Cyclic strain promotes shuttling of PYK2/Hic-5 complex from focal contacts in osteoblast-like cells.

International audienceWe showed that cyclic strain (CS) of osteoblastic cells induced tyrosine phosphorylation of two homologous tyrosine kinases FAK and PYK2, and of two homologous adaptor proteins paxillin and Hic5, with similar kinetics. Immunostaining showed that all four proteins were localized to focal contacts in controls. In contrast, the dynamics of their subcellular localization observed after CS differed. While FAK and paxillin remained at the focal contact, Hic-5 and PYK2 translocated outside ventral focal contacts as early as 30 min after CS and were sequestered by the cytoskeleton. Co-immunoprecipitation showed that the association of PYK2/Hic-5 and PYK2/FAK increased with time after strain while that of paxillin and Hic-5 decreased. Altogether these results suggested that CS regulates focal contact activity in osteoblasts by modulating PYK2-containing complexes in particular by shuttling out of the focal contact the adaptor Hic-5 and favoring the anchorage of FAK within contacts

Adhesion of Living Osteoblasts on Apatite Substrate Investigated by Atomic Force Microscopy

International audienc

Effect of silicon content on the sintering and biological behaviour of Ca10(PO4)(6-x)(SiO4)x(OH)(2-x) ceramics.

International audienceSilicated hydroxyapatite powders (Ca10(PO4)(6-x)(SiO4)x(OH)(2-x); Si(x)HA) were synthesized using a wet precipitation method. The sintering of Si(x)HA ceramics with 0 < or = x < or = 1 was investigated. For 0 < or = x < or = 0.5, the sintering rate and grain growth decreased slightly with the amount of silicate. For larger amounts, the sintering behaviour differed with the formation of secondary phases before total densification. Sintering parameters (temperature and time) were adjusted to each composition to produce dense materials having similar microstructure without formation of these secondary phases. Dense ceramics made of pure hydroxyapatite and Si(x)HA containing various amounts of silicate (up to x = 0.6) were biologically tested in vitro with human osteoblast-like cells. The proliferation of cells on the surface of the ceramics increased up to 5 days of culture, indicating that the materials were biocompatible. However, the silicon content did not influence the cell proliferation

The effect of dual frequency cyclic compression on matrix deposition by osteoblast-like cells grown in 3D scaffolds and on modulation of VEGF variant expression.

International audienceAs a strategy to optimise osteointegration of biomaterials by inducing proper extracellular matrix synthesis, and specifically angiogenic growth factor production and storage, we tested the effects of cyclic mechanical compression on 3D cultures of human osteoblast-like cells. MG-63 cells were seeded into 3D porous hydroxyapatite ceramics under vacuum to enable a homogenous cellular distribution. A four-day culture period allowed cell proliferation throughout the scaffolds. Low amplitude cyclic compressions were then applied to the scaffolds for 15 min with different regimens generated by the ZetOS system. A 3 Hz sinusoidal (sine) signal increased slightly collagen and fibronectin expression. When 50 Hz or 100 Hz vibrations were superimposed to the 3 Hz signal, matrix protein expression was down-regulated. In contrast, adding a 25 Hz vibration up-regulated significantly collagen and fibronectin. Moreover, expression of a matrix-bound variant of vascular endothelial growth factor-A (VEGF-A) was specifically stimulated compared to control or 3 Hz sine, and non-soluble VEGF protein was increased. Our study enabled us to identify low-amplitude, high-frequency strain regimen able to increase major matrix proteins of bone tissue and to regulate the expression of VEGF variants, showing that an appropriate combined loading has the potential to functionalise cellularized bone-like constructs

Multiscale grooved titanium processed with femtosecond laser influences mesenchymal stem cell morphology, adhesion, and matrix organization.

International audienceThe femtosecond laser processing enabled the structuring of six types of surfaces on titanium-6aluminium-4vanadium (Ti-6Al-4V) plates. The obtained hierarchical features consisted of a combination of microgrooves and oriented nanostructures. By adjusting beam properties such as laser polarization, the width of the microgrooves (20 or 60 μm) and the orientation of the nanostructures (parallel or perpendicular to the microgrooves) can be precisely controlled. Mesenchymal stem cells (MSCs) grown on these structured surfaces produced cytoplasmic extensions with focal contacts, while on the smooth titanium, the cells were found to be well spread and without any focal contact 12 h postseeding. The 600-nm wide nanostructures on their own were sufficient to orient the MSCs. For the multiscale structured areas, when the orientation of the nanostructures was orthogonal in relation to the microgrooves, there was an important decrease in or even a loss of cell alignment signifying that cells were sensitive to the directional nanostructures in the microgrooves. At 7 days, cell proliferation was not affected but the direction of nanostructures controlled the matrix organization. The ultrafast laser, as a new method for producing micro-nanohybrid surfaces, is a promising approach to promote desired tissue organization for tissue engineering

Ex Vivo bone formation in bovine trabecular bone cultured in a dynamic 3D bioreactor is enhanced by compressive mechanical strain.

Our aim was to test cell and trabecular responses to mechanical loading in vitro in a tissue bone explant culture model. We used a new three-dimensional culture model, the ZetOS system, which provides the ability to exert cyclic compression on cancellous bone cylinders (bovine sternum) cultured in forced flow circumfusion chambers, and allows to assess mechanical parameters of the cultivated samples. We evaluated bone cellular parameters through osteocyte viability test, gene and protein expression, and histomorphometric bone formation rate, in nonloaded versus loaded samples. The microarchitecture of bone cores was appraised by in vivo micro-CT imaging. After 3 weeks, the samples receiving daily cyclic compression exhibited increased osteoblast differentiation and activity associated with thicker, more plate-like-shaped trabeculae and higher Young's modulus and ultimate force as compared to unloaded samples. Osteoclast activity was not affected by mechanical strain, although it was responsive to drug treatments (retinoic acid and bisphosphonate) during the first 2 weeks of culture. Thus, in the ZetOS apparatus, we reproduce in vitro the osteogenic effects of mechanical strain known in vivo, making this system a unique and an essential laboratory aid for ex vivo testing of lamellar bone remodeling