Investigation of plastic deformation heterogeneities in duplex steel by EBSD

An EBSD analysis of a duplex steel (austeno-ferritic) deformed in tension up to fracture is presented. The main purpose of the paper is to describe, qualitatively and quantitatively, the differences in the behavior of the two phases during plastic deformation. In order to do so, several topological maps are measured on the deformed state using the electron backscatter diffraction technique. Distributions of grain size, misorientation, image quality factor and texture are then analyzed in detail.International audienceAn EBSD analysis of a duplex steel (austeno-ferritic) deformed in tension up to fracture is presented. The main purpose of the paper is to describe, qualitatively and quantitatively, the differences in the behavior of the two phases during plastic deformation. In order to do so, several topological maps are measured on the deformed state using the electron backscatter diffraction technique. Distributions of grain size, misorientation, image quality factor and texture are then analyzed in detail

The hardening in alloys and composites and its examination with a diffraction and self-consistent model

The paper presents the results of diffraction stress measurement in Al/SiC composite and in 2124T6 aluminum alloy during the in situ tensile test. The main aim of the work is to observe the stress values for different stages of tensile test for the composite after applying two types of thermal treatment and for the alloy used as a matrix in this composite, to identify the type of hardening process. The experimental results were compared against the calculations results obtained from the self-consistent model developed by Baczmański [1] - [3] to gain the information about the micromechanical properties (critical resolved shear stress τ$_{cr}$ and hardening parameter H) of the examined materials. This comparison allowed researchers to determine the role of reinforcement in the composite as well as the impact of the heat treatment on the hardening of the material

A novel method of experimental determination of grain stresses and critical resolved shear stresses for slip and twin systems in a magnesium alloy

A novel original method of determination of stresses and critical resolved shear stresses (CRSSs) using neutron diffraction was proposed. In this method, based on the crystallite group method, the lattice strains were measured in different directions and using different reflections hkl during uniaxial deformation of magnesium alloy AZ31. The advantage of this method is that the stresses for groups of grains having similar orientations can be determined directly from measurement without any models used for data interpretation. The obtained results are unambiguous and do not depend on the models assumptions as in previous works. Moreover, it was possible for the first time to determine the uncertainty of the measured CRSS values and local stresses at groups of grains. The used methodology allowed for the determination of stress partitioning between grains having different orientations and for an explanation of the anisotropic mechanical behaviour of the strongly textured alloy. Finally, the CRSS values allowed for the validation of the type of intergranular interaction assumed in the elastic-plastic self-consistent model and for a significant reduction of the number of unknown parameters when the model is adjusted to the experimental data.Comment: 61 pages, 31 figures, 6 pages in Appendix, Accepted in Measuremen

A novel method of experimental determination of grain stresses and critical resolved shear stresses for slip and twin systems in a magnesium alloy

A novel original method of determination of stresses and critical resolved shear stresses (CRSSs) using neutron diffraction was proposed. In this method, based on the crystallite group method, the lattice strains were measured in different directions and using different reflections hkl during uniaxial deformation of magnesium alloy AZ31. The advantage of this method is that the stresses for groups of grains having similar orientations can be determined directly from measurement without any models used for data interpretation. The obtained results are unambiguous and do not depend on the models assumptions as in previous works. Moreover, it was possible for the first time to determine the uncertainty of the measured CRSS values and local stresses at groups of grains. The used methodology allowed for the determination of stress partitioning between grains having different orientations and for an explanation of the anisotropic mechanical behaviour of the strongly textured alloy. Finally, the CRSS values allowed for the validation of the type of intergranular interaction assumed in the elastic–plastic self-consistent model and for a significant reduction of the number of unknown parameters when the model is adjusted to the experimental data

Micromechanical Properties and Stress Measurements with Diffraction Methods

Diffraction methods are commonly used for the determination of the elastic lattice deformation and distortion from the displacement and broadening of the diffraction peak. These methods enable researchers to measure stresses and elastic properties of polycrystalline materials. The main advantages of diffraction methods are their non-destructive character and the possibility of macrostress and microstress analysis for multiphase and anisotropic materials. Measurements are performed selectively only for crystallites contributing to the measured diffraction peak, i.e. for the grains having lattice orientations for which the Bragg condition is satisfied. When several phases are present in the sample, measurements of separate diffraction peaks allow for the behaviour of each phase to be investigated independently. This method can be applied without any limitations to flat specimens. Numerical calculations of residual stresses around the rivets imply a very high stress gradientin the case of tangential stresses as well in the case of radial stresses. Attempting to verify these predictions, the residual stress measurements with an X-ray diffractometer were performed on riveted samples after the riveting process. In addition, complementary measurements of strain values with strain gauges during the riveting process were performed as well as the finite elements modelling. The aim of these measurements was to determine the stress values around the rivets and to compare results obtained with different techniques. On the other hand, the multi-scale crystallographic model of elastoplastic deformation is very convenient for the study of elastoplastic properties in microscopic and macroscopic scales. Comparison of experimental data with model predictions allows us to understand the physical phenomena that occur during a sample's deformation at the level of polycrystalline grains. Moreover, the micro and macro parameters of elastoplastic deformation can be experimentally established. It should be stated that the characterisation of the residual stress field and elastic properties is important in the study of the mechanical behaviour of polycrystalline materials, including plasticity and damage phenomena. In this work, a new analysis method of neutron diffraction results obtained during in-situ tensile load is proposed and tested. The methodology is based on the measurements of lattice strains during in-situ tensile testing for several hkl reflections and for different orientations of the sample with respect to the scattering vector. As the result, the full stress tensor for preferred texture orientations in function of the applied stress can be determined using the crystallite group method. The experimental data are presented and compared with the self-consistent model calculations performed for groups of grains selected by different hkl reflections

