Discussion of “Earth concrete. Stabilization revisited”

Using metrics is an informative approach to compare the effectiveness of cement use in material systems, but does not necessarily consider all factors needed to determine which system is most sustainable. To make a fair comparison, it is necessary to consider the functions cement performs in each system. In this discussion, suggestions are given for how to assess the use of cement as a binding agent in stabilised earth construction. Consideration of structural requirements and durability, life cycle analysis and moisture buffering shows that the effectiveness of cement use depends on more than just embodied carbon and dry compressive strength

Characterization of dry-stack interlocking compressed earth blocks

Earth has been a traditional building material to construct houses in Africa. One of the most common techniques is the use of sun dried or kiln fired adobe bricks with mud mortar. Fired bricks are the main cause for deforestation in countries like Malawi. Although this technique is low-cost, the bricks vary largely in shape, strength and durability. This leads to weak houses which suffer considerable damage during floods and seismic events. One solution is the use of dry-stack masonry with stabilized interlocking compressed earth blocks (ICEB). This technology has the potential of substituting the current bricks by a more sustainable kind of block. This study was made in the context of the HiLoTec project, which focuses on houses in rural areas of developing countries. For this study, Malawi was chosen for a case study. This paper presents the experimental results of tests made with dry-stack ICEBs. Soil samples from Malawi were taken and studied. Since the experimental campaign could not be carried out in Malawi, a homogenization process of Portuguese soil was made to produce ICEBs at the University of Minho, Portugal. Then, the compression and tensile strength of the materials was determined via small cylinder samples. Subsequently, the compression and flexural strength of units were determined. Finally, tests to determine the compressive strength of both prisms and masonry wallets and to determine the initial shear strength of the dry interfaces were carried out. This work provides valuable data for low-cost eco-efficient housingThis work was carried out under the research project HiLoTec - Development of a Sustainable Self-Construction System for Developing Countries. The authors wish to thank Mota-Engil Constructing Group for supporting this project

The impact of cyclic wetting and drying on the swelling behaviour of stabilized expansive soils

Black cotton soil (BCS) deposits, stabilized with waste materials-wood-ash and organic matter (leaves, grass, etc.) exist in BCS areas of North Karnataka, India. These ash-modified soils (AMS) are apparently stabilized by hydrated lime produced by biochemical, dissolution, and hydration reactions. The influence of cyclic wetting and drying on the swelling behaviour of wood-ash-modified BCS and laboratory lime-treated BCS specimens are examined in this study. Such a study is required to assess the long-term behaviour of chemically stabilized soils in geotechnical applications. Cyclic wetting and drying caused the AMS specimens to become more porous and less saturated. Consequently, the cyclically wetted and dried (or desiccated) AMS specimens collapsed significantly at the experimental flooding pressures. The beneficial effects of lime-stabilization of the BCS specimens were also partially lost in cyclically wetting and drying them. The clay contents of the lime-treated BCS specimens increased on cyclic wetting and drying. The increased clay contents in turn, affected their Atterberg limits and swell–shrink potentials. Partial loss of inter-particle cementation, increased porosity, and reduced degree of saturation, also imparted small to moderate collapse potentials to the desiccated lime-treated BCS specimens

The impact of cyclic wetting and drying on the swelling behaviour of stabilized expansive soils

Black cotton soil (BCS) deposits, stabilized with waste materials-wood-ash and organic matter (leaves, grass, etc.) exist in BCS areas of North Karnataka, India. These ash-modified soils (AMS) are apparently stabilized by hydrated lime produced by biochemical, dissolution, and hydration reactions. The influence of cyclic wetting and drying on the swelling behaviour of wood-ash-modified BCS and laboratory lime-treated BCS specimens are examined in this study. Such a study is required to assess the long-term behaviour of chemically stabilized soils in geotechnical applications. Cyclic wetting and drying caused the AMS specimens to become more porous and less saturated. Consequently, the cyclically wetted and dried (or desiccated) AMS specimens collapsed significantly at the experimental flooding pressures. The beneficial effects of lime-stabilization of the BCS specimens were also partially lost in cyclically wetting and drying them. The clay contents of the lime-treated BCS specimens increased on cyclic wetting and drying. The increased clay contents in turn, affected their Atterberg limits and swell–shrink potentials. Partial loss of inter-particle cementation, increased porosity, and reduced degree of saturation, also imparted small to moderate collapse potentials to the desiccated lime-treated BCS specimens

Biomethanation of herbaceous biomass residues using 3-zone plug flow like digesters - A case study from India

Biomethanation of herbaceous biomass feedstock has the potential to provide clean energy source for cooking and other activities in areas where such biomass availability predominates. A biomethanation concept that involves fermentation of biomass residues in three steps, occurring in three zones of the fermentor is described. This approach while attempting take advantage of multistage reactors simplifies the reactor operation and obviates the need for a high degree of process control or complex reactor design. Typical herbaceous biomass decompose with a rapid VFA flux initially (with a tendency to float) followed by a slower decomposition showing balanced process of VFA generation and its utilization by methanogens that colonize biomass slowly. The tendency to float at the initial stages is suppressed by allowing previous days feed to hold it below digester liquid which permits VFA to disperse into the digester liquid without causing process inhibition. This approach has been used to build and operate simple biomass digesters to provide cooking gas in rural areas with weed and agro-residues. With appropriate modifications, the same concept has been used for digesting municipal solid wastes in small towns where large fermentors are not viable. With further modifications this concept has been used for solid-liquid feed fermentors. Methanogen colonized leaf biomass has been used as biofilm support to treat coffee processing wastewater as well as crop litter alternately in a year. During summer it functions as a biomass based biogas plants operating in the three-zone mode while in winter, feeding biomass is suspended and high strength coffee processing wastewater is let into the fermentor achieving over 90% BOD reduction. The early field experience of these fermentors is presented

Design of a climate-responsive BIPV research facility in Bangalore

This paper describes the design and erection of a climate-responsive Building Integrated Photovoltaic (BIPV) structure in Bangalore, (12.58 N, 77.38 E) in the state of Karnataka, India. Building Integrated Photovoltaics integrate solar panels as part of a building structure (roofs and walls) with an aim to achieve self-sufficiency in the operation and occupant-comfort energy requirements. A joint collaboration between the Centre for Sustainable Technologies, Indian Institute of Science (IISc) and Bharat Heavy Electricals Limited (BHEL) is setting up a 70,000 US$ facility for research in BIPV structures. The structure utilizes low energy building materials like Stabilized Mud Blocks (SMB) integrated with a PV roof. Numerous challenges were overcome in the design of the BIPV roof including mechanisms for natural thermal comfort in response to Bangalore's climatic conditions. The paper presents the challenges overcome in the design and construction of a low energy, climate-responsive BIPV structure