30 research outputs found
ALBA HIGH VOLTAGE SPLITTER -POWER DISTRIBUTION TO ION PUMPS
Abstract High Voltage Splitter (HVS) is an equipment designed in Alba that allows a high voltage (HV) distribution (up to +7kV) from one ion pump controller up to eight ion pumps. Using it, the total number of high voltage power supplies needed in Alba's vacuum installation has decreased significantly. The current drawn by each splitter channel is measured independently inside a range from 10nA up to 10mA with 5% accuracy, those measurements are a base for vacuum pressure calculations. A relation, current-pressure depends mostly on the ion pump type, so different tools providing the full calibration flexibility have been implemented. Splitter settings, status and recorded data are accessible over a 10/100 Base-T Ethernet network, none the less a local (manual) control was implemented mostly for service purposes. The device supports also additional functions as a HV cable interlock, pressure interlock output cooperating with the facility's Equipment Protection System (EPS, ref: [1]), programmable pressure warnings/alarms and automatic calibration process based on an external current source. This paper describes the project, functionality, implementation, installation and operation as a part of the vacuum system at Alba
The vacuum system of MAX IV storage rings : Installation and conditioning
The installation of the vacuum system of the 3 GeV storage ring was started in November 2014 and finished in May 2015. In August 2015 the commissioning of the storage ring started, the first stored beam has been achieved on the 15th of September 2015. The installation of the vacuum system of the 1.5 GeV storage ring was done from September 2015 and the main part finished in December 2015, the connection to the Linac with the transfer line has been done in August 2016. In September 2016 the commissioning of the 1.5 GeV storage ring started with the first stored beam achieved on the 30th of September 2016. The vacuum system conditioning for the two rings was successful; the average dynamic pressure reduction and the increase in the lifetime with the accumulated beam dose is a demonstration of the good performance of the vacuum system. The installation procedure and the results of the conditioning together with the latest developments are introduced here
SESAME, A 3[sup rd] Generation Synchrotron Light Source for the Middle East
Developed under the auspices of UNESCO, SESAME is being established as an autonomous international research centre in the Middle East/Mediterranean region. It will have as its centrepiece a 2.5 GeV third Generation synchrotron light source with 13 straight sections for insertion devices and an emittance of 26.6 nm-rad. It will provide intense radiation from the IR to hard X-rays to a community that is expected to exceed 1000 users a few years after the start of operation in 2008
Recommended from our members
Commissioning of the MAX IV light source
The first of the so-called diffraction-limited storage rings (DLSRs), MAX I V, has now gone into operation. For this ring, a multibend achromat (MBA) lattice is employed in order to achieve a small electron beam emittance. Several non-conventional technical system solutions have been introduced in order to reduce size, cost, assembly time, installation effort and to increase the ring robustness. Examples of this are solid magnet blocks housing several magnet items, a fully NEG-coated vacuum system and a low frequency RF system. The commissioning started in late August 2015. Several base-line parameters have now been reached like a sufficiently high stored circulating current, beam lifetime and beam quality for beamline commissioning. The MBA concept and the operation of the non-conventional solutions technical systems are verified. This article describes some of the technical solutions chosen and the early commissioning results
Development and production of Non Evaporable Getter coatings for the vacuum chambers of the 3 GeV storage ring of MAX IV
MAX IV is presently under construction at Lund, Sweden, and the first beam for the production of synchrotron radiation is expected to circulate in 2016. The whole set of 3 GeV ring beam pipes is coated with Ti-Zr-V Non Evaporable Getter (NEG) thin film in order to fulfil the average pressure requirement of 1×10-9 mbar, despite the compact magnet layout and the large aspect ratio of the vacuum chambers. In this work, we present the optimizations of the coating process performed at CERN to coat different geometries and mechanical assembling used for the MAX IV vacuum chambers; the morphology of the thin films is analysed by Scanning Electron Microscopy; the composition and thickness is measured by Energy Dispersive X-ray analysis; the activation of the NEG thin film is monitored by X-ray Photoemission Spectroscopy; the vacuum performance of the coated beam pipes is evaluated by the measurement of hydrogen sticking coefficient. The results of the coating production characterization for the 84 units coated at CERN are presented