Micromechanical Properties and Stress Measurements with Diffraction Methods

Diffraction methods are commonly used for the determination of the elastic lattice deformation and distortion from the displacement and broadening of the diffraction peak. These methods enable researchers to measure stresses and elastic properties of polycrystalline materials. The main advantages of diffraction methods are their non-destructive character and the possibility of macrostress and microstress analysis for multiphase and anisotropic materials. Measurements are performed selectively only for crystallites contributing to the measured diffraction peak, i.e. for the grains having lattice orientations for which the Bragg condition is satisfied. When several phases are present in the sample, measurements of separate diffraction peaks allow for the behaviour of each phase to be investigated independently. This method can be applied without any limitations to flat specimens. Numerical calculations of residual stresses around the rivets imply a very high stress gradientin the case of tangential stresses as well in the case of radial stresses. Attempting to verify these predictions, the residual stress measurements with an X-ray diffractometer were performed on riveted samples after the riveting process. In addition, complementary measurements of strain values with strain gauges during the riveting process were performed as well as the finite elements modelling. The aim of these measurements was to determine the stress values around the rivets and to compare results obtained with different techniques. On the other hand, the multi-scale crystallographic model of elastoplastic deformation is very convenient for the study of elastoplastic properties in microscopic and macroscopic scales. Comparison of experimental data with model predictions allows us to understand the physical phenomena that occur during a sample's deformation at the level of polycrystalline grains. Moreover, the micro and macro parameters of elastoplastic deformation can be experimentally established. It should be stated that the characterisation of the residual stress field and elastic properties is important in the study of the mechanical behaviour of polycrystalline materials, including plasticity and damage phenomena. In this work, a new analysis method of neutron diffraction results obtained during in-situ tensile load is proposed and tested. The methodology is based on the measurements of lattice strains during in-situ tensile testing for several hkl reflections and for different orientations of the sample with respect to the scattering vector. As the result, the full stress tensor for preferred texture orientations in function of the applied stress can be determined using the crystallite group method. The experimental data are presented and compared with the self-consistent model calculations performed for groups of grains selected by different hkl reflections

Variation of residual stresses during cross-rolling

Residual stresses in cross-rolled polycrystalline copper and low carbon steel are studied. Cross-rolling modifies both residual stresses and crystallographic texture. Consequently, it can be used in order to improve the final properties of a material by introducing a given state of internal stress and by imposing more symmetry to the texture

Synchrotron Radiation Application for Lattice Strain Measurements

The methods most commonly used for the determination of the elastic lattice deformation and distortion are diffraction methods, which enable to perform measurements of stresses and elastic properties of polycrystalline materials. The main advantages of diffraction methods are associated with their non-destructive character and the possibility to be used for macrostress and microstress analysis of multiphase and anisotropic materials. Diffraction methods enable taking measurements selectively only for a chosen alloy phase. This is very convenient when several phases are present in the sample since measurements of separate diffraction peaks allow the behaviour of each phase to be investigated independently. In this work, a method for analysis of diffraction with synchrotron radiation is described. The methodology is based on the measurements of lattice strains during “in situ” tensile testing for several hkl reflections and for different orientations of the sample with respect to the scattering vector. Some initial results are presented

The Hardening in Alloys and Composites and Its Examination with a Diffraction and Self-Consistent Model

The paper presents the results of diffraction stress measurement in Al/SiC composite and in 2124T6 aluminum alloy during the in situ tensile test. The main aim of the work is to observe the stress values for different stages of tensile test for the composite after applying two types of thermal treatment and for the alloy used as a matrix in this composite, to identify the type of hardening process. The experimental results were compared against the calculations results obtained from the self-consistent model developed by Baczmański [1] - [3] to gain the information about the micromechanical properties (critical resolved shear stress τcr and hardening parameter H) of the examined materials. This comparison allowed researchers to determine the role of reinforcement in the composite as well as the impact of the heat treatment on the hardening of the material