base-and-tip' (primarily of the base-type) type as compared to the purely 'base'-type for undoped MWCNTs. © 2014 Boncel et al
Amalgamation of complex iron(III) ions and iron nanoclusters with MWCNTs as a route to potential T2 MRI contrast agents
Nikodem Kuźnik,1 Mateusz M Tomczyk,1 Marzena Wyskocka,1 Łukasz Przypis,1 Artur P Herman,1 Rafał Jędrysiak,1 Krzysztof K Koziol,2 Slawomir Boncel11Department of Organic Chemistry, Bioorganic Chemistry and Biotechnology, Faculty of Chemistry, Silesian University of Technology, Gliwice, Poland; 2Department of Materials Science and Metallurgy, University of Cambridge, Cambridge, UKAbstract: Iron-filled multiwall carbon nanotubes (Fe@MWCNTs) were functionalized toward a variety of potential magnetic resonance imaging contrast agents. Oxidized Fe@MWNCTs were covered with PEG5000 via direct esterification or using acyl chloride derivatives. Alternatively, the latter were functionalized with an aminophenol ligand (Fe@O-MWCNT-L). Moreover, pristine Fe@MWCNTs were functionalized with N-phenylaziridine groups (Fe@f-MWCNT) via [2+1] cycloaddition of nitrene. All of these chemically modified nanotubes served as a vehicle for anchoring Fe3+ ions. The new hybrids – Fe(III)/Fe@(f-/O-)MWCNTs – containing 6%–14% of the “tethered” Fe3+ ions were studied in terms of the acceleration of relaxation of water protons in nuclear magnetic resonance. The highest transverse relaxivity r2=63.9±0.9 mL mg-1 s-1 was recorded for Fe(III)/Fe@O-MWCNT-L, while for Fe(III)/Fe@f-MWCNT, with r2=57.9±2.9 mL mg-1 s-1, the highest impact of the anchored Fe(III) ions was observed. The T1/T2 ratio of 30–100 found for all of the nanotube hybrids presented in this work is a very important factor for their potential application as T2 contrast agents. Increased stability of the hybrids was confirmed by ultraviolet–visible spectrophotometry.Keywords: multiwall carbon nanotubes, Fe3+, transverse relaxation time T2, MRI contrast agen
- …